Generated with the following semantic patch

@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)

@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)

applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define name tables for these enumerations in a similar way as for
loopback.  Move the loopback name table together with them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All files that include ethtool.h, rx.h or tx.h are also including
efx.h, and there is no good reason to separate out the few
declarations they contain.  Therefore fold them into efx.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At some point these casts were used to remove const qualification, but
they are now unneeded.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is preparation for moving Falcon-specific state required by other
Falcon-specific code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename struct efx_board to struct falcon_board.

Introduce and use inline function to look up board info from struct
efx_nic, in preparation for moving it.

Move board init and fini calls into NIC probe and remove functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

efx_board::init_leds was introduced as a second stage of
initialisation because of the inter-dependency between the board and
PHY.  We want to move board initialisation into NIC probing, which is
too early to use MDIO, so SFN4111T initialisation also needs to be
split.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only some PHYs have firmware support for a LED blink mode, so we
currently blink the others in a timer function.  Since all PHYs have
simple on and off modes, we don't gain anything by using multiple
blink implementations.  Also, since we have a process context there
is no need to use a timer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes the need to use a label and goto, and makes the two
branches mirror each other more closely.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function no longer has any common cleanup code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Finish the job by removing the structure member.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Copied from original one-line patch here:

	http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26

(This is for 2.6.33 and beyond, where the bool was changed to a flag by
"cfg80211: convert bools into flags". -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The range check in the sprom image parser hex2sprom() is broken.
One sprom word is 4 hex characters.
This fixes the check and also adds much better sanity checks to the code.
We better make sure the image is OK by doing some sanity checks to avoid
bricking the device by accident.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The SPROM writing routines were broken since we rewrote the suspend
handling on wireless devices, because SPROM writing depended on suspend.

This patch changes it and freezes devices with the driver remove(), probe()
callbacks instead. This also simplifies the whole logics a lot.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Stall workaround doesn't work with bcm4320a devices like with bcm4320b.
This workaround actually causes more stalls/device freeze on bcm4320a.
Therefore disable stall workaround by default.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_query_oid overwrites *len which stores buffer size to return full size
of received command and then uses *len with memcpy to fill buffer with
command.

Ofcourse memcpy should be done before replacing buffer size.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix the following htmldocs warnings:

  Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
  Warning(net/mac80211/sta_info.h:322): No description found for parameter 'drv_unblock_wk'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Current blinking rate is calculated based on the difference between
current tx/rx byte counts and priv->led_tpt.

priv->led_tpt should not get reset in iwl_leds_init(), this function can be
called by bring interface "up" or "down", or when uCode sysassert occurred.
resetting the led_tpt parameter will introduce incorrect led blinking behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change error message for command queue full
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.

Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags.  This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.

Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For "sram" debugfs file, if user did not specify the offset and length,
dump the entire data portion of sram by default.
Data portion is 0x800000 - 0x80ffff, but the actual data size is known
to the driver from the ucode file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.

Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

reserved2 field in "struct iwl4965_addsta_cmd" is __le16.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Dynamically allocate memory for dumping SRAM based on the length of memory
to be displayed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.

Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>