Signed-off-by: Kevin Hilman <khilman@mvista.com>

Now that the EVM can treat its GPIO expanders as banks of normal
GPIOs (albeit ones that require sleeping accessors), remove the old
LED code in favor of the more generic support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Declare two of the three I2C GPIO expanders to the EVM board init logic, and
use them.  One hooks up to the LEDs using the leds-gpio driver; the other
exposes a switch to sysfs, and initializes the audio clocks.

The third expander is currently handled by gpio_expander_davinci.c (which
has not yet gone upstream, and probably can't), so a patch to handle that
expander should remove that file and its users.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Switch DaVinci over to using the new GPIO library, so it can access
GPIO expanders and other non-SOC GPIOs using the same calls.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

UART_DAVINCI_PWREMU is a 2-byte register, but davinci_serial_outp only
writes a single byte.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This reverts part of commit 8b232558.
If a signal terminates a write transfer the bus would lock up and
the next read or write would give "timeout waiting for bus ready."
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

mainline won't accept a non-zero default delay.
If a platform needs this, it must override the platform
data. My device doesn't need this. I don't know
if the dvevm does or not.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Cleanup spacing and spelling mistakes.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

The I2C EMAC code for reading the MAC address from EEPROM uses
deadbeEf in one place and deadbeAf in others as a magic string. As a
result, all DVEVMs actually get the same default MAC address. Here,
we correct them to the British English spelling of beef to fix the
issue and avoid further confusion (hopefully).
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This fixes compilation after 2.6.25-rc8 merge, but needs a real
implementation.
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This fixes Oops at kernel startup while "scanning" for TLV320AIC23IDx
addresses.
Signed-off-by: Alexander Vasiliev <alexvasiljev@gmail.com>
Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This reverts commit a8e67c9d.

Current driver does not work on EVM because we need to enable ATA
pins via the GPIO expander. This is not the best way to do it, but I
don't have a better one yet.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

GPIO expander failure case did not unlock a mutex (e.g. when the I2C
bus could not be found). Fix that.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

dev->id for the i2c platform device is now 1, instead of 0.
Update the GPIO expander to realise that.
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This reverts commit 5d641071.

- Get i2c adapter with address 1 not 0 in davinci_i2c_expander_read
- Unlock mutex on error exit path in davinci_i2c_expander_op
Signed-off-by: Yusuf Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

[Sorry, the previous patch was a copy/paste mistake, this one should be
better]

I have no access to the docs for this chip but I'm pretty sure the current
address of the two DIDR1 registers is wrong because it's outside the
TUSB-specific register space.  The modified address in turn has a good
chance to be correct.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixed output from checkpatch.pl and got rid of double spaces.
Signed-off-by: Tony Lindgren <tony@atomide.com>

While getting trying to get the keyboard driver to accept my
keyboard layout I found and fixed a few bugs.

- Fixed the driver to respect the matrix size and .rep
  fields from "struct omap_kp_platform_data"

- Fixed misc. configuration problems.

- Fixed some problems with the interrupt/polling code by
  implementing 100% event driven scan handling (there
  was a race between the timer and interrupt initiated
  calls to twl_4030_kp_scan()).

- Too many interrupts was delivered -> enable "PENDING_DISABLE".

- The controller would hang with keys stuck on -> program
  KEYP_TIMEOUT so sensible timeout.

Other enhancements:

- Simple ghost key suppression.
- Support for non-matrix switches. That is switches connected
  between GND and a row.

To configure the driver for the non-matrix switches you add the
key as you normally would, but the col-index will have to be the
same value as the col-size.

For example with .cols = 2 and you will use the value "2" for
COL for the two non-matrix switches:

static int rocket_control_keymap[] = {
	/* COL ROW */
	KEY(0,  0, KEY_3),
	KEY(0,  1, KEY_2),
	KEY(1,  0, KEY_1),
	KEY(1,  1, KEY_LAUNCH),
	KEY(2,  0, KEY_ABORT),
	KEY(2,  1, KEY_SD),
	0
}

Cleanup:

I might have gone too far when fixing the twl4030-keypad.h file,
but I was loosing breath and attention spelling my way through
these 32+ letter identifiers with names like:

    BIT_KEYP_CTRL_REG_TOLE_EN_MASK

which is a bit in the register:

   REG_KEYP_CTRL_REG

leading to statements like:

   twl4030_kpwrite_u8(TWL4030_MODULE_KEYPAD,
           BIT_KEYP_CTRL_REG_TOLE_EN_MASK, REG_KEYP_CTRL_REG);

What I did was to take out all the redundant stuff like BIT, REG
and MASK, making reading a little easier:

   twl4030_kpwrite_u8(TWL4030_MODULE_KEYPAD,
                      KEYP_CTRL_TOLE_EN, KEYP_CTRL);

There was a lot of configuration stuff in header file that wasn't
really needed. I think I even found a joke:

.h had this line:
   #define BIT_PTV_REG_PTV4                       (0x4)

.c had this:
       /* Set Pre Scalar Field PTV to 4 */
       reg = BIT_LK_PTV_REG_PTV_MASK & (BIT_PTV_REG_PTV4 << BIT_LK_PTV_REG_PTV);
Signed-off-by: Klaus Pedersen <klaus.k.pedersen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP2430/3430 contain an 1.8V-only MMC2 host that is not properly
supported by the current driver.  This patch contains changes to
correctly set up this host.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Acked-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds device configuration to provide second HSMMC slot support
on OMAP 2430 and 3430 boards.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>

Change CONFIG_ARCH_OMAP24XX by CONFIG_ARCH_OMAP243X macro when this config
is needed only for 2430 boards.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Acked-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branches 'master' and 'linus'

Refresh palmz71_defconfig
Signed-off-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change error to warning for twl4030 clock init
Signed-off-by: Tony Lindgren <tony@atomide.com>

davinci_request_dma() was using -1 as an array index for dmaqnum[].
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Troy found that mmc_davinci_start_command was previously enabling
interrupts too early. This was allowing a TX interrupt to be handled
while the FIFO was being stuffed, resulting in an overstuffed fifo.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Make sure FIFO does not need to be serviced before handling other
interrupt sources.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Use rw_threshold where appropriate instead of assuming it is 32.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

This patch improves performance for filling the FIFO by rewriting in
assembly, and as a side-effect fixes odd-byte transfers.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bernard Blackham <bernard@largestprime.net>
Signed-off-by: Kevin Hilman <khilman@mvista.com>

Small typo in the patch recently merged to avoid the unused symbol
message for count_partial(). Discussion thread with confirmation of fix at
http://marc.info/?t=120696854400001&r=1&w=2

Typo in the check if we need the count_partial function that was
introduced by 53625b42Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-ohci: plug dma memory leak in AR handler

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
  sh: Fix up uImage compression type
  remove include/asm-sh/floppy.h
  sh: Fix TIF_USEDFPU clearing under FPU emulation.
  sh: Fix occasional FPU register corruption under preempt.

* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/ralf/upstream-linus:
  [MIPS] XSS1500: Fix compilation
  [MIPS] Bigsur: make defconfig more useful.
  [MIPS] Alchemy: work around clock misdetection on early Au1000
  [MIPS] Add missing 4KEC TLB refill handler
  [MIPS] BCM1480: Fix PCI/HT IO access
  [MIPS] Fix the installation condition of MIPS clocksource
  [MIPS] Check for GCC r10k-cache-barrier support
  [MIPS] I8253: Export i2853_lock to modules.
  [MIPS] VPE loader: Check result of memory allocation.

This patch corrects an error in the driver it8712f_wdt.  You cannot set
the 16-bit WDT_TIMEOUT access as a 16-bit outw, because the byte
ordering will be wrong.  So just do the high 8 bits as a separate
access.
Signed-off-by: Oliver Schuster <olivers137@aol.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4875/1: Add MODULE_ALIAS to ixp4xx-beeper module
  [ARM] 4873/1: Fix ITE 8152 interrupt demux
  [ARM] 4878/1: Add oabi shim for fstatat64