Signed-off-by: Kevin Hilman <khilman@mvista.com>

Remove OSK/Mistral and Innovator support for the old OMAP-specfic
touchscreen framework; both of those board should be able to use
the new SPI framework with the ads7846 touchscreen driver that's
now in the upstream kernels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Add bitbang SPI driver for Innovator 1510 touchscreen, using the new
framework.  Compile-tested only.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

The device is using a protocoll where writes are on the falling, reads are
on the rising edge of the clock. This maps to SPI mode 1.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

SPI mode 0 maps to the case where we have write on rising and read on
falling clock edge. Fix the OMAP2 McSPI and OMAP1 uWire edge selection
accordingly.

In the uWire case the meaning of the HW flag selecting the read edge
selection must be flipped for correct operation and this is in
contradiction with the OMAP1 specification. Tests were performed on SPI
devices using mode 1 (original uWire protocoll) like the ads7846 to
validate this.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix for channel reconfiguration case: once the EPOL, POL or PHA has been
configured to 1, further configuration on the channel can't change it to 0.

The first CS enable is not needed. The CS will be enabled right before
the transfer anyway, if it's not active.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I can't see any reason why OMAP_GPIO_SWITCH depends on OMAP_BOOT_TAG;
it compiles fine without it. This patch removes the Kconfig dependency.

Here's an updated patch that not only removes the dependency but cleans
up the Kconfig description to talk about sysfs rather than the input
layer.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Paul Mundt <paul.mundt@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add platform driver init-code required by the aic23-alsa driver to
omap-innovator.
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Do not try to change the clockrate if it is already ok. This fixes the
driver for omap-innovator which uses fixed clockrate.
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I2C and I2C-OMAP must be built if aic23 driver is built.
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO IRQ mask was retrieved incorrectly in cases where we have a mask
register instead of an enable register. Also we should only return the
valid bits depending on the bank size.

This fixes a bug on 1510/1610 based OMAPs where GPIO IRQs are not
delivered.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix for re-using OMAP DMA channel with different transfer parameters.
Bits in the CCR register need to be cleaned as well in some cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is an updated version of my patch that adds support for RGB444 mode
for the internal LCD controller which now applies against linux-2.6.16
with the patch-2.6.16-omap2 applied.

Jonathan McDowell posted a slightly modified version of my original patch
to this list previously:

http://Linux.omap.com/pipermail/linux-omap-open-source/2006-April/006839.html

This patch is used by the Amstrad Delta (E3).
Signed-off-by: Mark Underwood <basicmark@yahoo.com>
Acked-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mixing "depends on I2C" and "select I2C" within the media subsystem
leads to the following problem:
Warning! Found recursive dependency: I2C DVB_BUDGET DVB_BUDGET_PATCH
DVB_AV7110 VIDEO_SAA7146_VV VIDEO_SAA7146 I2C
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: deref correct pointer when using kernel SMA
  IB/ipath: fix null deref during rdma ops
  IB/ipath: register as IB device owner
  IB/ipath: enable PE800 receive interrupts on user ports
  IB/ipath: enable GPIO interrupt on HT-460
  IB/ipath: fix NULL dereference during cleanup
  IB/ipath: replace uses of LIST_POISON
  IB/ipath: fix reporting of driver version to userspace
  IB/ipath: don't modify QP if changes fail
  IB/ipath: fix spinlock recursion bug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
  JFS: Fix multiple errors in metapage_releasepage

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] libata: add pio flush for via atapi (was: Re: TR: ASUS A8V Deluxe, x86_64)

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] sky2: fix jumbo packet support

md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

It looks like metapage_releasepage was making in invalid assumption that
the releasepage method would not be called on a dirty page.  Instead of
issuing a warning and releasing the metapage, it should return 0, indicating
that the private data for the page cannot be released.

I also realized that metapage_releasepage had the return code all wrong.  If
it is successful in releasing the private data, it should return 1, otherwise
it needs to return 0.

Lastly, there is no need to call wait_on_page_writeback, since
try_to_release_page will not call us with a page in writback state.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>

Backport the "pio flush" from the libata major update to 2.6.17 for via atapi.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Bridge will OOPS on removal if other application has the SAP open.
The bridge SAP might be shared with other usages, so need
to do reference counting on module removal rather than explicit
close/delete.

Since packet might arrive after or during removal, need to clear
the receive function handle, so LLC only hands it to user (if any).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If kmalloc fails, error path leaks data allocated from asn1_oid_decode().
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When parsing unknown sequence extensions the "son"-pointer points behind
the last known extension for this type, don't try to interpret it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The condition "> H323_ERROR_STOP" can never be true since H323_ERROR_STOP
is positive and is the highest possible return code, while real errors are
negative, fix the checks. Also only abort on real errors in some spots
that were just interpreting any return value != 0 as error.

Fixes crashes caused by use of stale data after a parsing error occured:

BUG: unable to handle kernel paging request at virtual address bfffffff
 printing eip:
c01aa0f8
*pde = 1a801067
*pte = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: ip_nat_h323 ip_conntrack_h323 nfsd exportfs sch_sfq sch_red cls_fw sch_hfsc  xt_length ipt_owner xt_MARK iptable_mangle nfs lockd sunrpc pppoe pppoxx
CPU:    0
EIP:    0060:[<c01aa0f8>]    Not tainted VLI
EFLAGS: 00210646   (2.6.17-rc4 #8)
EIP is at memmove+0x19/0x22
eax: d77264e9   ebx: d77264e9   ecx: e88d9b17   edx: d77264e9
esi: bfffffff   edi: bfffffff   ebp: de6a7680   esp: c0349db8
ds: 007b   es: 007b   ss: 0068
Process asterisk (pid: 3765, threadinfo=c0349000 task=da068540)
Stack: <0>00000006 c0349e5e d77264e3 e09a2b4e e09a38a0 d7726052 d7726124 00000491
       00000006 00000006 00000006 00000491 de6a7680 d772601e d7726032 c0349f74
       e09a2dc2 00000006 c0349e5e 00000006 00000000 d76dda28 00000491 c0349f74
Call Trace:
 [<e09a2b4e>] mangle_contents+0x62/0xfe [ip_nat]
 [<e09a2dc2>] ip_nat_mangle_tcp_packet+0xa1/0x191 [ip_nat]
 [<e0a2712d>] set_addr+0x74/0x14c [ip_nat_h323]
 [<e0ad531e>] process_setup+0x11b/0x29e [ip_conntrack_h323]
 [<e0ad534f>] process_setup+0x14c/0x29e [ip_conntrack_h323]
 [<e0ad57bd>] process_q931+0x3c/0x142 [ip_conntrack_h323]
 [<e0ad5dff>] q931_help+0xe0/0x144 [ip_conntrack_h323]
...

Found by the PROTOS c07-h2250v4 testsuite.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point, the core QP structure hasn't been initialized, so what's
in there isn't valid.  Get the same information elsewhere.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The problem was that node A's sending thread, which handles sending RDMA
read response data, would write the trigger word, the last packet would
be sent, node B would send a new RDMA read request, node A's interrupt
handler would initialize s_rdma_sge, then node A's sending thread would
update s_rdma_sge.  This didn't happen very often naturally but was more
frequent with 1 byte RDMA reads.  Rather than adding more locking or
increasing the QP structure size and copying sge data, I modified the
copy routine to update the pointers before writing the trigger word to
avoid the update race.
Signed-off-by: Ralph Campbell <ralphc@pathscale.com>
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This fixes an oops.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fixed so it works on the PE-800.  It had not previously been updated to
match PE-800 receive interrupt differences from HT-400.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This is required for even semi-decent performance on OpenIB.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix NULL deref due to pcidev being clobbered before dd->ipath_f_cleanup()
was called.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Per Andrew's request.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Fix the interface version that gets exported to userspace.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Make sure modify_qp won't modify the QP if any of the changes failed.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

The local loopback path for RC can lock the rkey table lock without
blocking interrupts.  The receive interrupt path can then call
ipath_rkey_ok() and deadlock.  Remove the redundant lock.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>