Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2
interfaces) and FT4232H (4 interfaces), including a new baud rate
calculation for these devices which can now achieve up to 12Mbaud by
turning off a divide by 2.5 in the baud rate generator of the chips.  In
order to achieve baud rates of <1200 baud, the divide by 2.5 must be
active.  The default product ID of the FT2232H is 0x6010 (same as the
FT2232C IC).  The default PID of the FT4232H is 0x6011.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Tested on OMAP3 host side with Creative (Live! Cam Optia) USB camera
which uses high bandwidth isochronous IN endpoints.  FIFO mode 4 is
updated to provide the needed 4K endpoint buffer without breaking
the g_nokia composite gadget configuration.  (This is the only
gadget driver known to use enough endpoints to notice the change.)
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

Currently, with Inventra DMA, we use Mode 0 if transfer size is less
than or equal to the endpoint's maxpacket size.  This requires that
we explicitly set TXPKTRDY for that transfer.

However the musb_g_tx code will not set TXPKTRDY twice if the last
transfer is exactly equal to maxpacket, even if request->zero is set.
Using Mode 1 will solve this; a better fix might be in musb_g_tx().

Without this change, musb will not correctly send out a ZLP if the
last transfer is the maxpacket size and request->zero is set.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Adjust HNP state machines in MUSB driver so that they handle the
case where the cable is disconnected.  The A-side machine was
very wrong (unrecoverable); the B-Side was much less so.

 - A_PERIPHERAL ... as usual, the non-observability of the ID
   pin through Mentor's registers makes trouble.  We can't go
   directly to A_WAIT_VFALL to end the session and start the
   disconnect processing.  We can however sense link suspending,
   go to A_WAIT_BCON, and from there use OTG timeouts to finally
   trigger that A_WAIT_VFALL transition.  (Hoping that nobody
   reconnects quickly to that port and notices the wrong state.)

 - B_HOST ... actually clear the Host Request (HR) bit as the
   messages say, disconnect the peripheral from the root hub,
   and don't detour through a suspend state.  (In some cases
   this would eventually have cleaned up.)

Also adjust the A_SUSPEND transition to respect the A_AIDL_BDIS
timeout, so if HNP doesn't trigger quickly enough the A_WAIT_VFALL
transition happens as it should.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Minor HNP bugfixes, so the initial role switch works:

 - A-Device:
     * disconnect-during-suspend enters A_PERIPHERAL state
     * kill OTG timer after reset as A_PERIPHERAL ...
     * ... and also pass that reset to the gadget
     * once HNP succeeds, clear the "ignore_disconnect" flag
     * from A_PERIPHERAL, disconnect transitions to A_WAIT_BCON

 - B-Device:
     * kill OTG timer on entry to B_HOST state (HNP succeeded)
     * once HNP succeeds, clear "ignore_disconnect" flag
     * kick the root hub only _after_ the state is adjusted

Other state transitions are left alone.  Notably, exit paths from
the "roles have switched" state ... A_PERIPHERAL handling of that
stays seriously broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Minor cleanup of OTG timer handling:
    * unify decls for OTG time constants, in the core header
    * set up and use that timer in a more normal way
    * move to the driver struct, so it's usable outside core

And tighten use and setup of T(a_wait_bcon) so that if it's used,
it's always valid.  (If that timer expires, the A-device will
stop powering VBUS.  For non-OTG systems, that will be a surprise.)
No behavioral changes, other than more consistency when applying
that core HNP timeout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated.  OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.

Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The NOP OTG transceiver driver needs to be usable from modules.
Make sure its symbols are always accessible at both compile and
link time, and make sure the device instance is allocated from
the heap so that device lifetime rules are obeyed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix a reporting glitch in the twl4030 USB transceiver code.
It wasn't properly distinguishing the two types of active
USB link:  ID grounded, vs not.  In the current code that
distinction doesn't much matter; in the future this bugfix
should help support better USB controller communications.

Provide a comment sorting out some of the cryptic bits of
the manual:  different sections use different names for
key signals, and the register definitions don't help much
without the explanations and diagrams.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A pointer to ehci_orion_drv_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Ronen Shitrit <rshitrit@marvell.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nicolas Pitre <nico@marvell.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tzachi Perelstein <tzachi@marvell.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A pointer to r8a66597_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A pointer to twl4030_usb_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As DaVinci DM646x has a dedicated CPPI DMA interrupt, replace
cppi_completion() (which has always been kind of layering
violation) by a complete CPPI interrupt handler.

[ dbrownell@users.sourceforge.net: only cppi_dma.c needs platform
device header, not cppi_dma.h ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As musb_advance_schedule() is now the only remaning
caller of musb_giveback() (and the only valid context
of such call), just fold the latter into the former
and then rename __musb_giveback() into musb_giveback().

This is a net minor shrink.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The argument for the 'is_in' parameter of musb_cleanup_urb()
is always extracted from an URB that's passed to the function.
So that parameter is superfluous; remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The existance of the scheduling list shouldn't matter in
determining whether there's currectly an URB executing on a
hardware endpoint. What should actually matter is the 'in_qh'
or 'out_qh' fields of the 'struct musb_hw_ep' -- those are
set in musb_start_urb() and cleared in musb_giveback() when
the endpoint's URB list drains. Hence we should be able to
replace the big *switch* statements in musb_urb_dequeue()
and musb_h_disable() with mere musb_ep_get_qh() calls...

While at it, do some more changes:

 - add 'is_in' variable to musb_urb_dequeue();

 - remove the unnecessary 'epnum' variable from musb_h_disable();

 - fix the comment style in the vicinity.

This is a minor shrink of source and object code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Factor out the often used code to get/set the active 'qh'
pointer for the hardware endpoint.  Change the way the case
of a shared FIFO is handled by setting *both* 'in_qh' and
'out_qh' fields of 'struct musb_hw_ep'.  That seems more
consistent and makes getting to the current 'qh' easy when
the code knows the direction beforehand.

While at it, turn some assignments into intializers and
fix declaration style in the vicinity.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Refactor musb_save_toggle() as follows:

 - replace 'struct musb_hw_ep *ep' parameter by 'struct
   musb_qh *qh' to avoid re-calculating this value 

 - move usb_settogle() call out of the *if* operator.

This is a net minor shrink of source and object code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Suppress "parasitic" endpoint interrupts in the DMA mode
when using CPPI DMA driver; they're caused by the MUSB gadget
driver using the DMA request mode 0 instead of the mode 1.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely.

The driver also prematurely leaves the status phase on
receiving the SetupEnd interrupt.

As there were still unhandled endpoint 0 interrupts happening
from time to time after fixing these issues, there turned to
be yet another culprit: two distinct gadget states collapsed
into one.

The (missing) state that comes after STATUS IN/OUT states was
typically indiscernible from them since the corresponding
interrupts tend to happen within too little period of time
(due to only a zero-length status packet in between) and so
they got coalesced; yet this state is not the same as the next
one which is associated with the reception of a SETUP packet.

Adding this extra state seems to have fixed the rest of the
unhandled interrupts that generic_interrupt() and
davinci_interrupt() hid by faking their result and only
emitting a debug message -- so, stop doing that.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the Toshiba HSDPA Minicard (which is just a
rebranded Novatel EU870D) used in some Toshiba laptops.

This is my first patch attempt, I hope I got the conventions right.
Signed-off-by: Michele Valzelli <valz@messagenet.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I would like to have added new device to usbserial/ftdi_sio driver.
These ids used USB track device (http://www.l-and-b.dk/access_alt.html).
They use differend device IDs, but it works as standard usb-serial
conventer.

From: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix compile error in arch/ia64/mm/extable.c

Merge branch 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timers: Logic to move non pinned timers
  timers: /proc/sys sysctl hook to enable timer migration
  timers: Identifying the existing pinned timers
  timers: Framework for identifying pinned timers
  timers: allow deferrable timers for intervals tv2-tv5 to be deferred

Fix up conflicts in kernel/sched.c and kernel/timer.c manually

Merge branch 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevent: export register_device and delta2ns
  clockevents: tick_broadcast_device can become static

Merge branch 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: prevent selection of low resolution clocksourse also for nohz=on
  clocksource: sanity check sysfs clocksource changes

Merge branch 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-for-linus-ntp' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ntp: fix comment typos
  ntp: adjust SHIFT_PLL to improve NTP convergence

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1244 commits)
  pkt_sched: Rename PSCHED_US2NS and PSCHED_NS2US
  ipv4: Fix fib_trie rebalancing
  Bluetooth: Fix issue with uninitialized nsh.type in DTL-1 driver
  Bluetooth: Fix Kconfig issue with RFKILL integration
  PIM-SM: namespace changes
  ipv4: update ARPD help text
  net: use a deferred timer in rt_check_expire
  ieee802154: fix kconfig bool/tristate muckup
  bonding: initialization rework
  bonding: use is_zero_ether_addr
  bonding: network device names are case sensative
  bonding: elminate bad refcount code
  bonding: fix style issues
  bonding: fix destructor
  bonding: remove bonding read/write semaphore
  bonding: initialize before registration
  bonding: bond_create always called with default parameters
  x_tables: Convert printk to pr_err
  netfilter: conntrack: optional reliable conntrack event delivery
  list_nulls: add hlist_nulls_add_head and hlist_nulls_del
  ...

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
  powerpc: Fix bug in move of altivec code to vector.S
  powerpc: Add support for swiotlb on 32-bit
  powerpc/spufs: Remove unused error path
  powerpc: Fix warning when printing a resource_size_t
  powerpc/xmon: Remove unused variable in xmon.c
  powerpc/pseries: Fix warnings when printing resource_size_t
  powerpc: Shield code specific to 64-bit server processors
  powerpc: Separate PACA fields for server CPUs
  powerpc: Split exception handling out of head_64.S
  powerpc: Introduce CONFIG_PPC_BOOK3S
  powerpc: Move VMX and VSX asm code to vector.S
  powerpc: Set init_bootmem_done on NUMA platforms as well
  powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
  powerpc/mm: Fix some SMP issues with MMU context handling
  powerpc: Add PTRACE_SINGLEBLOCK support
  fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
  powerpc/virtex: Add ml510 reference design device tree
  powerpc/virtex: Add Xilinx ML510 reference design support
  powerpc/virtex: refactor intc driver and add support for i8259 cascading
  powerpc/virtex: Add support for Xilinx PCI host bridge
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator/max1586: fix V3 gain calculation integer overflow
  regulator/max1586: support increased V3 voltage range
  regulator: lp3971 - fix driver link error when built-in.
  LP3971 PMIC regulator driver (updated and combined version)
  regulator: remove driver_data direct access of struct device
  regulator: Set MODULE_ALIAS for regulator drivers
  regulator: Support list_voltage for fixed voltage regulator
  regulator: Move regulator drivers to subsys_initcall()
  regulator: build fix for powerpc - renamed show_state
  regulator: add userspace-consumer driver
  Maxim 1586 regulator driver

ad6561df ("module: trim exception table on init
free.") put a bogus trim_init_extable() function into ia64 which didn't compile.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (22 commits)
  nilfs2: support contiguous lookup of blocks
  nilfs2: add sync_page method to page caches of meta data
  nilfs2: use device's backing_dev_info for btree node caches
  nilfs2: return EBUSY against delete request on snapshot
  nilfs2: modify list of unsupported features in caveats
  nilfs2: enable sync_page method
  nilfs2: set bio unplug flag for the last bio in segment
  nilfs2: allow future expansion of metadata read out via get info ioctl
  NILFS2: Pagecache usage optimization on NILFS2
  nilfs2: remove nilfs_btree_operations from btree mapping
  nilfs2: remove nilfs_direct_operations from direct mapping
  nilfs2: remove bmap pointer operations
  nilfs2: remove useless b_low and b_high fields from nilfs_bmap struct
  nilfs2: remove pointless NULL check of bpop_commit_alloc_ptr function
  nilfs2: move get block functions in bmap.c into btree codes
  nilfs2: remove nilfs_bmap_delete_block
  nilfs2: remove nilfs_bmap_put_block
  nilfs2: remove header file for segment list operations
  nilfs2: eliminate removal list of segments
  nilfs2: add sufile function that can modify multiple segment usages
  ...

On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.

For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be
auto loaded. Add the MODULE_ALIAS in case they do get built as modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>