This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Additional cleanup for debug boards on H2/P2/H3/H4:  move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices).  Make H4 use that.

This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.

It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.

In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO).  Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix typo in gpio
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is one extra brace in z71 board file, this patch fixes it.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Fri, Oct 27, 2006 at 05:16:59PM +0100, Jonathan McDowell wrote:
> However having prodded further I'm seeing incorrect key parsing with
> the omap-keypad driver under both -rc2 and -rc3 (works fine in
> 2.6.18-omap1). Numerous keys now returns strings of characters rather
> than the single expected character. A few keys still work as expected
> however. Before I dig in further is anyone else seeing anything similar?

This appears to be due to the addition of keymapsize to the
omap_kp_platform_data structure. The patch below fixes things up for
the Delta; other boards appear to have already had this done.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

More GPIO/IRQ cleanup:

  - compile-time removal of much useless code
      * mpuio support on non-OMAP1.
      * 15xx/730/24xx gpio support on 1610
      * 15xx/730/16xx gpio support on 24xx
      * etc

  - remove all BUG() calls, which are always bad news ... replaced some
    with normal fault reports for that call, others with WARN_ON(1).

  - small mpuio bugfix:  add missing set_type() method

Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Minor GPIO cleanups:  remove needless #include, and omap_gpio_init()
should be __init, as well as all the board init code calling it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.

If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmz71 specific things - board file.
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables some clock on omap310.
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPMC updates:
 - bugfixes: wrong/missing flags, omitted write, wrong test
 - don't map memory segments starting at zero
 - improve debug messaging
 - export gpmc_get_fclk_perio]d() since it's needed to calc timings
 - expect gpmc_cs_set_timings() caller to have initialized sync vs async

Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some OMAP 24xx pin mux declarations to support:

 - TUSB 6010 EVM (on H4)
 - All three full speed USB ports
 - GPIOs used with USB0 on Apollon and H4

For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove some conflicting declarations in omap2/memory.c so that the
file builds again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add some GPIO debug support:  /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.

Includes minor bugfixes:  recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In previous GPMC patch, there was a typo. Fix typo and add header files for
set_irq_type() warnings.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable serial idling and wakeup features
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Useful for debugging power management code.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable 24xx GPIO autoidling
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add DMA IRQ sanity checks
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Place SMS and SDRC into smart idle mode
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix warning:

arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void

Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix the following compiler warning (only visible with
CONFIG_OMAP_RESET_CLOCKS):

arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

.. hopefully most of the fallout of the timer changes is contained now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The watchdog implementation excludes low res / non continuous
clocksources from being selected as a watchdog reference
unintentionally.

Allow using jiffies/PIT as a watchdog reference as long as no better
clocksource is available. This is necessary to detect TSC breakage on
systems, which have no pmtimer/hpet.

The main goal of the initial patch (preventing to switch to highres/nohz
when no reliable fallback clocksource is available) is still guaranteed
by the checks in clocksource_watchdog().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The rework of next_timer_interrupt() fixed the timer wheel bugs, but
invented a rounding error versus the next hrtimer event. This is caused
by the conversion of the hrtimer internal representation to relative
jiffies.

This causes bug #8100:
http://bugzilla.kernel.org/show_bug.cgi?id=8100

next_timer_interrupt() returns "now" in such a case and causes the code
in tick_nohz_stop_sched_tick() to trigger the timer softirq, which is
bogus as no timer is due for expiry. This results in an endless context
switching between idle and ksoftirqd until a timer is due for expiry.

Modify the hrtimer evaluation so that, it returns now + 1, when the
conversion results in a delta < 1 jiffie.

It's confirmed to resolve bug #8100
Reported-by: Emil Karlson <jkarlson@cc.hut.fi>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4278/1: configure pxa27x I2C SCL as "input"
  [ARM] 4272/1: Missing symbol h1940_pm_return fix
  [ARM] 4235/1: ns9xxx: declare the clock functions as "const"
  [ARM] 4271/1: iop32x: fix ep80219 detection (support iq80219 platforms)
  [ARM] 4270/2: mach-s3c2443/irq.c off by one error in dma irqs

This is just a QA / cosmetic fix ..

[ "a modules" => "a module" ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After dvb tuner refactoring, the pllbuff has been altered such that the pll
address is now stored in buf[0].  Instead of sending buf to set_pll_input,
we should send buf+1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ivan Andrewjeski <ivan@fiero-gt.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It has been reported by Julian Deng that configuring the pxa27x i2c SCL line as output generates a short negative pulse on it during the call to pxa_gpio_mode(GPIO117_I2CSCL_MD); as it first switches it to output and then configures it for the alternate function. The SCL line is in fact bidirectional and can also be configured as 117 | GPIO_ALT_FN_1_IN, in which case the pulse is not generated. This is exactly what this patch does.

Author: Julian Deng <dengtj@sitek.cn>
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

commit f9690982 removed the check for
cpu_khz from sched_clock(), which prevented early access to the TSC by
non obvious magic.

This is harmless as long as the CPU has a TSC. On TSCless systems this
results in an illegal instruction trap.

Replace tsc_disabled and tsc_unstable by tsc_enabled, which is only set
when the tsc is available and not unstable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

  CC      arch/mips/mm/cerr-sb1.o
arch/mips/mm/cerr-sb1.c: In function 'sb1_cache_error':
arch/mips/mm/cerr-sb1.c:235: warning: format '%010llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_ic':
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llX' expects type 'long long unsigned int', but argument 6 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_dc':
arch/mips/mm/cerr-sb1.c:523: warning: format '%010llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:523: warning: format '%016llX' expects type 'long long unsigned int', but argument 7 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:570: warning: format '%016llX' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
  LD      arch/mips/mm/built-in.o
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/jazz/jazzdma.c:70: warning: assignment makes integer from pointer without a cast
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>