Can't build with CONFIG_NETFILTER=y/m on IA64, there's a missing
#include in net/ipv6/netfilter.c

net/ipv6/netfilter.c: In function `nf_ip6_checksum':
net/ipv6/netfilter.c:92: warning: implicit declaration of function
`csum_ipv6_magic'
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Noticed this use, fixed it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename policer specific _generic_ methods to be specific to
_act_police_
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.

IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config.  cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.

David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.

TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Besides removing lots of duplicate code, all converted users benefit
from improved HW checksum error handling. Tested with and without HW
checksums in almost all combinations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add checksum operation which takes care of verifying the checksum and
dealing with HW checksum errors and avoids multiple checksum
operations by setting ip_summed to CHECKSUM_UNNECESSARY after
successful verification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the queue rerouter intrastructure to a generic usable
infrastructure for address family specific operations as a base for
some cleanups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NAT is built as a module, ip_conntrack_netlink can not be linked
statically.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

default_rrq_ttl is used when no TTL is included in the RRQ.
Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move prototypes of NAT callbacks to ip_conntrack_h323.h. Because the
use of typedefs as arguments, some header files need to be moved as
well.
Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix section mismatch warnings caused by netfilter's init_or_cleanup
functions used in many places by splitting the init from the cleanup
parts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up hook registration by makeing use of the new mass registration and
unregistration helpers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].

The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch integrates the smcinit code into the smsc-ircc driver.
Some laptops have their smsc-ircc chip not properly configured by the
BIOS and needs some preconfiguration. Currently, this can be done from
userspace with smcinit, a utility that comes with the irda-utils
package. It messes with ioports and PCI settings, from userspace.  Now
with this patch, if we happen to be on one of the known to be faulty
laptops, we preconfigure the chip from the driver.

Patch from Linus Walleij <triad@df.lth.se>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes GRE and SIT to generate port unreachable instead of
protocol unreachable errors when we can't find a matching tunnel for a
packet.

This removes the ambiguity as to whether the error is caused by no
tunnel being found or by the lack of support for the given tunnel
type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

this fixes coverity bug id #1068.
hci_send_sco() frees skb if (skb->len > hdev->sco_mtu).
Since it returns a negative error value only in this case, we
can directly return here.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an off-by-21-or-49 error ;-) spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set .name in netconsole's struct console to identify the
struct's owner.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the sending of ICMP messages when there are no IPv4/IPv6
tunnels present to tunnel4/tunnel6 respectively.  Please note that for now
if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be
sent.  This is similar to how we handle AH/ESP/IPCOMP.

This move fixes the bug where we always send an ICMP message when there is
no ip6_tunnel device present for a given packet even if it is later handled
by IPsec.  It also causes ICMP messages to be sent when no IPIP tunnel is
present.

I've decided to use the "port unreachable" ICMP message over the current
value of "address unreachable" (and "protocol unreachable" by GRE) because
it is not ambiguous unlike the other ones which can be triggered by other
conditions.  There seems to be no standard specifying what value must be
used so this change should be OK.  In fact we should change GRE to use
this value as well.

Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel
where we don't check whether the embedded IPv6 header is present before
dereferencing it for the inside source address.

This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The conntrack code doesn't do re-fragmentation of defragmented packets
anymore but relies on fragmentation in the IP layer. Purely bridged
packets don't pass through the IP layer, so the bridge netfilter code
needs to take care of fragmentation itself.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seems like leaf (end-nodes) has been freed by __tnode_free_rcu and not
by __leaf_free_rcu. This fixes the problem. Only tnode_free is now
used which checks for appropriate node type. free_leaf can be removed.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to dereference x->encap before dereferencing it for encap_type.
If it's absent then the encap_type is zero.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

    security/selinux/xfrm.c: In function 'selinux_socket_getpeer_dgram':
    security/selinux/xfrm.c:284: error: 'struct sec_path' has no member named 'x'
    security/selinux/xfrm.c: In function 'selinux_xfrm_sock_rcv_skb':
    security/selinux/xfrm.c:317: error: 'struct sec_path' has no member named 'x'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This effectively undoes the PCI resource allocation changes done in
commit b408cbc7, but leaves the cleanups
of that commit in place.

We're going back to marking the resources reported by e820 busy _before_
doing PCI probing, so that any PCI resource that clashes with the BIOS-
reported memory map will be reloacted to a non-clashing area.

The reason? Larry Finger reports that his laptop has the cardbus
controller set up by the BIOS so that it conflicts with the e820 memory
map, and needs to be relocated. See

   http://bugzilla.kernel.org/show_bug.cgi?id=6337

for more details.

We'll have to work out how to handle the fbcon problem that caused that
commit in the first place in some other way.

Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: <bjk@luxsci.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Or rather compute it based on the table length automatically.

This also has the intended side effect of not warning for new system calls
anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix CONFIG_REORDER.

The value of cflags-y was assined to CFLAGS before cflags-y was assigned
the value used for CONFIG_REORDER.

Use cflags-y for all CFLAGS options in the Makefile to avoid this
happening again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:

   - the current/calling task has NOT set its own gs base yet to a
     non-zero value,

   - some other task that ran on the same processor previously set their
     own gs base to a non-zero value.

In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.

However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.

    Change the arch_prctl() ARCH_GET_GS code to only read and return
    the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
    task is non-zero.

    Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
    a task can also setup a gs base value by using modify_ldt() and write
    an index value into 'gs' from user space, the patch below reads
    'gs' instead of using thread.gs, since in the modify_ldt() case,
    the thread.gs value will be 0, and incorrect value would be returned
    (the task->thread.gs value).

    When the user has not set its own gs base value and the 'gs'
    register is zero, then the MSR_KERNEL_GS_BASE register will not be
    read and a value of zero will be returned by reading and returning
    'task->thread.gs'.

    The first patch shown below is an attempt at implementing this
    approach.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Printk doesn't have any value
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).

If HZ changes, this drift can become even more pronounced.

HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.

Vojtech comments:

  "It's not entirely correct (it assumes the HPET ticks totally
   exactly), but it's significantly better than assuming the PIT error
   there."
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Mostly to get better handling when a extended config space
access has to fallback to Type1.

Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Previously only the first bus would be checked against Type 1.

Why 16? Checking all would need too much memory and we
can assume that systems with more than 16 busses have better than
average quality BIOS.

This is an additional defense against bad MCFG tables.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fixup the read mostly section to start at internode cacheline boundary.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>