- 20 Apr, 2009 3 commits
-
-
Divy Le Ray authored
Release vectors when a MSI-X allocation fails. Signed-off-by:
Divy Le Ray <divy@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Divy Le Ray authored
The fatal error task can be scheduled while processing an offload packet in NAPI context when the connection handle is bogus. this can race with the ports being brought down and the cxgb3 workqueue being flushed. Stop napi processing before flushing the work queue. The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()). The driver however does not flush any work on keventd_wq while being unloaded. This patch also fixes this. Also call cancel_delayed_work_sync in place of the the deprecated cancel_rearming_delayed_workqueue. Signed-off-by:
-
Divy Le Ray authored
Use the existing periodic task to handle link faults. The link fault interrupt handler is also called in work queue context, which is wrong and might cause potential deadlocks. Signed-off-by:
-
- 17 Apr, 2009 21 commits
-
-
Patrick McHardy authored
Check whether the underlying device provides a set of ethtool ops before checking for individual handlers to avoid NULL pointer dereferences. Reported-by:
Art van Breemen <ard@telegraafnet.nl> Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
-
-
Christian Lamparter authored
Signed-off-by:
Christian Lamparter <chunkeey@web.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The TIM IE must not be shorter than 4 bytes, so verify that when parsing it. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Johannes Berg authored
Instead, allocate extra IE memory if necessary. Normally, this isn't even necessary since there's enough space. This is a better way of correcting the "held BSS can disappear" issue, but also a lot more code. It is also necessary for proper auth/assoc BSS handling in the future. Signed-off-by:
-
Johannes Berg authored
When we receive a probe response frame we can replace the BSS struct in our list -- but if that struct is held then we need to hold the new one as well. We really should fix this completely and not replace the struct, but this is a bandaid for now. Signed-off-by:
-
Johannes Berg authored
Using the scan_sdata variable here is terribly wrong, if there has never been a scan then we fail. However, we need a bandaid... Signed-off-by:
-
Pablo Neira Ayuso authored
With this patch, nfnetlink returns -ENOMEM instead of -EPERM if we fail to create the nfnetlink netlink socket during the module loading. This is exactly what rtnetlink does in this case. Ideally, it would be better if we propagate the error that has happened in netlink_kernel_create(), however, this function still does not implement this yet. Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
This patch fixes an inconsistency that results in no error reports to user-space listeners if we fail to allocate the event message. Signed-off-by:
-
Herbert Xu authored
After calling skb_gro_receive skb->len can no longer be relied on since if the skb was merged using frags, then its pages will have been removed and the length reduced. This caused tcp_gro_receive to prematurely end merging which resulted in suboptimal performance with ixgbe. The fix is to store skb->len on the stack. Reported-by:
Mark Wagner <mwagner@redhat.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Oliver Neukum authored
EPERM means that disconnect() is runnung. It should be treated like ENODEV Signed-off-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Oliver Hartkopp authored
Since commit ead2ceb0 ("Network Drop Monitor: Adding kfree_skb_clean for non-drops and modifying end-of-line points for skbs") so called end-of-line points for skb's should use consume_skb() to free the socket buffer. In opposite to consume_skb() the function kfree_skb() is intended to be used for unexpected skb drops e.g. in error conditions that now can trigger the network drop monitor if enabled. This patch moves the skb end-of-line point in af_can.c to use consume_skb(). Signed-off-by:
Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by:
-
Erik Waling authored
Suppose that we receive lots of frames, start processing them, but exhaust our budget so that we return before we had a chance to look at all of them. Then, when the network layer calls us again, we will only continue processing the buffers if the REC bit was set in the mean time, which it might not be if there was a brief pause in the flow of packets. If this happens, we'll simply display a warning and call netif_rx_complete() with potentially lots of unprocessed packets in the RX ring... Fix this by scanning the ring no matter what flags are set in the interrupt status register. Signed-off-by:
Erik Waling <erik.waling@konftel.com> Signed-off-by:
Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by:
-
Erik Waling authored
When transfering large amounts of data we sometimes experienced that the Retry Limit Exceeded (RLE) bit got set in TSR during transmission attempts. When this happened the driver would stall in a state that prevented any more data from being sent. Signed-off-by:
-
PJ Waskiewicz authored
The thresholds for the DCB priority flow control are incorrect for 82599. This fixes the thresholds to be correct. Signed-off-by:
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
PJ Waskiewicz authored
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when running with 8 traffic classes, and runs 64-32-16 when running with 4 traffic classes. This patch fixes the mapping. Signed-off-by:
-
Jesse Brandeburg authored
If the e1000 transmit cleanup inner loop exited early, then cleaned might not be true. This could cause tx hangs or other badness. Use count to track the total number of descriptors cleaned instead of basing a tx queue restart off of a temporary working state variable. This code now makes the flow the same for e1000/e1000e/igb/ixgbe Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
If the e1000e transmit cleanup inner loop exited early, then cleaned might not be true. This could cause tx hangs or other badness. Use count to track the total number of descriptors cleaned instead of basing a tx queue restart off of a temporary working state variable. This code now makes the flow the same for e1000/e1000e/igb/ixgbe Signed-off-by:
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
Signed-off-by:
-
- 16 Apr, 2009 16 commits
-
-
-
Tony Breeds authored
GCC warns: drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task': drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around operand of '!' or change '&' to '&&' or '!' to '~' Which I think is right. Bracket to remove ambiguity. Signed-off-by:
Tony Breeds <tony@bakeyournoodle.com> Signed-off-by:
-
Patrick McHardy authored
The removal of the SAME target accidentally removed one feature that is not available from the normal NAT targets so far, having multi-range mappings that use the same mapping for each connection from a single client. The current behaviour is to choose the address from the range based on source and destination IP, which breaks when communicating with sites having multiple addresses that require all connections to originate from the same IP address. Introduce a IP_NAT_RANGE_PERSISTENT option that controls whether the destination address is taken into account for selecting addresses. http://bugzilla.kernel.org/show_bug.cgi?id=12954Signed-off-by:
-
Johannes Berg authored
arm will pad even between u8's, so mark the structs/unions packed. Fixes a build bug on arm due to BUILD_BUG_ON tests in the code. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Pavel Roskin authored
If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly 100 readings, we wrongly consider it a timeout. Rewrite the clever while loop as a for loop that does the right thing and looks simpler. Reported by Juha Leppanen <juha_motorsportcom@luukku.com> Signed-off-by:
Pavel Roskin <proski@gnu.org> Signed-off-by:
-
Gerrit Renker authored
mac80211: Fragmentation threshold (typo) ieee80211_ioctl_siwfrag() sets the fragmentation_threshold to 2352 when frame fragmentation is to be disabled, yet the corresponding 'get' function tests for 2353 bytes instead. This causes user-space tools to display a fragmentation threshold of 2352 bytes even if fragmentation has been disabled. Signed-off-by:
Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by:
-
Herton Ronaldo Krzesinski authored
In a scenario where there isn't any firmware available, we will have a double kfree of rt2x00dev->spec.channels_info when ieee80211_register_hw returns an error status inside rt2x00lib_probe_hw. The problem is that if ieee80211_register_hw fails, we call rt2x00lib_remove_hw twice: * first inside rt2x00lib_probe_hw upon failure of ieee80211_register_hw * error status is returned to rt2x00lib_probe_dev, which then sees it and calls in this case rt2x00lib_remove_dev that will again run rt2x00lib_remove_hw Prevent this avoiding calling rt2x00lib_remove_hw inside rt2x00lib_probe_hw Problem was detected with CONFIG_DEBUG_PAGEALLOC=y, CONFIG_SLUB_DEBUG=y, CONFIG_SLUB_DEBUG_ON=y, that dumps this with no firmware available: rt61pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 wmaster0 (rt61pci): not using net_device_ops yet phy0: Selected rate control algorithm 'pid' phy0: Failed to initialize wep: -2 phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw. ============================================================================= BUG kmalloc-128: Object already free ----------------------------------------------------------------------------- INFO: Allocated in rt61pci_probe_hw+0x3e5/0x6e0 [rt61pci] age=340 cpu=0 pid=21 INFO: Freed in rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] age=0 cpu=0 pid=21 INFO: Slab 0xc13ac3e0 objects=23 used=10 fp=0xdd59f6e0 flags=0x400000c3 INFO: Object 0xdd59f6e0 @offset=1760 fp=0xdd59f790 Bytes b4 0xdd59f6d0: 15 00 00 00 b2 8a fb ff 5a 5a 5a 5a 5a 5a 5a 5a ....².ûÿZZZZZZZZ Object 0xdd59f6e0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f6f0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f700: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f710: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f720: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f730: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f740: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object 0xdd59f750: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk¥ Redzone 0xdd59f760: bb bb bb bb »»»» Padding 0xdd59f788: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ Pid: 21, comm: stage1 Not tainted 2.6.29.1-desktop-1.1mnb #1 Call Trace: [<c01abbb3>] print_trailer+0xd3/0x120 [<c01abd37>] object_err+0x37/0x50 [<c01acf57>] __slab_free+0xe7/0x2f0 [<c01ad1de>] kfree+0x7e/0xd0 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] [<e0e4a239>] rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] [<e0e4acc7>] rt2x00lib_remove_dev+0x37/0x50 [rt2x00lib] [<e0e4b087>] rt2x00lib_probe_dev+0x1a7/0x3b0 [rt2x00lib] [<e0eb288f>] rt2x00pci_probe+0xdf/0x1ee [rt2x00pci] [<c026b9ee>] local_pci_probe+0xe/0x10 [<c026c750>] pci_device_probe+0x60/0x80 [<c02d5c2a>] driver_probe_device+0x9a/0x2e0 [<c02d5ef9>] __driver_attach+0x89/0x90 [<c02d541b>] bus_for_each_dev+0x4b/0x70 [<c026c690>] ? pci_device_remove+0x0/0x40 [<c02d59d9>] driver_attach+0x19/0x20 [<c02d5e70>] ? __driver_attach+0x0/0x90 [<c02d4cef>] bus_add_driver+0x1cf/0x2a0 [<c026c690>] ? pci_device_remove+0x0/0x40 [<c02d60c9>] driver_register+0x69/0x140 [<c026c9b0>] __pci_register_driver+0x40/0x80 [<e0ecc000>] ? rt61pci_init+0x0/0x19 [rt61pci] [<e0ecc017>] rt61pci_init+0x17/0x19 [rt61pci] [<c0101116>] do_one_initcall+0x26/0x1c0 [<c01ab90c>] ? slab_pad_check+0x3c/0x120 [<c01ab90c>] ? slab_pad_check+0x3c/0x120 [<c01ac8da>] ? check_object+0xda/0x210 [<c01b0026>] ? percpu_free+0x46/0x50 [<c01ad09e>] ? __slab_free+0x22e/0x2f0 [<c01b0026>] ? percpu_free+0x46/0x50 [<c01b0026>] ? percpu_free+0x46/0x50 [<c01b0026>] ? percpu_free+0x46/0x50 [<c01687ec>] ? stop_machine_destroy+0x3c/0x40 [<c015e515>] ? load_module+0xa5/0x1c50 [<e0ec5000>] ? rt61pci_eepromregister_read+0x0/0x40 [rt61pci] [<e0eb2000>] ? rt2x00pci_write_tx_data+0x0/0x90 [rt2x00pci] [<c03ac2fb>] ? mutex_lock+0xb/0x20 [<c03ac2fb>] ? mutex_lock+0xb/0x20 [<c017ad16>] ? tracepoint_update_probe_range+0x76/0xa0 [<c017ad6f>] ? tracepoint_module_notify+0x2f/0x40 [<c03b02ed>] ? notifier_call_chain+0x2d/0x70 [<c014f0ed>] ? __blocking_notifier_call_chain+0x4d/0x60 [<c014f11a>] ? blocking_notifier_call_chain+0x1a/0x20 [<c0160156>] sys_init_module+0x96/0x1d0 [<c019dad6>] ? sys_munmap+0x46/0x60 [<c0105546>] syscall_call+0x7/0xb FIX kmalloc-128: Object at 0xdd59f6e0 not freed rt61pci 0000:00:07.0: PCI INT A disabled rt61pci: probe of 0000:00:07.0 failed with error -2 Signed-off-by:
Herton Ronaldo Krzesinski <herton@mandriva.com.br> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Johannes Berg authored
I forgot that iwl3945 registration is separate from iwlagn. Signed-off-by:
-
Michael Buesch authored
On Sunday 05 April 2009 11:29:38 Michael Buesch wrote: > On Sunday 05 April 2009 11:23:59 Jaswinder Singh Rajput wrote: > > With latest linus tree I am getting, .config file attached: > > > > [ 22.895051] r8169: eth0: link down > > [ 22.897564] ADDRCONF(NETDEV_UP): eth0: link is not ready > > [ 22.928047] ADDRCONF(NETDEV_UP): wlan0: link is not ready > > [ 22.982292] libvirtd used greatest stack depth: 4200 bytes left > > [ 63.709879] wlan0: authenticate with AP 00:11:95:9e:df:f6 > > [ 63.712096] wlan0: authenticated > > [ 63.712127] wlan0: associate with AP 00:11:95:9e:df:f6 > > [ 63.726831] wlan0: RX AssocResp from 00:11:95:9e:df:f6 (capab=0x471 status=0 aid=1) > > [ 63.726855] wlan0: associated > > [ 63.730093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > > [ 74.296087] wlan0: no IPv6 routers present > > [ 79.349044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 119.358200] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 179.354292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 259.366044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 359.348292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 361.953459] packagekitd used greatest stack depth: 4160 bytes left > > [ 478.824258] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 598.813343] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 718.817292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 838.824567] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 958.815402] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1078.848434] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1198.822913] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1318.824931] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1438.814157] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1558.827336] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1678.823011] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1798.830589] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 1918.828044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 2038.827224] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 2116.517152] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 2158.840243] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > [ 2278.827427] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request > > > I think this message should only show if CONFIG_MAC80211_VERBOSE_DEBUG is set. > It's kind of expected that we lose a beacon once in a while, so we shouldn't print > verbose messages to the kernel log (even if they are KERN_DEBUG). > > And besides that, I think one can easily remotely trigger this message and flood the logs. > So it should probably _also_ be ratelimited. Something like this: Signed-off-by:Michael Buesch <mb@bu3sch.de>
-
Michael Buesch authored
The assertion of the lock-bit in the hardware register is unreliable, because there are devices with quirks that will randomly set the bit. Do the assertion in software, only. Signed-off-by:
-
Ivo van Doorn authored
Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
Christian Lamparter authored
This patch adds a new device to ar9170usb. Reported-by:
Mike Kershaw/Dragorn <dragorn@kismetwireless.net> Signed-off-by:
-
Dan Williams authored
Code was clearly wrong, plus callers expect the mode change to happen as soon as possible, not dropped on the floor until the next time some other config value changes and a commit happens. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Jamie Lentin authored
Add USB device ID for OQO 01+'s internal wireless LAN An OQO employee mentions the chip's true identity here:- ftp://ftp.oqo.com/unsupported/linux/OQOLinux.htmlSigned-off-by:Jamie Lentin <jm@lentin.co.uk> Acked-by:
Kalle Valo <kalle.valo@iki.fi> Signed-off-by:
-
Philip Rakity authored
Don't lead memory when receive errors Signed-off-by:
Philip Rakity <prakity@yahoo.com> Acked-by:
-
