Fixes (again) whole-system lockups due to GPU lockups.
Signed-off-by: Eric Anholt <eric@anholt.net>

According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.

G45 PRM, Vol 1b, p101:
  While the “free space” wrap may allow commands to be wrapped around the
  end of the Ring Buffer, the wrap should only occur between commands.
  Padding (with NOP) may be required to follow this restriction.

Do as commanded.

[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

mac Mini's have a single DDC line on the DVI connector, shared between the
analog link and the digital link. So, if DDC isn't detected on GPIOE (the
usual SDVO DDC link), try GPIOA (the usual VGA DDC link) when there isn't a
VGA monitor connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

It seems that on IGDNG the same swizzling setup always applys.
And front buffer tiling needs to set address swizzle in display
arb control too.

Fix plane tricle feed setting in v1 which should be disable bit,
and always setup address swizzle to let hardware care for buffer
tiling in all cases.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>

And clean up a small whitespace goof-up in the same function, while
I was looking at it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.

This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.

TODO: it appears the normal unplug interrupt is missed as reported by Li Peng,
need more checks here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Currently SDVO TV only support NTSC-M format. In this patch
we introduce PAL and SECAM formats available and create seting-format
property at init time. When user dynamically chose preferred
format by xrandr command, it will refine all modelines
provided by SDVO device, then instruct SDVO device to execute.
At the same time the property is added for SDVO-TV so that the SDVO-TV mode can be changed
by using xrandr.

https://bugs.freedesktop.org/show_bug.cgi?id=22891Signed-off-by: Ma Ling <ling.ma@intel.com>
review-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

For integrated TV there are 3 connector types: S-VIDEO, Composite and
Component(YprPb). Those tv formats whose component flag is true should
be assigned to Component connector, others are for S-VIDEO and Composite.
The patch intends to find appropriate tv format for each connector.
In such case it will return the correct modeline to user space. Otherwise
it will return the incorrect modeline when S-video/composite is connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Add a debugfs file to dump the entire register range. Here we
assume that reading write-only/reserved registers won't make the chip
angry. Seems to hold true, thankfully.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
[anholt: hand-applied for conflicts]
Signed-off-by: Eric Anholt <eric@anholt.net>

New variant of IGDNG mobile chip has new host bridge id.

[anholt: Note that this new PCI ID doesn't impact the DRM, which doesn't
care about the PCI ID of the bridge]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Remember to release the local reference if we fail to wait on
the rendering.

(Also whilst in the vicinity add some whitespace so that the phasing of
the operations is clearer.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>

Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.

Fixes fdo bug #23368.  Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>

In the recent change by Al Viro that changes verious subsystems
to use "struct path" one case was missed in the autofs4 module
which causes mounts to no longer expire.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix MacBookPro 3,1/4,1 quirk with ALC889A
  ALSA: hda - Add missing mux check for VT1708

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (12564a): MAINTAINERS: Update gspca sn9c20x name style
  V4L/DVB (12502): gspca - sn9c20x: Fix gscpa sn9c20x build errors.
  V4L/DVB (12495): em28xx: Don't call em28xx_ir_init when disable_ir is true
  V4L/DVB (12457): zr364: wrong indexes
  V4L/DVB (12451): Update KConfig File to enable SDIO and USB interfaces
  V4L/DVB (12450): Siano: Fixed SDIO compilation bugs
  V4L/DVB (12449): adds webcam for Micron device MT9M111 0x143A to em28xx
  V4L/DVB (12446): sms1xxx: restore GPIO functionality for all Hauppauge devices

My previous patch (commit 4f8ee2c9: "lmb: Remove __init from
lmb_end_of_DRAM()") removed __init in lmb.c but missed the fact that it
was also marked as such in the .h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit log for commit 517d3cc1
("[libata] ata_piix: Enable parallel scan") says:

    This patch turns on parallel scanning for the ata_piix driver.
    This driver is used on most netbooks (no AHCI for cheap storage it seems).
    The scan is the dominating time factor in the kernel boot for these
    devices; with this flag it gets cut in half for the device I used
    for testing (eeepc).
    Alan took a look at the driver source and concluded that it ought to be safe
    to do for this driver.  Alan has also checked with the hardware team.

and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.

I used the following test to check whether the issue is real:

  @@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
   			(timings[pio][1] << 8);
   	}
   	pci_write_config_word(dev, master_port, master_data);
  -	if (is_slave)
  +	if (is_slave) {
  +		if (ap->port_no == 0) {
  +			u8 tmp = slave_data;
  +
  +			while (slave_data == tmp) {
  +				pci_read_config_byte(dev, slave_port, &tmp);
  +				msleep(50);
  +			}
  +
  +			dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
  +				   "race detected\n");
  +		}
   		pci_write_config_byte(dev, slave_port, slave_data);
  +	}

   	/* Ensure the UDMA bit is off - it will be turned back on if
   	   UDMA is selected */

and it indeed triggered the error message.

Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.

[ Alan: would be better to take the host lock in libata-core for these
  cases so that we fix all the adapters in one swoop.  "Looks fine as a
  temproary quickfix tho" ]

Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Improve CRTDDC mapping by using VBT info
  drm/i915: Fix CPU-spinning hangs related to fence usage by using an LRU.
  drm/i915: Set crtc/clone mask in different output devices
  drm/i915: Always use SDVO_B detect bit for SDVO output detection.
  drm/i915: Fix typo that broke SVID1 in intel_sdvo_multifunc_encoder()
  drm/i915: Check if BIOS enabled dual-channel LVDS on 8xx, not only on 9xx
  drm/i915: Set the multiplier for SDVO on G33 platform

This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.

Reference: kernel bug#14078
	http://bugzilla.kernel.org/show_bug.cgi?id=14078Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element.  Simpliy
adding the call of get_mux_nids() fixes the problem.

Reference: Novell bnc#534904
	https://bugzilla.novell.com/show_bug.cgi?id=534904Signed-off-by: Takashi Iwai <tiwai@suse.de>

To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Reported-by: Toralf Forster <toralf.foerster@gmx.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

We should call em28xx_ir_init(dev) only when disable_ir is true.
Signed-off-by: Shine Liu <shinel@foxmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The order of indexes is reversed
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Update KConfig file to enbale selection of SDIO and USB
interfaces, and add dependancy on relevant modules.

[mchehab@redhat.com: fix merge conflicts, remove default: m, add missing endmenu]
Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fixed SDIO compilation bugs
Also fixed a memory overrun issue in buffer management.
Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Previous changesets broke Hauppauge devices and their GPIO configurations.

This changeset restores the LED & LNA functionality.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Use VBT information to determine which DDC bus to use for CRTDCC.
Fall back to GPIOA if VBT info is not available.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested on: 855 (David), and 945GM, 965GM, GM45, and G45 (anholt)

The lack of a proper LRU was partially worked around by taking the fence
from the object containing the oldest seqno.  But if there are multiple
objects inactive, then they don't have seqnos and the first fence reg
among them would be chosen.  If you were trying to copy data between two
mappings, this could result in each page fault stealing the fence from
the other argument, and your application hanging.

https://bugs.freedesktop.org/show_bug.cgi?id=23566
https://bugs.freedesktop.org/show_bug.cgi?id=23220
https://bugs.freedesktop.org/show_bug.cgi?id=23253
https://bugs.freedesktop.org/show_bug.cgi?id=23366

Cc: Stable Team <stable@kernel.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: don't free non-existent backlight in acpi video module
  toshiba_acpi: return on a fail path
  ACPICA: Windows compatibility fix: same buffer/string store

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  inotify: update the group mask on mark addition
  inotify: fix length reporting and size checking
  inotify: do not send a block of zeros when no pathname is available

On Tue, Aug 18, 2009 at 01:45:17PM -0400, John David Anglin wrote:
>  CC      arch/parisc/kernel/traps.o
> arch/parisc/kernel/traps.c: In function 'handle_interruption':
> arch/parisc/kernel/traps.c:535:18: warning: operation on 'regs->iasq[0]'
> may be undefined

Yes - Line 535 should use both [0] and [1].
Reported-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>