- 10 Apr, 2006 27 commits
-
-
Paolo 'Blaisorblade' Giarrusso authored
Noticed this use, fixed it. Signed-off-by:
Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jamal Hadi Salim authored
Rename policer specific _generic_ methods to be specific to _act_police_ Signed-off-by:
Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by:
-
Michael Chan authored
Speed up SRAM read and write functions if possible by using MMIO instead of config. cycles. With this change, the post reset signature done at the end of D3 power change must now be moved before the D3 power change. IBM reported a problem on powerpc blades during ethtool self test that was caused by the memory test taking excessively long. Config. cycles are very slow on powerpc and the memory test can take more than 10 seconds to complete using config. cycles. David Miller informed me that an earlier version of the patch caused problems on sparc64 systems with built-in tg3 chips. This version fixes the problem by excluding all SUN built-in tg3 chips from doing MMIO SRAM access. TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are built-in and do not require Vaux switching. Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not very useful. This will free up some bits for new flags. Signed-off-by: -
Patrick McHardy authored
Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Patrick McHardy authored
Besides removing lots of duplicate code, all converted users benefit from improved HW checksum error handling. Tested with and without HW checksums in almost all combinations. Signed-off-by:
-
Patrick McHardy authored
Add checksum operation which takes care of verifying the checksum and dealing with HW checksum errors and avoids multiple checksum operations by setting ip_summed to CHECKSUM_UNNECESSARY after successful verification. Signed-off-by:
-
Patrick McHardy authored
Change the queue rerouter intrastructure to a generic usable infrastructure for address family specific operations as a base for some cleanups. Signed-off-by:
-
Patrick McHardy authored
When NAT is built as a module, ip_conntrack_netlink can not be linked statically. Signed-off-by:
-
Jing Min Zhao authored
default_rrq_ttl is used when no TTL is included in the RRQ. Signed-off-by:
Jing Min Zhao <zhaojingmin@users.sourceforge.net> Signed-off-by:
-
Jing Min Zhao authored
Signed-off-by:
-
Jing Min Zhao authored
Signed-off-by:
-
Jing Min Zhao authored
Move prototypes of NAT callbacks to ip_conntrack_h323.h. Because the use of typedefs as arguments, some header files need to be moved as well. Signed-off-by:
-
Patrick McHardy authored
Fix section mismatch warnings caused by netfilter's init_or_cleanup functions used in many places by splitting the init from the cleanup parts. Signed-off-by:
-
Patrick McHardy authored
Clean up hook registration by makeing use of the new mass registration and unregistration helpers. Signed-off-by:
-
Patrick McHardy authored
Signed-off-by:
-
Samuel Ortiz authored
This patch enables support for the Sigmatel's STIR421x IrDA chip. Once patched with Sigmatel's firmware, this chip "almost" follows the USB-IrDA spec. Thus this patch is against irda-usb.[ch]. The code has been tested by Nick Fedchik on an STIR4210 chipset based dongle. Signed-off-by:
Samuel Ortiz <samuel.ortiz@nokia.com> Signed-off-by:
-
Linus Walleij authored
This patch integrates the smcinit code into the smsc-ircc driver. Some laptops have their smsc-ircc chip not properly configured by the BIOS and needs some preconfiguration. Currently, this can be done from userspace with smcinit, a utility that comes with the irda-utils package. It messes with ioports and PCI settings, from userspace. Now with this patch, if we happen to be on one of the known to be faulty laptops, we preconfigure the chip from the driver. Patch from Linus Walleij <triad@df.lth.se> Signed-off-by:
-
Herbert Xu authored
This patch changes GRE and SIT to generate port unreachable instead of protocol unreachable errors when we can't find a matching tunnel for a packet. This removes the ambiguity as to whether the error is caused by no tunnel being found or by the lack of support for the given tunnel type. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Eric Sesterhenn authored
this fixes coverity bug id #1068. hci_send_sco() frees skb if (skb->len > hdev->sco_mtu). Since it returns a negative error value only in this case, we can directly return here. Signed-off-by:
Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by:
-
Adrian Bunk authored
This patch fixes a memory leak (buf wasn't freed) spotted by the Coverity checker. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Adrian Bunk authored
This patch fixes an off-by-21-or-49 error ;-) spotted by the Coverity checker. Signed-off-by:
-
Randy Dunlap authored
Set .name in netconsole's struct console to identify the struct's owner. Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Acked-by:
Matt Mackall <mpm@selenic.com> Signed-off-by:
-
Herbert Xu authored
This patch moves the sending of ICMP messages when there are no IPv4/IPv6 tunnels present to tunnel4/tunnel6 respectively. Please note that for now if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be sent. This is similar to how we handle AH/ESP/IPCOMP. This move fixes the bug where we always send an ICMP message when there is no ip6_tunnel device present for a given packet even if it is later handled by IPsec. It also causes ICMP messages to be sent when no IPIP tunnel is present. I've decided to use the "port unreachable" ICMP message over the current value of "address unreachable" (and "protocol unreachable" by GRE) because it is not ambiguous unlike the other ones which can be triggered by other conditions. There seems to be no standard specifying what value must be used so this change should be OK. In fact we should change GRE to use this value as well. Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel where we don't check whether the embedded IPv6 header is present before dereferencing it for the inside source address. This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>. Signed-off-by:
-
Patrick McHardy authored
The conntrack code doesn't do re-fragmentation of defragmented packets anymore but relies on fragmentation in the IP layer. Purely bridged packets don't pass through the IP layer, so the bridge netfilter code needs to take care of fragmentation itself. Signed-off-by:
-
Robert Olsson authored
Seems like leaf (end-nodes) has been freed by __tnode_free_rcu and not by __leaf_free_rcu. This fixes the problem. Only tnode_free is now used which checks for appropriate node type. free_leaf can be removed. Signed-off-by:
Robert Olsson <robert.olsson@its.uu.se> Signed-off-by:
-
Herbert Xu authored
We need to dereference x->encap before dereferencing it for encap_type. If it's absent then the encap_type is zero. Signed-off-by:
-
- 09 Apr, 2006 13 commits
-
-
Dave Jones authored
security/selinux/xfrm.c: In function 'selinux_socket_getpeer_dgram': security/selinux/xfrm.c:284: error: 'struct sec_path' has no member named 'x' security/selinux/xfrm.c: In function 'selinux_xfrm_sock_rcv_skb': security/selinux/xfrm.c:317: error: 'struct sec_path' has no member named 'x' Signed-off-by:Dave Jones <davej@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
This effectively undoes the PCI resource allocation changes done in commit b408cbc7, but leaves the cleanups of that commit in place. We're going back to marking the resources reported by e820 busy _before_ doing PCI probing, so that any PCI resource that clashes with the BIOS- reported memory map will be reloacted to a non-clashing area. The reason? Larry Finger reports that his laptop has the cardbus controller set up by the BIOS so that it conflicts with the e820 memory map, and needs to be relocated. See http://bugzilla.kernel.org/show_bug.cgi?id=6337 for more details. We'll have to work out how to handle the fbcon problem that caused that commit in the first place in some other way. Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Antonino A. Daplas <adaplas@pol.net> Cc: <bjk@luxsci.net> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Andi Kleen authored
Signed-off-by:
Andi Kleen <ak@suse.de> Signed-off-by:
-
Andi Kleen authored
Or rather compute it based on the table length automatically. This also has the intended side effect of not warning for new system calls anymore. Signed-off-by:
-
Sam Ravnborg authored
Fix CONFIG_REORDER. The value of cflags-y was assined to CFLAGS before cflags-y was assigned the value used for CONFIG_REORDER. Use cflags-y for all CFLAGS options in the Makefile to avoid this happening again. Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
John Blackwood authored
In linux-2.6.16, we have noticed a problem where the gs base value returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if: - the current/calling task has NOT set its own gs base yet to a non-zero value, - some other task that ran on the same processor previously set their own gs base to a non-zero value. In this situation, the ARCH_GET_GS code will read and return the MSR_KERNEL_GS_BASE msr register. However, since the __switch_to() code does NOT load/zero the MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back the value of some previous tasks's gs base value instead of 0. Change the arch_prctl() ARCH_GET_GS code to only read and return the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling task is non-zero. Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...), a task can also setup a gs base value by using modify_ldt() and write an index value into 'gs' from user space, the patch below reads 'gs' instead of using thread.gs, since in the modify_ldt() case, the thread.gs value will be 0, and incorrect value would be returned (the task->thread.gs value). When the user has not set its own gs base value and the 'gs' register is zero, then the MSR_KERNEL_GS_BASE register will not be read and a value of zero will be returned by reading and returning 'task->thread.gs'. The first patch shown below is an attempt at implementing this approach. Signed-off-by: -
Andi Kleen authored
Printk doesn't have any value Signed-off-by:
-
Jordan Hargrave authored
If the HPET timer is enabled, the clock can drift by ~3 seconds a day. This is due to the HPET timer not being initialized with the correct setting (still using PIT count). If HZ changes, this drift can become even more pronounced. HPET patch initializes tick_nsec with correct tick_nsec settings for HPET timer. Vojtech comments: "It's not entirely correct (it assumes the HPET ticks totally exactly), but it's significantly better than assuming the PIT error there." Signed-off-by:
-
Andi Kleen authored
Mostly to get better handling when a extended config space access has to fallback to Type1. Cc: gregkh@suse.de Signed-off-by:
-
Andi Kleen authored
Previously only the first bus would be checked against Type 1. Why 16? Checking all would need too much memory and we can assume that systems with more than 16 busses have better than average quality BIOS. This is an additional defense against bad MCFG tables. Signed-off-by:
-
Ravikiran G Thirumalai authored
Fixup the read mostly section to start at internode cacheline boundary. Signed-off-by:
Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by:
Shai Fultheim <shai@scalex86.org> Signed-off-by:
-
Andi Kleen authored
Signed-off-by:
-
Andi Kleen authored
Fix WARNING: vmlinux: 'strlen' exported twice. Previous export was in vmlinux Reported by Mats Johannesson Signed-off-by:
-
