Some new models need to disable wireless hotplug.
For the moment, we don't know excactly what models need that,
except 1005HA.
Users will be able to use that param as a workaround.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>

This is a short term workaround for Eeepc 1005HA.

refs: <http://bugzilla.kernel.org/show_bug.cgi?id=14570>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>

The EeePC 4G ("701") implements CFVS, but it is not supported by the
pre-installed OS, and the original option to change it in the BIOS
setup screen was removed in later versions.  Judging by the lack of
"Super Hybrid Engine" on Asus product pages, this applies to all "701"
models (4G/4G Surf/2G Surf).

So Asus made a deliberate decision not to support it on this model.
We have several reports that using it can cause the system to hang [1].
That said, it does not happen all the time.  Some users do not
experience it at all (and apparently wish to continue "right-clocking").

Check for the EeePC 701 using DMI.  If met, then disable writes to the
"cpufv" sysfs attribute and log an explanatory message.

Add a "cpufv_disabled" attribute which allow users to override this
policy.  Writing to this attribute will log a second message.

The sysfs attribute is more useful than a module option, because it
makes it easier for userspace scripts to provide consistent behaviour
(according to user configuration), regardless of whether the kernel
includes this change.

[1] <http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=559578>
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] tape_char: add missing compat_ptr conversion
  [S390] zcrypt: add sanity check before copy_from_user()
  [S390] unwire sys_recvmmsg again
  [S390] con3215: remove empty ioctl function
  [S390] dasd: add proper compat pointer conversion for symmetrix ioctl
  [S390] mmap: add missing compat_ptr conversion to both mmap compat syscalls
  [S390] bug: implement arch specific __WARN macro
  [S390] Move __cpu_logical_map to smp.c
  [S390] tape_block: remove ioctl function
  [S390] smp: remove volatile type quilifier from __cpu_logical_map
  [S390] smp: setup smp_processor_id early
  [S390] use helpers for rlimits
  [S390] fs3270: add missing compat ptr conversion
  [S390] vmcp: add missing compat ptr conversion
  [S390] cio: add missing compat ptr conversion
  [S390] dasd: add missing compat ptr conversion
  [S390] remove superfluous TIF_USEDFPU bit
  [S390] duplicate SIGTRAP on signal delivery.
  [S390] clear TIF_SINGLE_STEP for new process.
  [S390] fix loading of PER control registers for utrace.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
  net: fix build erros with CONFIG_BUG=n, CONFIG_GENERIC_BUG=n
  ipv6: skb_dst() can be NULL in ipv6_hop_jumbo().
  tg3: Update copyright and driver version
  tg3: Disable 5717 serdes and B0 support
  tg3: Add reliable serdes detection for 5717 A0
  tg3: Fix std rx prod ring handling
  tg3: Fix std prod ring nicaddr for 5787 and 57765
  sfc: Fix conditions for MDIO self-test
  sfc: Fix polling for slow MCDI operations
  e1000e: workaround link issues on busy hub in half duplex on 82577/82578
  e1000e: MDIO slow mode should always be done for 82577
  ixgbe: update copyright dates
  ixgbe: Do not attempt to perform interrupts in netpoll when down
  cfg80211: fix refcount imbalance when wext is disabled
  mac80211: fix queue selection for data frames on monitor interfaces
  iwlwifi: silence buffer overflow warning
  iwlwifi: disable tx on beacon update notification
  iwlwifi: fix iwl_queue_used bug when read_ptr == write_ptr
  mac80211: fix endian error
  mac80211: add missing sanity checks for action frames
  ...

Fixed build errors introduced by commit 7ad6848c (ip: fix mc_loop
checks for tunnels with multicast outer addresses)
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes CERT-FI FICORA #341748

Discovered by Olli Jarva and Tuomo Untinen from the CROSS
project at Codenomicon Ltd.

Just like in CVE-2007-4567, we can't rely upon skb_dst() being
non-NULL at this point.  We fixed that in commit
e76b2b25 ("[IPV6]: Do no rely on
skb->dst before it is assigned.")

However commit 483a47d2 ("ipv6: added
net argument to IP6_INC_STATS_BH") put a new version of the same bug
into this function.

Complicating analysis further, this bug can only trigger when network
namespaces are enabled in the build.  When namespaces are turned off,
the dev_net() does not evaluate it's argument, so the dereference
would not occur.

So, for a long time, namespaces couldn't be turned on unless SYSFS was
disabled.  Therefore, this code has largely been disabled except by
people turning it on explicitly for namespace development.

With help from Eugene Teo <eugene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the copyright notice for 2010 and updates the version
number to 3.106.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The B0 revision of the 5717 will not get enough testing by the time
2.6.33 ships.  Since the kernel is already at RC3, serdes support
will require too many patches to fix.  For these reasons, this patch
disables 5717 serdes support and will refuse to attach to all 5717
devices that are later than an A0 revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The serdes status bit does not work as intended for the 5717 A0.
This patch implements an alternative detection scheme that will only be
valid for A0 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some tg3 devices that require the driver to post new rx
buffers in smaller increments.  Commit
4361935a, "tg3: Consider
rx_std_prod_idx a hw mailbox" changed how the driver tracks the rx
producer ring updates, but it does not make any special considerations
for the above-mentioned devices.  For those devices, it is possible for
the driver to hit the special case path, which updates the hardware
mailbox register but skips updating the shadow software mailbox member.
If the special case path represents the final mailbox update for this
ISR iteration, the hardware and software mailbox values will be out of
sync.  Ultimately, this will cause the driver to use a stale mailbox
value on the next iteration, which will appear to the hardware as a
large rx buffer update.  Bad things ensue.

The fix is to update the software shadow mailbox member when the special
case path is taken.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 87668d35, titled "tg3: Don't
touch RCB nic addresses", tried to avoid assigning the nic address of
the standard producer ring.  Unfortunately, the default nic address is
not correct for the 5787, the 5755M, or the 57765.  This patch
reenables the old behavior and opts out of the assignment only
for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Tested-by: Chow Loong Jin <hyperair@ubuntu.com>
Tested-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO self-test should not be run on boards without an MDIO PHY,
such as SFN5122F-R3 and later revisions.  It should also not try to
address a specific MMD in an MDIO clause 22 PHY.  Check the
mode_support field to decide which mode to use, if any.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is down and we are using polled mode for MCDI
operations, we busy-wait for completion for approximately 1 jiffy
using udelay() and then back off to schedule().  But the completion
will not wake the task, since we are using polled mode!  We must use
schedule_timeout_uninterruptible() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes a delay in hardware after every received packet allowing
more time for transmitted packets to go out in between received packets in
half duplex.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A previous 82577 workaround that set the MDIO access speed to slow mode for
every PHY register read/write when the cable is unplugged should instead
set the access mode to always be slow before any PHY register access.
Since the mode bit gets cleared when the PHY is reset, set the mode after
every PHY reset.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves issues seen when running netconsole and rebooting via
reboot -f.  The issue was due to the fact that we were attempting to
perform interrupt actions when the q_vectors and rings had already been
freed via the ixgbe_shutdown routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
  xen: fix hang on suspend.

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: change drm set mode messages as DRM_DEBUG
  drm: fix crtc no modes printf + typo
  drm/radeon/kms: only evict to GTT if CP is ready
  drm/radeon/kms: Fix crash getting TV info with no BIOS.
  drm/radeon/kms/rv100: reject modes > 135 Mhz on DVI (v2)
  drm/radeon/kms/r6xx+: make irq handler less verbose
  drm/radeon/kms: fix up LVDS handling on macs (v2)

Commit ac4c2a3b broke the build
of all powerpc boot wrappers.

It attempts to add an include of autoconf.h but used the wrong
path for it. It also adds -D__KERNEL__ to our boot wrapper, both
things that we pretty much didn't do on purpose so far.

We want our boot wrapper to remain independent enough of the kernel
for various reasons, one of them being that you can "wrap" an existing
kernel at distro install time which allows to ship one kernel image
and a set of boot wrappers for different platforms, the wrappers
don't have to be built out of the same kernel build tree.

It's also incorrect to do what the patch does in our boot environment
since we may not have a proper alignment exception handler which means
we may not be able to fixup the few cases where an unaligned access will
need SW emulation (depends on the core variant, could be when crossing
page or segment boundaries for example).

This patch fixes it by putting the old code back in and using the
new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
is set, which happens not to be set on powerpc since we don't include
autoconf.h. It also reverts the changes to our boot wrapper Makefile.

This means that x86 should, afaik, keep the optimisations since its
boot wrapper does include autoconf.h and define __KERNEL__ (though I
doubt they make that much different outside of slow embedded processors).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: wacom: Add BTN_TOOL_FINGER for pad button reporting
  HID: add device IDs for new model of Apple Wireless Keyboard
  HID: fix pad button definition in hid-wacom
  HID: Support 171 byte variant of Samsung USB IR receiver
  HID: blacklist ET&T TC5UH touchscreen controller

* 'for-33' of git://repo.or.cz/linux-kbuild:
  Makefile: do not override LC_CTYPE
  kbuild: really fix bzImage build with non-bash sh

If __block_prepare_write() was failed in block_write_begin(), the
allocated blocks can be outside of ->i_size.

But new truncate_pagecache() in vmtuncate() does nothing if new < old.
It means the above usage is not working anymore.

So, this patch fixes it by removing "new < old" check. It would need
more cleanup/change. But, now -rc and truncate working is in progress,
so, this tried to fix it minimum change.
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* fasync-helper:
  fasync: split 'fasync_helper()' into separate add/remove functions

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

It's not obvious that copy_from_user() is called with a sane length
parameter here. Even though it currently seems to be correct better
add a check to prevent stack corruption / exploits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

sys_recvmmsg is reachable via sys_socketcall. So unwire it again since
there is no point in having two entry points for it.
Also put it to the ignore list so we don't get reminded anymore in order
to wire it up.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

...instead of adding a compat ioctl function which would do nothing
as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

This one will trap, generates shorter code and emits better debug data
than the generic version.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

This is just a complicated construct which always returns -EINVAL.
Just remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove pointless qualifier.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

smp_processor_id() is supposed to work before setup_arch() gets called.
Before that smp_processor_id() may return just an arbitrary value that
is contained in the uninitialized boot lowcore.
So provide the arch function which will override the weak function in
init/main.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.

I.e. either use rlimit helpers added in
3e10e716
or ACCESS_ONCE if not applicable.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add missing compat ptr conversion including two additional
whitespace changes that aren't worth a separate patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>