- 27 Oct, 2009 36 commits
-
-
Reinette Chatre authored
The sleep_level_override debugfs file is used by the user to request a static power index instead of the dynamic sleep values. Users are expected to provide value from 1 to 5 as an index or -1 to disable it. The problem at the moment is that users can also provide 0 to this file which, together with the value 1, is translated to index 1. This is confusing and even more so when users write 0 to sleep_level_override and then read 1 from it afterwards. Modify checking to treat 0 as invalid. Signed-off-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Add more items to sensitivity range table to avoid using hardcoded values. Initialize the table per device since unique per device information is required to perform sensitivity calibration. additional items in sensitivity range table: .barker_corr_th_min: Barker correlation threshold minimum .barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC .nrg_th_cca: Energy threshold for Clear Channel Assessment Barker codes are a technique used in WLAN encoding for transmission. MRC is "Maximal Ratio Combining", a technique for optimally combining the signals from 2 or more receivers to achieve a better signal. Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
"IWL_CMD_QUEUE_NUM" is being defined in multiple places and used by all the devices. move it to iwl-dev.h file and shared by all the devices. Remove "IWL_CMD_FIFO_NUM", replaced by "IWL49_CMD_FIFO_NUM" and IWL50_CMD_FIFO_NUM" Signed-off-by:
-
Ben Cahill authored
Clean up device-specific apm_reset() functions and library infrastructure, now that these reset() functions are no longer being used. Signed-off-by:
Ben Cahill <ben.m.cahill@intel.com> Signed-off-by:
-
Ben Cahill authored
Now that we're unconditionally using apm_ops.stop() to reset and power-down the device in __iwl3945_down(), the apm_ops.reset() is redundant. Removing this call will also allow us to remove iwl3945_apm_reset(). Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other following calls. Signed-off-by:
-
Ben Cahill authored
In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user no longer wants device active), device has not been going into low power state via __iwl_down(). apm_ops.reset() does not put device into low power state; instead it resets the device, then puts it into a powered-up state ready to be re-loaded with uCode and re-started. This has needlessly warmed up user's laptops and drained batteries. With current architecture in which mac80211 controls device up/down (including resetting device after firmware errors), there is no need for apm_ops.reset() any more; apm_ops.reset() is basically a combination of apm_ops.stop() and apm_ops.init(). Instead, __iwl_down() now unconditionally places the device into a low-power state via apm_ops.stop(). Device may be re-started via __iwl_up() calling apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors), but in the meantime, device will stop wasting energy. Note that, even in this low power state, if driver re-enables interrupts, the device retains the ability to sense the hardware RF-KILL switch, and (except for 3945) interrupt the host when it changes. Signed-off-by:
-
Ben Cahill authored
Update iwl3945_apm_init() to set up device registers in sequence most recently recommended by factory. Add resets for APMG interrupts and radio chip, formerly done only in iwl3945_apm_reset(); moving them here assures that apm_init() will do a complete job of preparing hardware not only after platform boot, but also after apm_stop() has executed (due to rfkill, ifconfig down, driver unload, etc.). This is in preparation to completely remove apm_reset(). Add some comments. Signed-off-by:
-
matthieu castet authored
Some airo card don't support power Management [1]. Don't abort suspend with those cards. 00:06.0 Network controller: AIRONET Wireless Communications PC4800 (rev 01) Flags: medium devsel, IRQ 17 Memory at dffffe00 (32-bit, non-prefetchable) [size=128] I/O ports at d000 [size=128] I/O ports at cc00 [size=64] Kernel driver in use: airo Signed-off-by:Matthieu CASTET <castet.matthieu@free.fr> Signed-off-by:
-
Michael Buesch authored
Remove me Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
-
Michael Buesch authored
This slightly shrinks the structure. Signed-off-by:
-
Michael Buesch authored
We must check the bustype before using the host_pci pointer. Signed-off-by:
-
Sujith authored
When TX is hung, the chip is reset. Ensure that the chip is awake by using the PS wrappers. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Amitkumar Karwar authored
Return status of lbs_prepare_and_send_command and lbs_cmd_with_response functions is not checked at some places. Those checks are added. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Acked-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Juuso Oikarinen authored
Currently several events are enabled from the firmware for which there is no handling. This wakes up the host unnecessarily. Mask those unneeded events. Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
Enable beacon filtering when PSM is enabled Signed-off-by:
-
Juuso Oikarinen authored
Enable beacon filtering with the mac80211 stack. Signed-off-by:
-
Juuso Oikarinen authored
Add configuration for connection monitor (number of allowed beacons, and timeout after last received beacon.) Signed-off-by:
-
Juuso Oikarinen authored
Use vmalloc to allocate memory for the firmware image, and use a smaller linear buffer for the actual transfer of the firmware to the chipset. This patch is an adaptation of a similar patch for wl1251 by Kalle Valo. Signed-off-by:
-
Juuso Oikarinen authored
Enable multicast filtering. This way by default no multicast frames will reach the host, and when needed, only required multicast frames can be passed from the WLAN chipset to the host. Signed-off-by:
-
Juuso Oikarinen authored
Clear the probe-request template on the firmware after scan. Unless cleared, the firmware can independently send probe requests to the AP and interfere with the mac80211 logic. Signed-off-by:
-
Juuso Oikarinen authored
Use the workqueue provided by the mac80211 stack instead of the system default queue. Modified to use new ieee_queue_work() as required by changes in the stack. Signed-off-by:
-
Luciano Coelho authored
This is a hack to disable all filters in the join command. This is based on Kalle Valo's patch for wl1251. Cc: Kalle Valo <kalle.valo@nokia.com> Signed-off-by:
-
Luciano Coelho authored
Add Juuso as one of the module authors, since he's working heavily on this module as well. Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by:
-
Juuso Oikarinen authored
Corrections to the TX path - use correct number of maximum descriptors (32 instead of 16) and correct checking and setting of excessive retries on completion. Signed-off-by:
-
Juuso Oikarinen authored
Update the usage of join's, including using actual beacon interval and dtim from AP, and configuring a basic rate set from AP. Signed-off-by:
-
Juuso Oikarinen authored
Configure the rate policies to the firmware based on the rates given by the AP. Signed-off-by:
-
Juuso Oikarinen authored
This patch adds implementation for checking for SPI busy words - i.e. honoring a delay request from the WLAN chipset upon reading registers/memory. To optimized the average SPI ready by 32 bits, also configure the number of busywords to one to disable the "fixed-busy-word" functionality. Signed-off-by:
Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
In ps-poll template aid bits 14 and 15 were not masked as required by the standard. Mask them so that aid is sent in correct format. This patch is a direct port of the respective patch for the wl1251 driver by Kalle Valo. Signed-off-by:
-
Juuso Oikarinen authored
Implement delayed entry into ELP. This will promote the following: - Less redundant sleep/wake cycles (better perf) - Avoids known firmware issues with going to ELP too fast after an operation Signed-off-by:
-
Juuso Oikarinen authored
Correct the position to which TKIP header space is appended for TX packets. Signed-off-by:
-
Juuso Oikarinen authored
Add security sequence number handling to the driver TX data path needed by WPA. Signed-off-by:
Kalle Valo <kalle.valo@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
Correct the TX path implementation to allocate sufficient blocks in the firmware for TX packets. Signed-off-by:
-
Luciano Coelho authored
The qual element in ieee80211_rx_status is not used anymore, so we don't need to set it in the wl1271_rx_status() function. This saves a bit of time in the RX path. Signed-off-by:
-
David Kilroy authored
Signed-off-by:
David Kilroy <kilroyd@googlemail.com> Signed-off-by:
-
Luis R. Rodriguez authored
The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during reset or initial calibration, update the PA calibration to account for that and initialize PA calibration variables for both conditions. Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
Luis R. Rodriguez authored
This is required for the ar9271 hardware as well. Signed-off-by:
-
- 24 Oct, 2009 4 commits
-
-
Ben Hutchings authored
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs, covering both more and less than XFP. Rename its functions and constants to reflect reality and to reduce namespace pollution when sfc is a built-in driver. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ben Hutchings authored
The only multi-speed PHY driver using this is 10Xpress, and it does not support non-autoneg operation. Signed-off-by:
-
Ben Hutchings authored
efx_fc_resolve() is specific to MDIO and is not used by any other function. Signed-off-by:
-
Ben Hutchings authored
The MTD partition is named based on the netdev name, which is set to 'eth%d' before registration. Also, the MTD partition will currently be left registered if netdev registration fails. Fix both these problems by moving the MTD probe after netdev registration. Hold the RTNL to serialise this with the netdev notifier that calls efx_mtd_rename(). Signed-off-by:
-
