Signed-off-by: Nicolas Pitre <nico@marvell.com>

Signed-off-by: Nicolas Pitre <nico@marvell.com>

Signed-off-by: Nicolas Pitre <nico@marvell.com>

ts78xx add NAND support via plat_nand
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>

amend RTC registering to not depend on ifdef's
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>

Added checks to the platform_device_(register|add) calls so that if
a device failed to load it would then not later be unloaded; also
added the hooks so that it would not try to unload when the RTC
driver support is compiled out.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>

The A0 revision of the mv78xx0 development board has four ethernet
ports, with PHY IDs 8-11, whereas the Z0 version has two, with PHY
addresses 8-9.  This patch configures the third and fourth ethernet
port to use the PHY addresses on the A0 board to enable use of those
ports -- if we are running on a Z0 board, the ge10/11 setup code in
common.c will force these back to PHYless mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

On pre-A0 revisions of the mv78xx0 SoC, the third and fourth
ethernet interface are not brought out to pins, but are internally
cross-connected, so if we run on pre-A0 silicon, we'll force eth2
and eth3 to PHYless mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

During boot, identify which chip stepping we're running on (determined
by looking at the first PCIe unit's device ID and revision registers),
and print a message with the details about what we found.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This allows for board support code to set up their MPP config if the
bootloader didn't do it all or did it wrong.  This also allows to
register usable GPIOs.
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Especially on Kirkwood, a couple GPIOs are actually only output capable.
Let's separate the ability to configure a GPIO as input or output to
accommodate this restriction.
Signed-off-by: Nicolas Pitre <nico@marvell.com>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5405/1: ep93xx: remove unused gesbc9312.h header
  [ARM] 5404/1: Fix condition in arm_elf_read_implies_exec() to set READ_IMPLIES_EXEC
  [ARM] omap: fix clock reparenting in omap2_clk_set_parent()
  [ARM] 5403/1: pxa25x_ep_fifo_flush() *ep->reg_udccs always set to 0
  [ARM] 5402/1: fix a case of wrap-around in sanity_check_meminfo()
  [ARM] 5401/1: Orion: fix edge triggered GPIO interrupt support
  [ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
  [ARM] 5391/1: AT91: Enable GPIO clocks earlier
  [ARM] 5390/1: AT91: Watchdog fixes
  [ARM] 5398/1: Add Wan ZongShun to MAINTAINERS for W90P910
  [ARM] omap: fix _omap2_clksel_get_src_field()
  [ARM] omap: fix omap2_divisor_to_clksel() error return value

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, mce: fix ifdef for 64bit thermal apic vector clear on shutdown
  x86, mce: use force_sig_info to kill process in machine check
  x86, mce: reinitialize per cpu features on resume
  x86, rcu: fix strange load average and ksoftirqd behavior

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: limit the number of loops the ring buffer self test can make
  tracing: have function trace select kallsyms
  tracing: disable tracing while testing ring buffer
  tracing/function-graph-tracer: trace the idle tasks

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] fix "mem=" handling in case of standby memory
  [S390] Fix timeval regression on s390
  [S390] sclp: handle empty event buffers

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: virtuoso: revert "do not overwrite EEPROM on Xonar D2/D2X"
  ALSA: jack - Use card->shortname for input name
  ALSA: usb-audio - Workaround for misdetected sample rate with CM6207
  ALSA: usb-audio - Fix non-continuous rate detection
  sound: usb-audio: fix uninitialized variable with M-Audio MIDI interfaces
  Revert "Sound: hda - Restore PCI configuration space with interrupts off"

Remove the gesbc9312.h header since it is unused.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

READ_IMPLIES_EXEC must be set when:
o binary _is_ an executable stack (i.e. not EXSTACK_DISABLE_X)
o processor architecture is _under_ ARMv6 (XN bit is supported from ARMv6)
Signed-off-by: Makito SHIOKAWA <lkhmkt@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

commit aa5e97ce
[PATCH] improve precision of process accounting.

Introduced a timing regression:
-bash-3.2# time ls
real    0m0.006s
user    0m1.754s
sys     0m1.094s

The problem was introduced by an error in cputime_to_timeval.
Cputime is now 1/4096 microsecond, therefore, we have to divide
the remainder with 4096 to get the microseconds.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Handle a malformed hardware response which some versions of the
Support Element (SE) may present during SE restart and which otherwise
would result in an endless loop in function sclp_dispatch_evbufs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When changing the parent of a clock, it is necessary to keep the
clock use counts balanced otherwise things the parent state will
get corrupted.  Since we already disable and re-enable the clock,
we might as well use the recursive versions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

*ep->reg_udccs is always set to 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

In the non highmem case, if two memory banks of 1GB each are provided,
the second bank would evade suppression since its virtual base would
be 0.  Fix this by disallowing any memory bank which virtual base
address is found to be lower than PAGE_OFFSET.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'tip/tracing/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into tracing/urgent

This reverts commit 7e86c0e6 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.

More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect.  In other words, the presence of this
driver does not have any effect on the occurrence of the error.  (So
far, the available evidence seems to point to a BIOS bug.)

Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.

The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Impact: prevent deadlock if ring buffer gets corrupted

This patch adds a paranoid check to make sure the ring buffer consumer
does not go into an infinite loop. Since the ring buffer has been set
to read only, the consumer should not loop for more than the ring buffer
size. A check is added to make sure the consumer does not loop more than
the ring buffer size.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>

Impact: fix output of function tracer to be useful

The function tracer is pretty useless if KALLSYMS is not configured.
Unless you are good at reading hex values, the function tracer should
select the KALLSYMS configuration.

Also, the dynamic function tracer will fail its self test if KALLSYMS
is not selected.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>

Impact: fix to prevent hard lockup on self tests

If one of the tracers are broken and is constantly filling the ring
buffer while the test of the ring buffer is running, it will hang
the box. The reason is that the test is a consumer that will not
stop till the ring buffer is empty. But if the tracer is broken and
is constantly producing input to the buffer, this test will never
end. The result is a lockup of the box.

This happened when KALLSYMS was not defined and the dynamic ftrace
test constantly filled the ring buffer, because the filter failed
and all functions were being traced. Something was being called
that constantly filled the buffer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
  block: fix booting from partitioned md array
  block: revert part of 18ce3751
  cciss: PCI power management reset for kexec
  paride/pg.c: xs(): &&/|| confusion
  fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
  block: fix bad definition of BIO_RW_SYNC
  bsg: Fix sense buffer bug in SG_IO

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  omap_hsmmc: Change while(); loops with finite version
  omap_hsmmc: recover from transfer failures
  omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V
  omap_hsmmc: card detect irq bugfix
  sdhci: fix led naming
  mmc_test: fix basic read test
  s3cmci: Fix hangup in do_pio_write()
  Revert "sdhci: force high speed capability on some controllers"
  MMC: fix bug - SDHC card capacity not correct

Enhanced lockdep coverage of __GFP_NOFS turned up this new lockdep
assert:

[ 1093.677775]
[ 1093.677781] =================================
[ 1093.680031] [ INFO: inconsistent lock state ]
[ 1093.680031] 2.6.29-rc5-tip-01504-gb49eca1-dirty #1
[ 1093.680031] ---------------------------------
[ 1093.680031] inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
[ 1093.680031] kswapd0/308 [HC0[0]:SC0[0]:HE1:SE1] takes:
[ 1093.680031]  (&inode->inotify_mutex){+.+.?.}, at: [<c0205942>] inotify_inode_is_dead+0x20/0x80
[ 1093.680031] {RECLAIM_FS-ON-W} state was registered at:
[ 1093.680031]   [<c01696b9>] mark_held_locks+0x43/0x5b
[ 1093.680031]   [<c016baa4>] lockdep_trace_alloc+0x6c/0x6e
[ 1093.680031]   [<c01cf8b0>] kmem_cache_alloc+0x20/0x150
[ 1093.680031]   [<c040d0ec>] idr_pre_get+0x27/0x6c
[ 1093.680031]   [<c02056e3>] inotify_handle_get_wd+0x25/0xad
[ 1093.680031]   [<c0205f43>] inotify_add_watch+0x7a/0x129
[ 1093.680031]   [<c020679e>] sys_inotify_add_watch+0x20f/0x250
[ 1093.680031]   [<c010389e>] sysenter_do_call+0x12/0x35
[ 1093.680031]   [<ffffffff>] 0xffffffff
[ 1093.680031] irq event stamp: 60417
[ 1093.680031] hardirqs last  enabled at (60417): [<c018d5f5>] call_rcu+0x53/0x59
[ 1093.680031] hardirqs last disabled at (60416): [<c018d5b9>] call_rcu+0x17/0x59
[ 1093.680031] softirqs last  enabled at (59656): [<c0146229>] __do_softirq+0x157/0x16b
[ 1093.680031] softirqs last disabled at (59651): [<c0106293>] do_softirq+0x74/0x15d
[ 1093.680031]
[ 1093.680031] other info that might help us debug this:
[ 1093.680031] 2 locks held by kswapd0/308:
[ 1093.680031]  #0:  (shrinker_rwsem){++++..}, at: [<c01b0502>] shrink_slab+0x36/0x189
[ 1093.680031]  #1:  (&type->s_umount_key#4){+++++.}, at: [<c01e6d77>] shrink_dcache_memory+0x110/0x1fb
[ 1093.680031]
[ 1093.680031] stack backtrace:
[ 1093.680031] Pid: 308, comm: kswapd0 Not tainted 2.6.29-rc5-tip-01504-gb49eca1-dirty #1
[ 1093.680031] Call Trace:
[ 1093.680031]  [<c016947a>] valid_state+0x12a/0x13d
[ 1093.680031]  [<c016954e>] mark_lock+0xc1/0x1e9
[ 1093.680031]  [<c016a5b4>] ? check_usage_forwards+0x0/0x3f
[ 1093.680031]  [<c016ab74>] __lock_acquire+0x2c6/0xac8
[ 1093.680031]  [<c01688d9>] ? register_lock_class+0x17/0x228
[ 1093.680031]  [<c016b3d3>] lock_acquire+0x5d/0x7a
[ 1093.680031]  [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031]  [<c08824c4>] __mutex_lock_common+0x3a/0x4cb
[ 1093.680031]  [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031]  [<c08829ed>] mutex_lock_nested+0x2e/0x36
[ 1093.680031]  [<c0205942>] ? inotify_inode_is_dead+0x20/0x80
[ 1093.680031]  [<c0205942>] inotify_inode_is_dead+0x20/0x80
[ 1093.680031]  [<c01e6672>] dentry_iput+0x90/0xc2
[ 1093.680031]  [<c01e67a3>] d_kill+0x21/0x45
[ 1093.680031]  [<c01e6a46>] __shrink_dcache_sb+0x27f/0x355
[ 1093.680031]  [<c01e6dc5>] shrink_dcache_memory+0x15e/0x1fb
[ 1093.680031]  [<c01b05ed>] shrink_slab+0x121/0x189
[ 1093.680031]  [<c01b0d12>] kswapd+0x39f/0x561
[ 1093.680031]  [<c01ae499>] ? isolate_pages_global+0x0/0x233
[ 1093.680031]  [<c0157eae>] ? autoremove_wake_function+0x0/0x43
[ 1093.680031]  [<c01b0973>] ? kswapd+0x0/0x561
[ 1093.680031]  [<c0157daf>] kthread+0x41/0x82
[ 1093.680031]  [<c0157d6e>] ? kthread+0x0/0x82
[ 1093.680031]  [<c01043ab>] kernel_thread_helper+0x7/0x10

inotify_handle_get_wd() does idr_pre_get() which does a
kmem_cache_alloc() without __GFP_FS - and is hence deadlockable under
extreme MM pressure.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: MinChan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since I don't work for SUSE any more and the bwalle@suse.de address is
invalid, correct it in the copyright headers and documentation.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Build breaks when DELL_LAPTOP=y and POWER_SUPPLY=m.  DELL_LAPTOP needs to
depend on POWER_SUPPLY.

dell-laptop.c:(.text+0x1ef3c4): undefined reference to `power_supply_is_system_supplied'
dell-laptop.c:(.text+0x1ef45e): undefined reference to `power_supply_is_system_supplied'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>