This patch fixes two bugs in the dm9000 network driver:

- Don't read one byte too much in 8bit mode.
- release correct resource
Signed-off-by: Jochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

Patch indents dmfe.txt to look like other docs.  It adds a tip about CNET
cards using Davicom chipsets.  Also it removes parts where it refers to how
to build driver out-of-kernel which seems to be cruft from times where the
driver was out of the kernel.
Signed-off-by: Ismail Donmez <ismail@kde.org.tr>
Signed-off-by: Domen Puncer <domen@coderock.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

Signed-off-by: Andrew Morton <akpm@osdl.org>

Fix int vs. pm_message_t confusion in airo. Should change no code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t.  Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.

The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type

This is basically a guess:

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.

Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Use msleep_interruptible() instead of schedule_timeout() to guarantee
the task delays as expected.

This patch removes some obviously dead code found by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>

This patch fixes the LITTLE_ENDIAN #define and a function prototype.
Signed-off-by: Adrian Bunk <bunk@stusta.de>

This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings
Signed-off-by: Adrian Bunk <bunk@stusta.de>

During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).

Improvement:
instead of *always* calculating
lea    0x2c0(%edx),%ebx
and then additionally doing the
mov    %edx,0xc0(%ebx)
addition *if we need it*,

we now do the *whole* calculation of
mov    %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.

Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.

Thank you for your support,

Andreas Mohr

old asm result (using gcc 3.3.5):

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       8d 9a c0 02 00 00       lea    0x2c0(%edx),%ebx
    15aa:       e8 fc ff ff ff          call   15ab <ei_irq_wrapper+0xb>
    15af:       83 f8 01                cmp    $0x1,%eax
    15b2:       74 03                   je     15b7 <ei_irq_wrapper+0x17>
    15b4:       5b                      pop    %ebx
    15b5:       5d                      pop    %ebp
    15b6:       c3                      ret
    15b7:       31 d2                   xor    %edx,%edx
    15b9:       89 93 c0 00 00 00       mov    %edx,0xc0(%ebx)
    15bf:       eb f3                   jmp    15b4 <ei_irq_wrapper+0x14>
    15c1:       eb 0d                   jmp    15d0 <ei_watchdog>
    15c3:       90                      nop
    15c4:       90                      nop
    15c5:       90                      nop
    15c6:       90                      nop
    15c7:       90                      nop
    15c8:       90                      nop
    15c9:       90                      nop
    15ca:       90                      nop
    15cb:       90                      nop
    15cc:       90                      nop
    15cd:       90                      nop
    15ce:       90                      nop
    15cf:       90                      nop

000015d0 <ei_watchdog>:

new asm result:

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       89 d3                   mov    %edx,%ebx
    15a6:       e8 fc ff ff ff          call   15a7 <ei_irq_wrapper+0x7>
    15ab:       83 f8 01                cmp    $0x1,%eax
    15ae:       74 03                   je     15b3 <ei_irq_wrapper+0x13>
    15b0:       5b                      pop    %ebx
    15b1:       5d                      pop    %ebp
    15b2:       c3                      ret
    15b3:       31 d2                   xor    %edx,%edx
    15b5:       89 93 80 03 00 00       mov    %edx,0x380(%ebx)
    15bb:       eb f3                   jmp    15b0 <ei_irq_wrapper+0x10>
    15bd:       8d 76 00                lea    0x0(%esi),%esi

000015c0 <ei_watchdog>:
Signed-off-by: Andrew Morton <akpm@osdl.org>

Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()

This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.

See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>

Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:

arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug
Signed-off-by: Magnus Damm <damm@opensource.se>

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>

The spin loop in 8139cp is limited to 100 iterations when pulling hardware
stats. There is no allowance for processor speed so on a fast machine, the
stats may not be available that fast. Also, if the board doesn't return
soon enough make sure turn the address back off to prevent later updates
when memory has gone away.

This patch updates the name identifier to list both of the Marvell PHYs
that are supported.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>

Add support for alternate slave selection algorithms to bonding
balance-xor and 802.3ad modes.  Default mode (what we have now: xor of
MAC addresses) is "layer2", new choice is "layer3+4", using IP and port
information for hashing to select peer.

Originally submitted by Jason Gabler for balance-xor mode;
modified by Jay Vosburgh to additionally support 802.3ad mode.  Jason's
original comment is as follows:

The attached patch to the Linux Etherchannel Bonding driver modifies the
driver's "balance-xor" mode as follows:

      - alternate hashing policy support for mode 2
        * Added kernel parameter "xmit_policy" to allow the specification
          of different hashing policies for mode 2.  The original mode 2
          policy is the default, now found in xmit_hash_policy_layer2().
        * Added xmit_hash_policy_layer34()

This patch was inspired by hashing policies implemented by Cisco,
Foundry and IBM, which are explained in
Foundry documentation found at:
http://www.foundrynet.com/services/documentation/sribcg/Trunking.html#112750Signed-off-by: Jason Gabler <jygabler@lbl.gov>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>

Add support for generating gratuitous ARPs in bonding
active-backup mode when failovers occur.  Includes support for VLAN
tagging the ARPs as needed.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>

Patch from Lennert Buytenhek

Compiling one kernel that supports both ixdp2400 and ixdp2800 gives
an error, as a copy of the ixdp2400 irq init routing accidentally
ended up in ixdp2800.c somehow.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add a mapping for the ixp2400 and ixp2800 msf unit.  The msf is the
ixp2000's 'media and switch fabric' unit, which handles the networking
part of the chip.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add a comment to asm/arch-ixp2000/ixp2000-regs.h describing the
ixp2000 virtual memory map layout.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

As the ixdp cpld mappings now live at 0xfe000000, we can push
VMALLOC_END upwards to 0xfb000000, where the first iotable mapping
begins.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

All ixdp platforms currently have a cpld mapped in at 0xfafff000.
Since this address is not 1M-aligned, a regular page mapping will be
used instead of a section mapping, which opens up the possibility of
triggering ixp2400 erratum #66 as we only do the XCB=101 workaround
thing for section mappings.
There is still a lot of space higher up in the virtual memory map
for 1M mappings, so move the cpld mapping to 0xfe000000 and make it
1M big so that a section mapping will be used for it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

VST needs to know which timer handler is for the timer interrupt.
Mark all timer interrupts with the SA_TIMER flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The pending registers for IRQ1-IRQ7 were pointing to the interrupt pending
register instead of the external one.
Signed-off-by: Tony Li <Tony.Li@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Since the Trivial Patch Monkey is mentioned both in steps 4.  and 5., I
removed it from step4 (Select e-mail destination), since it should go under
'Select your CC list'.
Signed-off-by: Cosmin Nicolaescu <cos@camelot.homelinux.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Another swsusp fixup.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Missed conversion in the swsusp cleanup.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

After the previous fix in 2.6.12, this patch should properly fix the
radeon IRQ handling code.

From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>

The parentheses were missing. Noted by Pavel Machek.

1. Establish a simple API for process freezing defined in linux/include/sched.h:

   frozen(process)		Check for frozen process
   freezing(process)		Check if a process is being frozen
   freeze(process)		Tell a process to freeze (go to refrigerator)
   thaw_process(process)	Restart process
   frozen_process(process)	Process is frozen now

2. Remove all references to PF_FREEZE and PF_FROZEN from all
   kernel sources except sched.h

3. Fix numerous locations where try_to_freeze is manually done by a driver

4. Remove the argument that is no longer necessary from two function calls.

5. Some whitespace cleanup

6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
   cleared before setting PF_FROZEN, recalc_sigpending does not check
   PF_FROZEN).

This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>