- 23 Sep, 2009 40 commits
-
-
Anton Vorontsov authored
Current bindings specify that "fsl,mpc8323-qe-usb" compatible entry should be used as a base match for QE UDCs, so update the driver to comply with the bindings. Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Frank Schaefer authored
This is how "real" UARTs (e.g. 16550) work and AFAIK what RS232 specifies, too. Make the driver more compliant. Signed-off-by:
Frank Schaefer <schaefer.frank@gmx.net> Signed-off-by:
-
Frank Schaefer authored
The device supports it, so why not use it ? Works fine ! Signed-off-by:
-
Frank Schaefer authored
According to the datasheets, the PL2303 supports a set of 25 baudrates. The baudrate is set as a 4 byte value directly. During my experiments with device 067b:2303 (PL2303X), I noticed that - the bridge-controller always uses 9600 baud if invalid/unsupported baud rate values are set - the baud rate value returned by usb_control_msg(..., GET_LINE_REQUEST, ...) does not reflect the actually used baudrate. Always the last set value is returned, even if it was invalid and not used by the controller. This patch fixes the following issues with the current code: 1.) make sure that only supported baudrates are set (are there any buggy chip revisions out there which don't "like" other values... ?). 2.) always set the baudrate to the next nearest supported baudrate. 3.) applications can now read back the resulting baudrate properly, because tty_encode_baud_rate(...) is now fed with the actually used baudrate. Signed-off-by: -
Olivier Bornet authored
Using the module parameter vcc_default, you can choose the default VCC value. Signed-off-by:
Olivier Bornet <Olivier.Bornet@puck.ch> Signed-off-by:
-
Olivier Bornet authored
Signed-off-by:
-
Olivier Bornet authored
You can now set the IUU reader to 3.3V VCC instead of 5V VCC, using the sysfs parameter vcc_mode. Valid values are 3 and 5. Signed-off-by:
-
Olivier Bornet authored
Signed-off-by:
-
Olivier Bornet authored
Resetting the device cause the device to have a new name in the /dev. Signed-off-by:
-
Steve Holland authored
Follow T&M convention of obeying EOM flag. Avoid exception cases where instrument response size matches a buffer size. Signed-off-by:
Steve Holland <sdh4@iastate.edu> Signed-off-by:
-
Steve Holland authored
Limit data copied to userspace to amount requested. Prevents a faulty instrument from overwriting user memory. Signed-off-by:
-
Steve Holland authored
The header size should not be included in the number of bytes requested of the instrument Signed-off-by:
-
Tim Small authored
Here is a patch to the ch341 driver which adds serial break support. Signed-off-by:
Tim Small <tim@seoss.co.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
-
Alan Stern authored
This patch (as1275) fixes the s3c2410 device controller driver. Its usb_gadget_unregister_driver() routine is supposed to call the gadget driver's unbind method, not the disconnect method. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Brian Niebuhr authored
This patch adds a CDC EEM ethernet gadget driver. CDC EEM is a newer USB ethernet specification that uses a simpler interface than the older CDC ECM. This makes CDC EEM usable by a wider set of USB hardware. By default the ethernet gadget will still use CDC ECM/Subset, but kernel configuration and/or a module parameter will allow alternative use of the CDC EEM protocol. Changes since last version: - Brought in missing RNDIS changes that caused compile error - Modified 'sentinel CRC' checking to match EEM host driver Signed-off-by:
Brian Niebuhr <bniebuhr@efjohnson.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Oliver Neukum authored
These printks can be removed as they only provide information about the driver not the device and nobody has ever provided feedback. Signed-off-by:Oliver Neukum <oliver@neukum.org>
-
David VomLehn authored
When do_output_char() attempts to write a carriage return/line feed sequence, it first checks to see how much buffer room is available. If there are at least two characters free, it will write the carriage return/line feed with two calls to tty_put_char(). It calls the tty_operation functions write() for devices that don't support the tty_operations function put_char(). If the USB generic serial device's write URB is not in use, it will return the buffer size when asked how much room is available. The write() of the carriage return will cause it to mark the write URB busy, so the subsequent write() of the line feed will be ignored. This patch uses the kfifo infrastructure to implement a write FIFO that accurately returns the amount of space available in the buffer. Signed-off-by:
David VomLehn <dvomlehn@cisco.com> Signed-off-by:
-
H Hartley Sweeten authored
Remove unused variable in ohci-ep93xx.c. This only shows up when CONFIG_PM is enabled. Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Lennert Buytenhek <kernel@wantstofly.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Randy Dunlap authored
subsys_initcall_sync() is only defined for built-in code, not for loadable modules, so this driver build fails when built as a module. However, the _sync() forms of the initcalls are not implemented, so this should not be used -- just use the non-sync form of it. drivers/usb/otg/twl4030-usb.c:777: warning: data definition has no type or storage class drivers/usb/otg/twl4030-usb.c:777: warning: type defaults to 'int' in declaration of 'subsys_initcall_sync' drivers/usb/otg/twl4030-usb.c:777: warning: parameter names (without types) in function declaration Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Brian Niebuhr authored
This is an alternate solution to the EEM 'sentinel' CRC valiation issue. CDC EEM allows using a 'sentinel' ethernet frame CRC of 0xdeadbeef in place of a real CRC. The 'sentinel' value is transmitted in big-endian order whereas the normal CRC is little-endian. This patch handles both cases appropriately. Signed-off-by:
-
Li Yang authored
Change the F entry for file rename, and make it also cover fsl_qe_udc driver. Update the name accordingly. Signed-off-by:
Li Yang <leoli@freescale.com> Acked-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Joe Perches <joe@perches.com> Signed-off-by:
-
Julia Lawall authored
Correct priority problem in the use of ! and &. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ expression E; constant C; @@ - !E & C + !(E & C) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Jon Hunter authored
This patch was previously discussed in the following thread: http://thread.gmane.org/gmane.linux.usb.general/19472/focus=19484 On the OMAP3 device the usbhost controller is in a separate internal power-domain. So when the usbhost is inactive or suspend is called, we can disable clocks and power-down the usbhost to save power. Recently we found that after calling ehci_bus_suspend() and disabling the usbhost clocks we would see the ehci watchdog timer event fire. This was causing a kernel panic because the usbhost controllers clocks were disabled and inside the watchdog timer function the clocks were not being re-enabled, so when the ehci registers were accessed this resulted in a CPU data-abort. To avoid this panic, per recommendation from Alan Stern (see above thread), we make sure any pending timer events (that may have been scheduled by calling ehci_work within the ehci_bus_suspend() function) are deleted before returning. Signed-off-by:
Fei Yang <fei.yang@motorola.com> Signed-off-by:
Jon Hunter <jon-hunter@ti.com> Acked-by:
-
Ming Lei authored
This patch fixes the .probe failure of twl4030_usb driver if it is compiled into kernel. Since twl4030_usb USB transceiver .probe depends on twl4030-regulator, marking twl4030_usb_init as subsys_initcall_sync can make it called after twl4030-regulator initialization is finished, then twl4030_usb USB transceiver driver can be probed successfully. Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Ajay Kumar Gupta authored
Invoke put_device(musb->xceiv->dev) before musb_platform_exit()as xceiv is getting unregistered in musb_platform_exit(). Fixes put_device() panic when module insert/removal is performed multiple times. Signed-off-by:
Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
David Woodhouse authored
We are seeing a number of crashes in SMM, when VT-d is enabled while 'Legacy USB support' is enabled in various BIOSes. The BIOS is supposed to indicate which addresses it uses for DMA in a special ACPI table ("RMRR"), so that we can punch a hole for it when we set up the IOMMU. The problem is, as usual, that BIOS engineers are totally incompetent. They write code which will crash if the DMA goes AWOL, and then they either neglect to provide an RMRR table at all, or they put the wrong addresses in it. And of course they don't do _any_ QA, since that would take too much time away from their crack-smoking habit. The real fix, of course, is for consumers to refuse to buy motherboards which only have closed-source firmware available. If we had _open_ firmware, bugs like this would be easy to fix. Since that's something I can only dream about, this patch implements an alternative -- ensuring that the USB controllers are handed off from the BIOS and quiesced _before_ the IOMMU is initialised. That would have been a much better design than this RMRR nonsense in the first place, of course. The bootloader has no business doing DMA after the OS has booted anyway. Signed-off-by:David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Markus Rechberger authored
The current limit only allows isochronous transfers up to 32kbyte/urb, updating this to 192 kbyte/urb improves the reliability of the transfer. USB 2.0 transfer is possible with 32kbyte but increases the chance of corrupted/incomplete data when the system is performing some other tasks in the background. http://www.spinics.net/lists/linux-usb/msg19955.htmlSigned-off-by:
Markus Rechberger <mrechberger@gmail.com> Cc: Oliver Neukum <oliver@neukum.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Ken MacLeod authored
HCHWCFG_PULLDOWN_DS2 and HCHWCFG_PULLDOWN_DS1 were swapped. Incorrect operator precedence in isp1362_hc_start() hid part of the problem. This fixes a problem where Port 1 in Host mode fails to see disconnects. Signed-Off-By:
Ken MacLeod <ken@bitsko.slc.ut.us> Signed-off-by:
-
Robin Callender authored
The included patch can be applied to the new usb gadget audio driver. It addresses a seg-fault in uncovered in g_audio.ko. The fault occurs in the function u_audio.c::gaudio_open_end_dev() when device /dev/snd/pcmC0D0c (FILE_PCM_CAPTURE) is not present. I suspect there may be similar problems with device /dev/snd/pcmC0D0p (FILE_PCM_PLAYBACK) handling also. I leave that for the developer(s), as I was unsure as to the side-effects of not calling playback_default_hw_params() in the initialization phase. Signed-off-by:
Robin Callender <robin_callender@hotmail.com> Signed-off-by:
-
Roel Kluin authored
Check whether index is within bounds before testing the element. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
fangxiaozhi authored
In this patch, we always make the return value of function usb_stor_huawei_e220_init to be zero. Then it will not prevent usb-storage driver from attaching to the CDROM device of Huawei Datacard. Signed-off-by:
fangxiaozhi <huananhu@huawei.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Ondrej Zary authored
Add IrDA support to ark3116 driver. This makes Gembird UIR-22 USB to IrDA adapter work (vendor ID 0x18ec, device ID 0x3118). This adapter contains ARK3116T USB serial chip and an IrDA transceiver, thus a command like "irattach /dev/ttyUSB0 -s" is needed. All magic numbers were captured using usbsnoop from windows driver that came with the device. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Aric Blumer authored
Some ohci-pxa27x platforms may require OCPM and NOCP in UHCRHDA to be clear, but the existing code was only allowing setting. This patch ensures that these bits are clear if the respective flags are not set. This is particularly important for the PXA3xx family where the documentation says OCPM must be cleared, but it is set after reset. Signed-off-by:
Aric Blumer <aric@sdgsystems.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Anand Gadiyar authored
EHCI: OHCI: Remove unnecessary includes of reboot.h Signed-off-by:
Anand Gadiyar <gadiyar@ti.com> Acked-by:
-
Michael S. Tsirkin authored
include/linux/usb/audio.h is exported to userspace, so part of this file that is for internal kernel usage need to be guarded with ifdef __KERNEL__. This way make headers_install will stript it out. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Nicolas Ferre authored
At91sam9g45 series has a set of high speed USB interfaces. The host driver is an EHCI with its companion OHCI. OHCI is always handled by ohci-at91.c. This wrapper is just modified to allow IRQ sharing between two controllers. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by:
-
Nicolas Ferre authored
Add gadget USB drivers for at91sam9g45 series. Those SOC include high speed USB interfaces. The gadget driver is the already available atmel_usba_udc. Signed-off-by:
-
Nicolas Ferre authored
Add host USB High speed driver for at91sam9g45 series. The host driver is an EHCI with its companion OHCI. EHCI is handled by the new ehci-atmel.c whereas the OHCI is always handled by ohci-at91.c. Signed-off-by:
-
Bob Liu authored
Signed-off-by:
Bob Liu <yjfpb04@gmail.com> Acked-by:
-
Randy Dunlap authored
Fix printk format warnings: drivers/usb/class/usbtmc.c:466: warning: format '%zu' expects type 'size_t', but argument 4 has type 'u32' drivers/usb/class/usbtmc.c:466: warning: format '%zu' expects type 'size_t', but argument 5 has type 'int' Signed-off-by:
-
