Finish decoupling the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.

Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.

Eventually all boards should just associate a regulator with
each MMC controller they use.  In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control.  As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.

These calls are intended to be used by MMC host adapters
using at least one regulator per host.  Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Minor cleanups to the twl403 regulator driver, mostly enabled
by other recent changes:  comments, shrink memory usage, add
definition for one bit.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update previously-posted twl4030 regulator driver to export
supported voltages to upper layers using a new mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add a basic mechanism for regulators to report the discrete
voltages they support:  list_voltage() enumerates them using
selectors numbered from 0 to an upper bound.

Use those methods to force machine-level constraints into bounds.
(Example:  regulator supports 1.8V, 2.4V, 2.6V, 3.3V, and board
constraints for that rail are 2.0V to 3.6V ... so the range of
voltages is then 2.4V to 3.3V on this board.)

Export those voltages to the regulator consumer interface, so for
example regulator hooked up to an MMC/SD/SDIO slot can report the
actual voltage options available to cards connected there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Tony Lindgren <tony@atomide.com>

The associated registers need to be defined too.
Signed-off-by: Tony Lindgren <tony@atomide.com>

The reboot mode can be communicated to a bootloader (or the
kernel itself) with a scratchpad register. This functionality
is especially useful, if userspace is allowed to change
the reboot mode.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add 1 to buffer length for null terminator.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

It seems the regulator framework is going to require boards
to explicitly configure voltage ranges, instead of letting
them just pick up the entire available range.  So this patch
updates OMAP3 board handling for VMMC1, VMMC2, and VSIM.

Also, change the label for the MMC1 DAT4..DAT7 supply to
"vmmc_aux", so the label isn't specific to MMC1.  Things
like SDIO and eMMC chips may also need a second voltage,
though in that case it's usually 1.8V for chip interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Sort 34xx GPIO pins, add few more pins
Signed-off-by: Tony Lindgren <tony@atomide.com>

This replaces earlier patch from Sergio Aguirre titled "[REVIEW PATCH 03/14]
OMAP34XX: CAM: Resources fixes".
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update OMAP3 EVM board support to support the MMC/SD switches,
when used with the twl4030 based power card.

Also, less usefully, LEDB as a GPIO LED ... it's on the underside
of the board, so it's probably not very useful to most folk.  The
LCD backlight is controlled by LEDA though; more useful, though
its PWM mode might not be practical on this board (I don't know
how that inductor will affect things).

This is done from schematics, so it needs testing (and maybe some
bugfixes) from folk with an EVM board.

- Dave
Signed-off-by: Tony Lindgren <tony@atomide.com>

sync up with the version going upstream.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove now obsolete TAG_USB and make omap_usb_init() available
for omap2 boards using it like H4 and Apollon.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branches 'master' and 'linus'

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ixp4xx - Fix qmgr_request_queue build failure
  crypto: api - Fix module load deadlock with fallback algorithms

There is another user of IXP4xx queue manager, fix it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: don't allow setuid to succeed if the user does not have rt bandwidth
  sched_rt: don't start timer when rt bandwidth disabled

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: oprofile: don't set counter width from cpuid on Core2
  x86: fix init_memory_mapping() to handle small ranges

* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86 mmiotrace: fix race with release_kmmio_fault_page()
  x86 mmiotrace: improve handling of secondary faults
  x86 mmiotrace: split set_page_presence()
  x86 mmiotrace: fix save/restore page table state
  x86 mmiotrace: WARN_ONCE if dis/arming a page fails
  x86: add far read test to testmmiotrace
  x86: count errors in testmmiotrace.ko

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: Teach RCU that idle task is not quiscent state at boot

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] fix lots of ARM __devexit sillyness
  [ARM] 5417/1: Set the correct cacheid for ARMv6 CPUs with ARMv7 style MMU
  [ARM] 5416/1: Use unused address in v6_early_abort
  [ARM] 5411/1: S3C64XX: Fix EINT unmask
  [ARM] at91: fix for Atmel AT91 powersaving
  [ARM] RiscPC: Fix etherh oops

`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack.  If the store succeeeds this
corrupts r0 in pt_regs.  Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Impact: fix stuck NMIs and non-working oprofile on certain CPUs

Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.

This should fix bug #12395:

  http://bugzilla.kernel.org/show_bug.cgi?id=12395Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix failed EFI bootup in certain circumstances

Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.

It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit 155b25bc, which was
totally wrong - the "embedded" options still exists (very much so) even
on non-embedded platforms.

It's just that we don't bother with actually asking about them when
we're not embedded, we just take their default values (which is usually
'y' - the options add features that may not be worth it in a constrained
environment).
Noticed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Fix use-before-null-check in i915_irq_emit().
  drm: Avoid client deadlocks when the master disappears.
  drm: Wake up all lock waiters when the master disappears.
  drm: Don't return ERESTARTSYS to user-space.

This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

This is done by
1) Wake up lock waiters when we close the master file descriptor.
   Not when the master structure is removed, since the latter
   requires the waiters themselves to release the refcount on the
   master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
   Normally these clients will get a SIGPIPE when the X server dies,
   but clients may also spin trying to grab the DRM lock, without
   getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED
menu.  Fix by moving it to just after all of the EMBEDDED menu symbols.

Also, surround all of the EMBEDDED symbols with "if EMBEDDED"/"endif" so
that this EMBEDDED block is clearer.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
  sdhci: Add quirk for controllers with no end-of-busy IRQ