- 30 Mar, 2009 40 commits
-
-
Hans Verkuil authored
Bt819 needs the parent driver to drive a GPIO pin low and high in order to reset its fifo. Use the new notify callback for this. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
Add a notify callback to v4l2_device to let sub-devices notify their parent of special events. Signed-off-by:
-
Hans Verkuil authored
Normally the parent device of v4l2_device is used as the video device node's parent. But if it was not set, then use the parent field in the video_device struct. This is needed in the cx88 driver, which has one core v4l2_device but creates multiple pci devices (one each for raw and mpeg video). So you cannot associate the core v4l2_device with a particular PCI device, but you can do that for each video_device. Signed-off-by:
-
Hans Verkuil authored
The new support for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI board broke the existing boards. Interrupts for the netup part were enabled and handled without testing whether the current board actually had a netup -> instant and fatal crash. I've added tests to do this only for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI board. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Theodore Kilgore authored
Fix a bug where all frame headers were being discarded, instead of being part of the stream output, on MR97310A cameras. The frame headers contain information which may be useful in processing the video output and therefore should be kept and not discarded. A corresponding patch to the decompression algorithm in libv4lconvert/mr97310a.c corrects the change in frame offset. Signed-off-by:
Theodore Kilgore <kilgota@auburn.edu> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Michael Krufky authored
Setting state->frontend.demodulator_priv to NULL in the event of a kzalloc error will result in an OOPS. Just remove that line. Thanks to Matthias Schwarzott for pointing this out. Cc: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Hans Verkuil authored
If the i2c sub-device cannot be found, then we must unregister the i2c_client. Otherwise this will prevent a possible probe for a different device on that same address. Signed-off-by:
-
Hans Verkuil authored
Emphasize the need to call i2c_set_adapdata and clarify the use of the chipid in v4l2_i2c_new_(probed_)device(). Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Michael Krufky authored
We'll start off with MODULE_VERSION("0.1") Signed-off-by: -
Michael Krufky authored
small whitespace cleanup - space missing after the * Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
size_t should be printed with %zu. Signed-off-by:
-
Alexey Klimov authored
Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The vfl_type field is set by the core, so anything you fill in here will be overwritten. And it will be set to a VFL_TYPE_ value, not a VID_TYPE_ value which is an obsolete V4L1 type. Since these V4L1 types have been made unavailable for V4L2 drivers, this driver stopped compiling. In this case the fix is just removing this assignment. Cc: Sakari Ailus <sakari.ailus@nokia.com> Signed-off-by:
-
Hans Verkuil authored
This include isn't needed and so can be removed. Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Sri Deevi authored
Signed-off-by:
Srinivasa Deevi <srinivasa.deevi@conexant.com> Signed-off-by:
-
Stephan Wienczny authored
This patch adds support for Terratec Cinergy HT PCI MKII with card id 79. Its more or less a copy of Pinnacle Hybrid PCTV. Thanks to k1ngf1sher on forum.ubuntuusers.de for the idea to copy that card. Signed-off-by:
Stephan Wienczny <stephan@wienczny.de> Signed-off-by:
-
Matthias Schwarzott authored
Print a message in case the new software IRQ watchdog detects a problem. I choose the info message category, this can be changed if not appropriate. Cc: Patrick Boettcher <patrick.boettcher@desy.de> Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Scott James Remnant authored
The videodev module is missing the char-major-81-* alias that would cause it to be auto-loaded when a device of that type is opened. This patch adds the alias. Signed-off-by:
Scott James Remnant <scott@canonical.com> Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
-
Alexey Klimov authored
Patch fixes double mutex unlocking. Signed-off-by:
-
Martin Fuzzey authored
Call pwc_construct before trying to talk to device to obtain vc interface so that LED and power setup works the first time the video device is opened. Signed-off-by:
Martin Fuzzey <mfuzzey@gmail.com> Signed-off-by:
-
Robert Millan authored
My BTTV_BOARD_CONCEPTRONIC_CTVFMI2 card wasn't auto-detected, here's a patch that adds its PCI id. lspci -nnv output: 05:06.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11) 05:06.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11) Press <break> within 3 seconds if this is wrong. Signed-off-by: -
Jean Delvare authored
When unloading the cx8800 driver I sometimes get a general protection fault. Analysis revealed a race in cx88_ir_stop(). It can be solved by using a delayed work instead of a timer for infrared input polling. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Jean Delvare authored
The removal of the timer which polls the infrared input is racy. Replacing the timer with a delayed work solves the problem. Signed-off-by:
-
Jean Delvare authored
The removal of the timer which polls the infrared input is racy. Replacing the timer with a delayed work solves the problem. Signed-off-by:
-
Jean Delvare authored
The removal of the timer which polls the infrared input is racy. Replacing the timer with a delayed work solves the problem. Signed-off-by:
-
Trent Piepho authored
It reduces the size of the driver over all, and the function names in strings need to be manually kept up to date while __func__ doesn't. Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
-
Trent Piepho authored
Many functions had a struct file pointer argument, but all they wants is the struct zoran_fh pointer from the file's private data. Since every caller of those functions already has the zoran_fh, just pass the that instead. This saves a dereference in each function change. While I'm at it, change the code formatting of affected functions to be kernel standard style. Signed-off-by:
-
Jean Delvare authored
kmalloc() can fail for large video buffers. By default the kernel complains loudly about allocation failures, but we don't want to frighten the user, so ask kmalloc() to keep quiet on such failures. Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Jean Delvare authored
The lock_norm module parameter doesn't look terribly useful. If you don't want to change the norm, just don't change it. As a matter of fact, no other v4l driver has such a parameter. Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Trent Piepho authored
The zoran driver had two kinds of buffer descriptors, one for jpg buffers and one for raw buffers. They were mostly the same with only a couple Signed-off-by: -
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
replace occurances of "HVR1150" with "HVR1120" - this was a typo. Signed-off-by:
-
Hans Verkuil authored
There are no drivers left that call msp3400 with V4L1 commands. Remove it from this driver. Signed-off-by:
-
