Skip to content

L
linux-davinci
Switch branch/tag
  1. 26 Oct, 2008 6 commits
    • Alistair John Strachan's avatar
      hwmon: (abituguru3) Cosmetic whitespace fixes · 4777e4e6
      Alistair John Strachan authored 
      As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.

Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.

Doesn't alter any kernel text, just data.
Signed-off-by: default avatarAlistair John Strachan <alistair@devzero.co.uk>
Reported-by: default avatarJustin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
      4777e4e6
    • Jean Delvare's avatar
      hwmon: (adt7473) Fix voltage conversion routines · be821b78
      Jean Delvare authored 
      Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.

According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
      be821b78
    • Jean Delvare's avatar
      hwmon: (lm90) Add support for the LM99 16 degree offset · 97ae60bb
      Jean Delvare authored 
      The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
      97ae60bb
    • Jean Delvare's avatar
      hwmon: (lm90) Fix handling of hysteresis value · ec38fa2b
      Jean Delvare authored 
      There are several problems in the way the hysteresis value is handled
by the lm90 driver:

* In show_temphyst(), specific handling of the MAX6646 is missing, so
  the hysteresis is reported incorrectly if the critical temperature
  is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
  the chip but data->temp_hyst isn't updated accordingly, so there is
  a short period of time (up to 2 seconds) where the old hystereris
  value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
  to compute the value of the hysteresis register lacks
  device-specific handling. As a result, the value of the hysteresis
  register might be incorrect for the ADT7461 and MAX6646 chips.

Fix these 3 bugs.
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
      ec38fa2b
    • Jean Delvare's avatar
      hwmon-vid: Add support for AMD family 10h CPUs · 1b871826
      Jean Delvare authored 
      The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
      1b871826
    • Geert Uytterhoeven's avatar
      hwmon: (w83781d) Fix linking when built-in · dd56b638
      Geert Uytterhoeven authored 
      When w83781d is built-in, the final links fails with the following vague error
message:

`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o

w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: default avatarGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
      dd56b638
  3. 24 Oct, 2008 5 commits
  5. 23 Oct, 2008 29 commits