Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes.  Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.

This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.

Cc: stable@kernel.org
Signed-off-by: Lorenzo Nava <navalorenx@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates p54's Kconfig entry and removes the out-dated device list.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes mac80211 to not notify the rate control algorithm's
tx_status() method when reporting status for a packet that didn't go
through the rate control algorithm's get_rate() method.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch simplifies the tx_status report code by using four tx_queues per
station instead of only one. (the skb lookup should be in O(1) now :-p ).

Also, it fixes a really obvious copy&paste bug in the janitor work code and
adds back a few spilled bits to the hardware definition header about QoS.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add IEEE80211_HW_BEACON_FILTERING flag so that driver inform that it supports
beacon filtering. Drivers need to call the new function
ieee80211_beacon_loss() to notify about beacon loss.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In beacon filtering there needs to be a way to not expire the BSS even
when no beacons are received. Add an interface to cfg80211 to hold
BSS and make sure that it's not expired.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When software scanning we need to disable power save so that all possible
probe responses and beacons are received. For hardware scanning assume that
hardware will take care of that and document that assumption.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Separate beacon and rx path tracking in preparation for the beacon filtering
support. At the same time change ieee80211_associated() to look a bit simpler.

Probe requests are now sent only after IEEE80211_PROBE_IDLE_TIME, which
is now set to 60 seconds.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the timer is triggering every two seconds
(IEEE80211_MONITORING_INTERVAL). Decrease the timer to only trigger during
data idle periods to avoid waking up CPU unnecessary. The timer will
still trigger during idle periods, that needs to be fixed later.

There's also a functional change that probe requests are sent only when the
data path is idle, earlier they were sent also while there was activity
on the data path.

This is also preparation for the beacon filtering support. Thanks to
Johannes Berg for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add vendor ID for Quanta Microsystems and update the led table with the reported device.
Reported-by: Scott Barnes <nekoreeve@gmail.com>
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch update all necessary Makefile and Kconfig files.

Now you can then enable ar9170 in the kernel configuration under:
Device Drivers --->
	[*] Network device support --->
		Wireless LAN --->
			[*] Wireless LAN (IEEE 802.11)
			<M>   Atheros AR9170 support
			<M>     Atheros AR9170 USB support
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

USB frontend driver code for Atheros' AR9170 modules.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAC/BBP and PHY programming code
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch contains almost all mac80211 interaction code of AR9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hardware / firmware interface definitions for Atheros' AR9170 based devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We had left in code to allow interested developers to add
support for parsing country IEs when OLD_REG was enabled.
This never happened and since we're going to remove OLD_REG
lets just remove these comments and code for it.

This code path was never being entered so this has no
functional change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It seems a few users are using this module parameter although its not
recommended. People are finding it useful despite there being utilities
for setting this in userspace. I'm not aware of any distribution using
this though.

Until userspace and distributions catch up with a default userspace
automatic replacement (GeoClue integration would be nirvana) we copy
the ieee80211_regdom module parameter from OLD_REG to the new reg
code to help these users migrate.

Users who are using the non-valid ISO / IEC 3166 alpha "EU" in their
ieee80211_regdom module parameter and migrate to non-OLD_REG enabled
system will world roam.

This also schedules removal of this same ieee80211_regdom module
parameter circa March 2010. Hope is by then nirvana is reached and
users will abandoned the module parameter completely.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The incorrect assumption is the last regulatory request
(last_request) is always a country IE when processing
country IEs. Although this is true 99% of the time the
first time this happens this could not be true.

This fixes an oops in the branch check for the last_request
when accessing drv_last_ie. The access was done under the
assumption the struct won't be null.

Note to stable: to port to 29 replace as follows, only 29 has
country IE code:

s|NL80211_REGDOM_SET_BY_COUNTRY_IE|REGDOM_SET_BY_COUNTRY_IE

Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Although EU is a bogus alpha2 we need to process the send request
as our code depends on last_request being set.

Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Without this the regulatory domain isn't seen and we end up
intersecting for each request (each radio).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables mesh point operation for ath9k.  Tested with b43,
ath9k, rt2500usb, and ath5k as peers.
Signed-off-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a compile problem when the MAC80211_LEDS
triggers are enabled but not LED class itself.
(which is sort of pointless, but anyway...)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.

Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb is not experimental anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This file was forgotten from the quilt patch that added MLME
primitives, so the kfree on interface removal is missing. Fix this
potential memleak by freeing the temporary Authentication frame IEs
from SME when the interface is being removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates count of every hw tried rate with
appropriate tries before reporting tx status of a frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When mac80211 resumes, it currently doesn't reconfigure the interfaces
entirely and also doesn't reconfigure BSS information -- fix this.

Also, to be able to test this, add a debugfs file that just calls
the suspend/resume code to see what happens when we go through that,
without needing the time-consuming suspend/resume cycle.

(Original version broke the build for CONFIG_PM=n.  Define alternative
functions for that situation. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This masks the PHY TX error interrupt, if debugging is disabled.

Currently we have a bug somewhere which triggers this interrupt once
in a while. (Depends on the network noise/quality). While this is nonfatal,
it scares the hell out of users and we frequently receive bugreports
that incorrectly identify this error message as the reason.

There's another problem with this. The PHY TX error interrupt is protected
with a watchdog that will restart the device if it keeps triggering very often.
This is used to fix interrupt storms from completely broken devices.

However, this watchdog might trigger in completely normal operation.
If the TX capacity of the card is saturated, the likeliness of the watchdog
triggering increases, as more TX errors occur. The current threshold
for the watchdog is 1000 errors in 15 seconds.

This patch adds a workaround for the issue by just enabling the interrupt
if debugging is disabled (by Kconfig or by modparam).

This has the downside that real fatal PHY TX errors are not caught anymore.
But this is nonfatal due to the following reasons:
* If the card is not able to transmit anymore, MLME will notice anyway.
* I did _never_ see a real fatal PHY TX error in a mainline b43 driver.
* It does _not_ result in interrupt storms or something like that.
  It will simply result in a stalled card. It can be debugged by enabling
  the debugging module parameter.
Signed-off-by: Michael Buesch <mb@bu3sch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

m68k allmodconfig:
| drivers/net/wireless/p54/p54spi.c: In function 'p54spi_probe':
| drivers/net/wireless/p54/p54spi.c:675: error: implicit declaration of function
| 'set_irq_type'
| make[4]: *** [drivers/net/wireless/p54/p54spi.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.

The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).

The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.

The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.

This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.

This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We must not clear the previous BSSID when roaming to another AP within
the same ESS for reassociation to be used properly. It is fine to
clear this when the SSID changes, so let's move the code into
ieee80211_sta_set_ssid().
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>