- 11 Oct, 2005 3 commits
-
-
David S. Miller authored
Breakage noted by Al Viro. It breaks non-PCI builds, it's probably better to have a more direct implementation on sparc32, and which driver actually needs this is still questionable. We can resolve this in 2.6.15 Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Incorrect uart_write_wakeup() calls cause reference to a NULL tty pointer in sunsab and sunzilog serial drivers. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Linus Torvalds authored
-
- 10 Oct, 2005 36 commits
-
-
Andi Kleen authored
Need to use long long, not long when RMWing a MSR. I think it's harmless right now, but still should be better fixed if AMD adds any bits in the upper 32bit of HWCR. Bug was introduced with the TLB flush filter fix for i386 Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Andi Kleen authored
CPU hotplug fills up the possible map to NR_CPUs, but it did that after setting up per CPU data. This lead to CPU data not getting allocated for all possible CPUs, which lead to various side effects. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
-
Linus Torvalds authored
All the same issues - we can't just save the pointer to the thread, we must save the pid/uid/euid combination. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Harald Welte authored
If a process issues an URB from userspace and (starts to) terminate before the URB comes back, we run into the issue described above. This is because the urb saves a pointer to "current" when it is posted to the device, but there's no guarantee that this pointer is still valid afterwards. In fact, there are three separate issues: 1) the pointer to "current" can become invalid, since the task could be completely gone when the URB completion comes back from the device. 2) Even if the saved task pointer is still pointing to a valid task_struct, task_struct->sighand could have gone meanwhile. 3) Even if the process is perfectly fine, permissions may have changed, and we can no longer send it a signal. So what we do instead, is to save the PID and uid's of the process, and introduce a new kill_proc_info_as_uid() function. Signed-off-by: Harald Welte <laforge@gnumonks.org> [ Fixed up types and added symbol exports ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
David S. Miller authored
On the boot processor, we need to do the move onto the Linux trap table a little bit differently else we'll take unhandlable faults in the firmware address space. Previously we would do the following: 1) Disable PSTATE_IE in %pstate. 2) Set %tba by hand to sparc64_ttable_tl0 3) Initialize alternate, mmu, and interrupt global trap registers. 4) Call prom_set_traptable() That doesn't work very well actually with the way we boot the kernel VM these days. It worked by luck on many systems because the firmware accesses for the prom_set_traptable() call happened to be loaded into the TLB already, something we cannot assume. So the new scheme is this: 1) Clear PSTATE_IE in %pstate and set %pil to 15 2) Call prom_set_traptable() 3) Initialize alternate, mmu, and interrupt global trap registers. and this works quite well. This sequence has been moved into a callable function in assembler named setup-trap_table(). The idea is that eventually trampoline.S can use this code as well. That isn't possible currently due to some complications, but eventually we should be able to do it. Thanks to Meelis Roos for the Ultra5 boot failure report. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andi Kleen authored
Noticed by Terence Ripperda Undo wrong change in global_flush_tlb. We need to flush the caches in all cases, not just when pages were reverted. This was a bogus optimization added earlier, but it was wrong. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
-
Linus Torvalds authored
-
Vincent Sanders authored
Patch from Vincent Sanders Add a defconfig for the ARM Collie platform Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Vincent Sanders authored
Patch from Vincent Sanders Add a defconfig for the ARM Corgi Zarus platform Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Vincent Sanders authored
Patch from Vincent Sanders Add a defconfig for the ARM Poodle Zarus platform Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Vincent Sanders authored
Patch from Vincent Sanders Add a defconfig for the ARM Spitz Zarus platform Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Nicolas Pitre authored
Patch from Nicolas Pitre drivers/mfd/ucb1x00-core.c: In function 'ucb1x00_probe': drivers/mfd/ucb1x00-core.c:482: error: 'ucb1x00_class' undeclared (first use in this function) Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Markus F.X.J. Oberhumer authored
This fixes the setup of the alignment of the signal frame, so that all signal handlers are run with a properly aligned stack frame. The current code "over-aligns" the stack pointer so that the stack frame is effectively always mis-aligned by 4 bytes. But what we really want is that on function entry ((sp + 4) & 15) == 0, which matches what would happen if the stack were aligned before a "call" instruction. Signed-off-by: Markus F.X.J. Oberhumer <markus@oberhumer.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Benjamin Herrenschmidt authored
The logic in ide_do_request() doesn't guarantee that both drives will be serviced after a call. It may "forget" to service one in some circumstances, including when one of the drive is suspended (it will eventually fail to service the slave when the master is suspended for example). This prevents the wakeup requests that gets queued on wakeup from sleep from beeing serviced in some cases when 2 drives are sharing an IDE bus. The problem is deep enough in the way this code works (and there are probably a few other problematic but rare corner cases) and fixing it would require some major rethinking of the way IDE decides which channel to service. This is not 2.6.14 material. However, in the meantime, Bart has accepted this simple workaround that will fix the crash on wakeup from sleep since this specific corner case is actually hitting users to get into 2.6.14. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Tom Zanussi authored
The third param in this call to vmap shouldn't be GFP_KERNEL, which makes no sense, but rather VM_MAP. Thanks to Al Viro for spotting this. Signed-off-by: Tom Zanussi <zanussi@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
-
Jeff Dike authored
UML/x86_64 doesn't run when built with frame pointers disabled. There was an implicit frame pointer assumption in the stub segfault handler. With frame pointers disabled, UML dies on handling its first page fault. The container-of part of this is from Paolo Giarrusso <blaisorblade@yahoo.it>. Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Rafael J. Wysocki authored
The following patch makes swsusp avoid the possible temporary corruption of page translation tables during resume on x86-64. This is achieved by creating a copy of the relevant page tables that will not be modified by swsusp and can be safely used by it on resume. The problem is that during resume on x86-64 swsusp may temporarily corrupt the page tables used for the direct mapping of RAM. If that happens, a page fault occurs and cannot be handled properly, which leads to the solid hang of the affected system. This leads to the loss of the system's state from before suspend and may result in the loss of data or the corruption of filesystems, so it is a serious issue. Also, it appears to happen quite often (for me, as often as 50% of the time). The problem is related to the fact that (at least) one of the PMD entries used in the direct memory mapping (starting at PAGE_OFFSET) points to a page table the physical address of which is much greater than the physical address of the PMD entry itself. Moreover, unfortunately, the physical address of the page table before suspend (i.e. the one stored in the suspend image) happens to be different to the physical address of the corresponding page table used during resume (i.e. the one that is valid right before swsusp_arch_resume() in arch/x86_64/kernel/suspend_asm.S is executed). Thus while the image is restored, the "offending" PMD entry gets overwritten, so it does not point to the right physical address any more (i.e. there's no page table at the address pointed to by it, because it points to the address the page table has been at during suspend). Consequently, if the PMD entry is used later on, and it _is_ used in the process of copying the image pages, a page fault occurs, but it cannot be handled in the normal way and the system hangs. In principle we can call create_resume_mapping() from swsusp_arch_resume() (ie. from suspend_asm.S), but then the memory allocations in create_resume_mapping(), resume_pud_mapping(), and resume_pmd_mapping() must be made carefully so that we use _only_ NosaveFree pages in them (the other pages are overwritten by the loop in swsusp_arch_resume()). Additionally, we are in atomic context at that time, so we cannot use GFP_KERNEL. Moreover, if one of the allocations fails, we should free all of the allocated pages, so we need to trace them somehow. All of this is done in the appended patch, except that the functions populating the page tables are located in arch/x86_64/kernel/suspend.c rather than in init.c. It may be done in a more elegan way in the future, with the help of some swsusp patches that are in the works now. [AK: move some externs into headers, renamed a function] Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
Fix whitespace - I split this off the previous patch for easier review. Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
After restoring the existing code, make it work also when included in kernelspace code (which isn't currently the case, but at least this will prevent people from "fixing" it as just happened). Whitespace is fixed in next patch - it cluttered the diff too much. Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
Commit 44456d37, between 2.6.13-rc3 and -rc4, was a "nice cleanup" which broke something. Revert the offending part. It broke because: a) because this part doesn't fall under the description b) the author didn't know what he was doing here c) the author didn't try to compile the existing code and see that it worked perfectly. d) the author didn't ask us what was happening e) you didn't either, and somebody there should have learned that UML is a bit different. In fact, UML is special in linking to host libc and using its includes. In particular, since host includes always define both __BIG_ENDIAN and __LITTLE_ENDIAN, ntohll() macros started thinking to be in a big-endian world; and on-disk compatibility was broken. Many thanks go to Nix for reporting the problem and correctly diagnosing an endianness problem. Btw, this patch restores the previous code, which worked; but the definitions would be uncorrect if used in kernelspace files. Next patch addresses that. Cc: Nix <nix@esperi.org.uk>, Olaf Hering <olh@suse.de> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
For files which need to include glibc headers (i.e. userspace files), we specified the correct flags only for .o, not for .s/.lst/.i. Fix this. Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
Too many people were confused by skas0 and tried using "mode=skas0". And after all, they are right - accept this. Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Paolo 'Blaisorblade' Giarrusso authored
Add a missing $(Q) to a "ln" invocation. Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Steven Rostedt authored
The pccardd thread has a race in it that it can shutdown in the TASK_INTERRUPTIBLE state. Make sure we mark ourselves runnable again as we remove ourselves from the wait queue. Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-
Ben Dooks authored
Patch from Ben Dooks Initialise the driver's .owner field so that the device driver can be referenced to the module that owns it Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Ben Dooks authored
Patch from Ben Dooks Add initialisation of .owner field so that the device driver can be referenced to the module that owns it. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Richard Purdie authored
Patch from Richard Purdie Allow the GPIO pin suspend states to be specified for SCOOP devices. This is needed for correct operation on the spitz platform. Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Richard Purdie authored
Patch from Richard Purdie Add a missing include from corgi.c Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Richard Purdie authored
Patch from Richard Purdie Add some missing parameters from the scoop calls on collie. Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
George G. Davis authored
Patch from George G. Davis Add test for invalid LDRD/STRD Rd cases in ARM alignment handler and restore SWP printk KERN_ERR. Signed-off-by: Steve Longerbeam <slongerbeam@mvista.com> Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Sascha Hauer authored
Patch from Sascha Hauer Fix PD7_AF_UART2_DTR definition Signed-off-by: Giancarlo Formicuccia <gformicuccia@atinno.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Sascha Hauer authored
Patch from Sascha Hauer Fix error path in imx_startup. Signed-off-by: Giancarlo Formicuccia <gformicuccia@atinno.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Russell King authored
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
- 09 Oct, 2005 1 commit
-
-
Sven Hartge authored
irq.c is missing the inclusion of asm/io.h, which causes readb() and writeb() the be undefined. Signed-off-by: Sven Hartge <hartge@ds9.argh.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-