Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

For some reason, sata_via is missing PM hooks.  Add them.  Spotted by
Jeroen Janssen <jeroen.janssen@gmail.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeroen Janssen <jeroen.janssen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.

As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

update pata_pcmcia to add card ident for JVC MP-CDX1 cdrom drive
card info:
PRODID_1="KME"
PRODID_2="KXLC005"
PRODID_3="00"
MANFID=0032,2904
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

There is a known problem with sata_promise on SATAII-150/300 TX4
controller cards: it enumerates drives in an order that differs
from the port numbers printed on the controller cards. However,
Promise's BIOS and Linux driver both get the order right.

I investigated Promise's Linux driver (v1.01.0.23), and found
that it explicitly changes the mapping from logical port number
to ATA engine MMIO address on the SATAII TX4 cards. It does this
on all SATAII TX4 cards, without inspecting revision etc. The
SATAII TX2plus cards continue to use the same mapping that was
used for the first-generation chips.

This patch updates sata_promise to use the new port number to
ATA engine mapping on SATAII TX4 cards, which fixes the drive
enumeration order problem on those cards. Tested on several
1st and 2nd generation TX2plus and TX4 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The sata_promise error decode update changed pdc_host_intr()
to return and not complete the qc after detecting an error.
Unfortunately not completing the qc:s causes them to always
time out on error, which is wrong and has nasty side-effects.

This patch updates pdc_error_intr() to call ata_port_abort(),
similar to ahci and sata_sil24. Doing this is important as it
makes EH see the original error and not a bogus timeout.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

_GTF command is never ATA_PROT_ATAPI_NODATA whether the device is
ATAPI or not.  It's always ATA_PROT_NODATA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix PIO setup on resume for ATAPI devices
  ide: legacy PCI bus order probing fixes
  ide: add ide_proc_register_port()
  ide: add "initializing" argument to ide_register_hw()
  ide: cable detection fixes (take 2)
  ide: move IDE settings handling to ide-proc.c
  ide: split off ioctl handling from IDE settings (v2)
  ide: make /proc/ide/ optional
  ide: add ide_tune_dma() helper
  ide: rework the code for selecting the best DMA transfer mode (v3)
  ide: fix UDMA/MWDMA/SWDMA masks (v3)

* git://git.linux-nfs.org/pub/linux/nfs-2.6:
  NFS: Kill the obsolete NFS_PARANOIA
  NFS: use __set_current_state()
  sunrpc: fix crash in rpc_malloc()
  NFS: Clean up NFSv4 XDR error message
  NFS: NFS client underestimates how large an NFSv4 SETATTR reply can be
  SUNRPC: Fix pointer arithmetic bug recently introduced in rpc_malloc/free
  NFS: Remove redundant check in nfs_check_verifier()
  NFS: Fix a jiffie wraparound issue

PIO should be restored also for ATAPI devices during resume, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE PCI host drivers should register themselves with IDE core only when
IDE driver is built-in, otherwise (IDE driver is modular and thus IDE PCI
host drivers are also modular) the code has no effect and just complicates
the probing.

Fix it by adding new config option CONFIG_IDEPCI_PCIBUS (defined only when
needed and invisible to the user) and covering by #ifdef/#endif the code
in question.  It turned out that "ide=reverse" was silently accepted but did
nothing in case when IDE driver was modular, this is fixed now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* create_proc_ide_interfaces() tries to add /proc entries for every probed
  and initialized IDE port, replace it by ide_proc_register_port() which does
  it only for the given port (also rename destroy_proc_ide_interface() to
  ide_proc_unregister_port() for consistency)
  
* convert {create,destroy}_proc_ide_interface[s]() users to use new functions

* pmac driver depended on proc_ide_create() to add /proc port entries, fix it
  
* au1xxx-ide, swarm and cs5520 drivers depended indirectly on ide-generic
  driver (CONFIG_IDE_GENERIC=y) to add port /proc entries, fix them

* there is now no need to add /proc entries for IDE ports in proc_ide_create()
  so don't do it

* proc_ide_create() needs now to be called before drivers are probed - fix it,
  while at it make proc_ide_create() create /proc "ide" directory
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add "initializing" argument to ide_register_hw() and use it instead of ide.c
wide variable of the same name.  Update all users of ide_register_hw()
accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...

* print user-friendly warning about limiting the maximum transfer speed
  to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
  also while at it cleanup eighty_ninty_three() a bit

* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
  - bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
    were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
    (please see FIXME comment in eighty_ninty_three() for more details)
  - CONFIG_IDEDMA_IVB=y/n cases were interchanged
  - check for SATA devices was missing

* remove private cable warnings from pdc_202xx{old,new} drivers now that core
  code provides this functionality (plus, in pdc202xx_new case the test could
  give false warnings for ATAPI devices because pdc202xx_new driver doesn't
  even support ATAPI DMA)

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* move
	__ide_add_setting()
	ide_add_setting()
	__ide_remove_setting()
	auto_remove_settings()
	ide_find_setting_by_name()
	ide_read_setting()
	ide_write_setting()
	set_xfer_rate()
	ide_add_generic_settings()
	ide_register_subdriver()
	ide_unregister_subdriver()

  from ide.c to ide-proc.c

* set_{io_32bit,pio_mode,using_dma}() cannot be marked static now, fix it

* rename ide_[un]register_subdriver() to ide_proc_[un]register_driver(),
  update device drivers to use new names

* add CONFIG_IDE_PROC_FS=n versions of ide_proc_[un]register_driver()
  and ide_add_generic_settings()

* make ide_find_setting_by_name(), ide_{read,write}_setting()
  and ide_{add,remove}_proc_entries() static

* cover IDE settings code in device drivers with CONFIG_IDE_PROC_FS #ifdef,
  also while at it cover with CONFIG_IDE_PROC_FS #ifdef ide_driver_t.proc

* remove bogus comment from ide.h

* cover with CONFIG_IDE_PROC_FS #ifdef .proc and .settings in ide_drive_t

Besides saner code this patch results in the IDE core smaller by ~2 kB
(on x86-32) and IDE disk driver by ~1 kB (ditto) when CONFIG_IDE_PROC_FS=n.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* do write permission and min/max checks in ide_procset_t functions

* ide-disk.c: drive->id is always available so cleanup "multcount" setting
  accordingly

* ide-disk.c: "address" setting was incorrectly defined as type TYPE_INTA,
  fix it by using type TYPE_BYTE and updating ide_drive_t->adressing field,
  the bug didn't trigger because this IDE setting uses custom ->set function

* ide.c: add set_ksettings() for handling HDIO_SET_KEEPSETTINGS ioctl

* ide.c: add set_unmaskirq() for handling HDIO_SET_UNMASKINTR ioctl

* handle ioctls directly in generic_ide_ioclt() and idedisk_ioctl()
  instead of using IDE settings to deal with them

* remove no longer needed ide_find_setting_by_ioctl() and {read,write}_ioctl
  fields from ide_settings_t, also remove now unused TYPE_INTA handling

v2:
* add missing EXPORT_SYMBOL_GPL(ide_setting_sem) needed now for ide-disk
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All important information/features should be already available through
sysfs and ioctl interfaces.

Add CONFIG_IDE_PROC_FS (CONFIG_SCSI_PROC_FS rip-off) config option,
disabling it makes IDE driver ~5 kB smaller (on x86-32).

While at it add CONFIG_PROC_FS=n versions of proc_ide_{create,destroy}()
and remove no longer needed #ifdefs.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After reworking the code responsible for selecting the best DMA
transfer mode it is now possible to add generic ide_tune_dma() helper.

Convert some IDE PCI host drivers to use it (the ones left need more work).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* use 0x00 instead of 0x80 to disable ->{ultra,mwdma,swdma}_mask
* add udma_mask field to ide_pci_device_t and use it to initialize
  ->ultra_mask in aec62xx, cmd64x, pdc202xx_{new,old} and piix drivers
* fix UDMA masks to match with chipset specific *_ratemask()
  (alim15x3, hpt366, serverworks and siimage drivers need UDMA mask
   filtering method - done in the next patch)

v2:
* piix: fix cable detection for 82801AA_1 and 82372FB_1
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* cmd64x: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
* aec62xx: fix newly introduced bug - check DMA status not command register
  [ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* piix: use hwif->cds->udma_mask
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

use __set_current_state(TASK_*) instead of current->state = TASK_*, in fs/nfs
Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

While the comment says:
 * To prevent rpciod from hanging, this allocator never sleeps,
 * returning NULL if the request cannot be serviced immediately.

The function does not actually check for NULL pointers being returned.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Make it more useful for debugging purposes.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

The maximum size of an NFSv4 SETATTR compound reply should include the
GETATTR operation that we send.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Use a cleaner method to find the size of an rpc_buffer.  This actually
works on x86-64!
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

The check for nfs_attribute_timeout(dir) in nfs_check_verifier is
redundant: nfs_lookup_revalidate() will already call nfs_revalidate_inode()
on the parent dir when necessary.

The only case where this is not done is the case of a negative dentry. Fix
this case by moving up the revalidation code.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

dentry verifiers are always set to the parent directory's
cache_change_attribute. There is no reason to be testing for anything other
than equality when we're trying to find out if the dentry has been checked
since the last time the directory was modified.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Seems more than just deprecated, we can't build using SA_INTERUPT.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] wire up pselect, ppoll
  [IA64] Add TIF_RESTORE_SIGMASK
  [IA64] unwind did not work for processes born with CLONE_STOPPED
  [IA64] Optional method to purge the TLB on SN systems
  [IA64] SPIN_LOCK_UNLOCKED macro cleanup in arch/ia64
  [IA64-SN2][KJ] mmtimer.c-kzalloc
  [IA64] fix stack alignment for ia32 signal handlers
  [IA64] - Altix: hotplug after intr redirect can crash system
  [IA64] save and restore cpus_allowed in cpu_idle_wait
  [IA64] Removal of percpu TR cleanup in kexec code
  [IA64] Fix some section mismatch errors

* git://git.infradead.org/mtd-2.6: (21 commits)
  [MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
  [MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
  [MTD] Remove unnecessary user space check from mtd.h.
  [MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
  [MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
  [MTD] [NAND] platform NAND driver: add driver
  [MTD] [NAND] platform NAND driver: update header
  [JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
  [JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
  [JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
  [JFFS2] Remember to calculate overlap on nodes which replace older nodes
  [JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
  [MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
  [MTD] [NAND] Tidy up handling of page number in nand_block_bad()
  [MTD] block2mtd_paramline[] mustn't be __initdata
  [MTD] [NAND] Support multiple chips in CAFÉ driver
  [MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
  [MTD] [NAND] Use rslib for CAFÉ ECC
  [RSLIB] Support non-canonical GF representations
  [JFFS2] Remove dead file histo_mips.h
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Fix stacktrace simplification fallout.
  sh: SH7760 DMABRG support.
  sh: clockevent/clocksource/hrtimers/nohz TMU support.
  sh: Truncate MAX_ACTIVE_REGIONS for the common case.
  rtc: rtc-sh: Fix rtc_dev pointer for rtc_update_irq().
  sh: Convert to common die chain.
  sh: Wire up utimensat syscall.
  sh: landisk mv_nr_irqs definition.
  sh: Fixup ndelay() xloops calculation for alternate HZ.
  sh: Add 32-bit opcode feature CPU flag.
  sh: Fix PC adjustments for varying opcode length.
  sh: Support for SH-2A 32-bit opcodes.
  sh: Kill off redundant __div64_32 symbol export.
  sh: Share exception vector table for SH-3/4.
  sh: Always define TRAPA_BUG_OPCODE.
  sh: __GFP_REPEAT for pte allocations, too.
  rtc: rtc-sh: Fix up dev_dbg() warnings.
  sh: generic quicklist support.

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
  ARM: OMAP: Fix GCC-reported compile time bug
  ARM: OMAP: restore CONFIG_GENERIC_TIME
  ARM: OMAP: partial LED fixes
  ARM: OMAP: add SoSSI clock (call propagate_rate for childrens)
  ARM: OMAP: FB sync with N800 tree (support for dynamic SRAM allocations)
  ARM: OMAP: Sync framebuffer headers with N800 tree
  ARM: OMAP: Mostly cosmetic to sync up with linux-omap tree
  ARM: OMAP: Fix gpmc header
  ARM: OMAP: Add mailbox support for IVA
  [ARM] armv7: add Makefile and Kconfig entries
  [ARM] armv7: add support for asid-tagged VIVT I-cache
  [ARM] armv7: add dedicated ARMv7 barrier instructions
  [ARM] armv7: Add ARMv7 cacheid macros
  [ARM] armv7: add support for ARMv7 cores.
  [ARM] Fix ARM branch relocation range
  [ARM] 4363/1: AT91: Remove legacy PIO definitions
  [ARM] 4361/1: AT91: Build error
  ARM: OMAP: Sync core code with linux-omap
  ARM: OMAP: Sync headers with linux-omap
  ARM: OMAP: h4 must have blinky leds!!
  ...

Commit 6fe6900e introduced a nasty bug
in read_cache_page_async().

It added a "mark_page_accessed(page)" at the final return path in
read_cache_page_async().  But in error cases, 'page' holds the error
code, and you can't mark it accessed.

[ and Glauber de Oliveira Costa points out that we can use a return
  instead of adding more goto's ]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Further fixes for the removal of 4level-fixup hack from ppc32
  [POWERPC] EEH: log all PCI-X and PCI-E AER registers
  [POWERPC] EEH: capture and log pci state on error
  [POWERPC] EEH: Split up long error msg
  [POWERPC] EEH: log error only after driver notification.
  [POWERPC] fsl_soc: Make mac_addr const in fs_enet_of_init().
  [POWERPC] Don't use SLAB/SLUB for PTE pages
  [POWERPC] Spufs support for 64K LS mappings on 4K kernels
  [POWERPC] Add ability to 4K kernel to hash in 64K pages
  [POWERPC] Introduce address space "slices"
  [POWERPC] Small fixes & cleanups in segment page size demotion
  [POWERPC] iSeries: Make HVC_ISERIES the default
  [POWERPC] iSeries: suppress build warning in lparmap.c
  [POWERPC] Mark pages that don't exist as nosave
  [POWERPC] swsusp: Introduce register_nosave_region_late

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
  sound: convert "sound" subdirectory to UTF-8
  MAINTAINERS: Add cxacru website/mailing list
  include files: convert "include" subdirectory to UTF-8
  general: convert "kernel" subdirectory to UTF-8
  documentation: convert the Documentation directory to UTF-8
  Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
  remove broken URLs from net drivers' output
  Magic number prefix consistency change to Documentation/magic-number.txt
  trivial: s/i_sem /i_mutex/
  fix file specification in comments
  drivers/base/platform.c: fix small typo in doc
  misc doc and kconfig typos
  Remove obsolete fat_cvf help text
  Fix occurrences of "the the "
  Fix minor typoes in kernel/module.c
  Kconfig: Remove reference to external mqueue library
  Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
  Correct comments in genrtc.c to refer to correct /proc file.
  Fix more "deprecated" spellos.
  Fix "deprecated" typoes.
  ...

Fix trivial comment conflict in kernel/relay.c.

* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
  [AVR32] Wire up sys_utimensat
  [AVR32] Fix section mismatch .taglist -> .init.text
  [AVR32] Implement dma_{alloc,free}_writecombine()
  AVR32: Spinlock initializer cleanup
  [AVR32] Use correct config symbol when setting cpuflags

When implementing things as macros, make sure we use typecasts and
parentheses where needed.  The macros as defined were vulnerable to
surreptitious promotion causing problems.

Avoid macros where practical; e.g. wrmsr() can be an inline instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

All users to the two-part rdtsc() macro have already switched to using
rdtscl() or rdtscll().  Remove the now-obsolete macro.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The definition of USER686 is supposed to be a mask of feature bits,
not an OR of feature numbers!  It happened to work anyway on the only
processor affected, simply by pure coincidence.  Fix.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>