- 16 Jul, 2008 40 commits
-
-
Anton Vorontsov authored
This patch fixes RTC on MPC8572DS boards: dummy read helps only when reading at the end of the bridge's memory (i.e. outside of behind the bridge devices' assigned regions). With this change the quirk also makes RTC work on MPC8610HPCD, so it's unlikely that this will break MPC8641HPCN or MPC8544DS boards. Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
Kumar Gala <galak@kernel.crashing.org>
-
Jochen Friedrich authored
Signed-off-by:
Jochen Friedrich <jochen@scram.de> Signed-off-by:
-
Anton Vorontsov authored
This patch adds few bindings for the new drivers to be submitted through the appropriate maintainers. Signed-off-by:
-
Anton Vorontsov authored
Freescale ships MPC8315E-RDB boards in two variants: 1. With TSEC1 ethernet support and USB UTMI PHY; 2. Without TSEC1 support, but with USB ULPI PHY in addition. For the second case U-Boot will add status = "disabled"; property into the TSEC1 node, so Linux should not try to probe it. Signed-off-by:
-
Anton Vorontsov authored
We must not use MPC831X_SICR[HL]_* definitions for the MPC8315 processors, because SICR USB bits locations are not compatible with MPC8313. This patch fixes ULPI workability on MPC8315E-RDB boards. Signed-off-by:
-
John Rigby authored
This allows other platforms with the same pci block like MPC5121 to use it. Signed-off-by:
John Rigby <jrigby@freescale.com> Acked-by:
Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
-
John Rigby authored
Choosing PCI or not at config time is allowed on some platforms via an if expression in arch/powerpc/Kconfig. To add a new platform with PCI support selectable at config time, you must change the if expression. This patch makes this easier by changing: bool "PCI support" if <long expression> to bool "PCI support" if PPC_PCI_CHOICE and adding select PPC_PCI_CHOICE to all the config nodes that were previously in the PCI if expression. Platforms with unconditional PCI support continue to just select PCI in their config nodes. Signed-off-by: -
Paul Gortmaker authored
The mpc7448hpc2 board doesn't have an alias block like most of the other modern eval boards have. We need this block in order to have u-boot be able to make use of the CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node) in the future. Also remove the old, redundant chosen node. Of all the modern Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only one which still has it. Its presence also breaks with some older versions of u-boot, like 1.3.1 -- which try and insert a second chosen node. Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Scott Wood authored
Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Scott Wood authored
Basic PM support for 83xx. Standby is implemented as sleep. Suspend-to-RAM is implemented as "deep sleep" (with the processor turned off) on 831x. Signed-off-by:
-
Scott Wood authored
Convert to DTS version 1, eliminate some obsolete practices, and correct some errors (compared to the actual 8540 device tree). Signed-off-by:
-
Scott Wood authored
Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmcLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (68 commits) sdio_uart: Fix SDIO break control to now return success or an error mmc: host driver for Ricoh Bay1Controllers sdio: sdio_io.c Fix sparse warnings sdio: fix the use of hard coded timeout value. mmc: OLPC: update vdd/powerup quirk comment mmc: fix spares errors of sdhci.c mmc: remove multiwrite capability wbsd: fix bad dma_addr_t conversion atmel-mci: Driver for Atmel on-chip MMC controllers mmc: fix sdio_io sparse errors mmc: wbsd.c fix shadowing of 'dma' variable MMC: S3C24XX: Refuse incorrectly aligned transfers MMC: S3C24XX: Add maintainer entry MMC: S3C24XX: Update error debugging. MMC: S3C24XX: Add media presence test to request handling. MMC: S3C24XX: Fix use of msecs where jiffies are needed MMC: S3C24XX: Add MODULE_ALIAS() entries for the platform devices MMC: S3C24XX: Fix s3c2410_dma_request() return code check. MMC: S3C24XX: Allow card-detect on non-IRQ capable pin MMC: S3C24XX: Ensure host->mrq->data is valid ... Manually fixed up bogus executable bits on drivers/mmc/core/sdio_io.c and include/linux/mmc/sdio_func.h when merging.
-
git://git.infradead.org/~dedekind/ubifs-2.6Linus Torvalds authored
* 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6: UBIFS: include to compilation UBIFS: add new flash file system UBIFS: add brief documentation MAINTAINERS: add UBIFS section do_mounts: allow UBI root device name VFS: export sync_sb_inodes VFS: move inode_lock into sync_sb_inodes
-
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (76 commits) IDE: Report errors during drive reset back to user space Update documentation of HDIO_DRIVE_RESET ioctl IDE: Remove unused code IDE: Fix HDIO_DRIVE_RESET handling hd.c: remove the #include <linux/mc146818rtc.h> update the BLK_DEV_HD help text move ide/legacy/hd.c to drivers/block/ ide/legacy/hd.c: use late_initcall() remove BLK_DEV_HD_ONLY ide: endian annotations in ide-floppy.c ide-floppy: zero out the whole struct ide_atapi_pc on init ide-floppy: fold idefloppy_create_test_unit_ready_cmd into idefloppy_open ide-cd: move request prep chunk from cdrom_do_newpc_cont to rq issue path ide-cd: move request prep from cdrom_start_rw_cont to rq issue path ide-cd: move request prep from cdrom_start_seek_continuation to rq issue path ide-cd: fold cdrom_start_seek into ide_cd_do_request ide-cd: simplify request issuing path ide-cd: mv ide_do_rw_cdrom ide_cd_do_request ide-cd: cdrom_start_seek: remove unused argument block ide-cd: ide_do_rw_cdrom: add the catch-all bad request case to the if-else block ...
-
Linus Torvalds authored
Merge branch 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-merge-2.6 * 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-merge-2.6: (87 commits) Fix FADT parsing Add the ability to reset the machine using the RESET_REG in ACPI's FADT table. ACPI: use dev_printk when possible PNPACPI: add support for HP vendor-specific CCSR descriptors PNP: avoid legacy IDE IRQs PNP: convert resource options to single linked list ISAPNP: handle independent options following dependent ones PNP: remove extra 0x100 bit from option priority PNP: support optional IRQ resources PNP: rename pnp_register_*_resource() local variables PNPACPI: ignore _PRS interrupt numbers larger than PNP_IRQ_NR PNP: centralize resource option allocations PNP: remove redundant pnp_can_configure() check PNP: make resource assignment functions return 0 (success) or -EBUSY (failure) PNP: in debug resource dump, make empty list obvious PNP: improve resource assignment debug PNP: increase I/O port & memory option address sizes PNP: introduce pnp_irq_mask_t typedef PNP: make resource option structures private to PNP subsystem PNP: define PNP-specific IORESOURCE_IO_* flags alongside IRQ, DMA, MEM ...
-
Martin K. Petersen authored
Fail integrity check gracefully when request does not have a bio attached (BLOCK_PC). Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.linux-nfs.org/projects/trondmy/nfs-2.6Linus Torvalds authored
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (82 commits) NFSv4: Remove BKL from the nfsv4 state recovery SUNRPC: Remove the BKL from the callback functions NFS: Remove BKL from the readdir code NFS: Remove BKL from the symlink code NFS: Remove BKL from the sillydelete operations NFS: Remove the BKL from the rename, rmdir and unlink operations NFS: Remove BKL from NFS lookup code NFS: Remove the BKL from nfs_link() NFS: Remove the BKL from the inode creation operations NFS: Remove BKL usage from open() NFS: Remove BKL usage from the write path NFS: Remove the BKL from the permission checking code NFS: Remove attribute update related BKL references NFS: Remove BKL requirement from attribute updates NFS: Protect inode->i_nlink updates using inode->i_lock nfs: set correct fl_len in nlmclnt_test() SUNRPC: Support registering IPv6 interfaces with local rpcbind daemon SUNRPC: Refactor rpcb_register to make rpcbindv4 support easier SUNRPC: None of rpcb_create's callers wants a privileged source port SUNRPC: Introduce a specific rpcb_create for contacting localhost ...
-
Jan Beulich authored
The (1.0 inherited) separate length fields in the FADT are byte granular. Further, PM1a/b may have distinct lengths and live in distinct address spaces. acpi_tb_convert_fadt() should account for all of these conditions. Apart from these changes I'm puzzled by the fact that, not just for acpi_gbl_xpm1{a,b}_enable, acpi_hw_low_level_{read,write}() get an explicit size passed rather than using the size found in the passed GAS. What happens on a platform that defines PM1{a,b} wider than 16 bits? Of course, acpi_hw_low_level_{read,write}() at present are entirely un-prepared to deal with sizes other than 8, 16, or 32, not to speak of a non-zero bit_offset or access_width... Signed-off-by:Jan Beulich <jbeulich@novell.com> Signed-off-by:
Andi Kleen <ak@linux.intel.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org>
-
Aaron Durbin authored
Signed-off-by:
Aaron Durbin <adurbin@google.com> Signed-off-by:
-
Bjorn Helgaas authored
Convert printks to use dev_printk(). The most obvious change will be messages like this: -ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 31 (level, low) -> IRQ 31 +cciss 0000:00:04.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 Signed-off-by:
Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by:
Len Brown <len.brown@intel.com> Signed-off-by:
-
Bjorn Helgaas authored
The HP CCSR descriptor describes MMIO address space that should appear as a MEM resource. This patch adds support for parsing these descriptors in the _CRS data. The visible effect of this is that these MEM resources will appear in /sys/devices/pnp0/.../resources, which means that "lspnp -v" will report it, user applications can use this to locate device CSR space, and kernel drivers can use the normal PNP resource accessors to locate them. Signed-off-by:
-
Bjorn Helgaas authored
If an IDE controller is in compatibility mode, it expects to use IRQs 14 and 15, so PNP should avoid them. This patch should resolve this problem report: parallel driver grabs IRQ14 preventing legacy SFF ATA controller from working https://bugzilla.novell.com/show_bug.cgi?id=375836Signed-off-by:
-
Bjorn Helgaas authored
ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of a device, i.e., the possibilities an OS bus driver has when it assigns I/O port, MMIO, and other resources to the device. PNP used to maintain this "possible resource setting" information in one independent option structure and a list of dependent option structures for each device. Each of these option structures had lists of I/O, memory, IRQ, and DMA resources, for example: dev independent options ind-io0 -> ind-io1 ... ind-mem0 -> ind-mem1 ... ... dependent option set 0 dep0-io0 -> dep0-io1 ... dep0-mem0 -> dep0-mem1 ... ... dependent option set 1 dep1-io0 -> dep1-io1 ... dep1-mem0 -> dep1-mem1 ... ... ... This data structure was designed for ISAPNP, where the OS configures device resource settings by writing directly to configuration registers. The OS can write the registers in arbitrary order much like it writes PCI BARs. However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces that perform device configuration, and it is important to pass the desired settings to those interfaces in the correct order. The OS learns the correct order by using firmware interfaces that return the "current resource settings" and "possible resource settings," but the option structures above doesn't store the ordering information. This patch replaces the independent and dependent lists with a single list of options. For example, a device might have possible resource settings like this: dev options ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ... All the possible settings are in the same list, in the order they come from the firmware "possible resource settings" list. Each entry is tagged with an independent/dependent flag. Dependent entries also have a "set number" and an optional priority value. All dependent entries must be assigned from the same set. For example, the OS can use all the entries from dependent set 0, or all the entries from dependent set 1, but it cannot mix entries from set 0 with entries from set 1. Prior to this patch PNP didn't keep track of the order of this list, and it assigned all independent options first, then all dependent ones. Using the example above, that resulted in a "desired configuration" list like this: ind->io0 -> ind->io1 -> depN-io0 ... instead of the list the firmware expects, which looks like this: ind->io0 -> depN-io0 -> ind-io1 ... Signed-off-by:Rene Herman <rene.herman@gmail.com> Signed-off-by:
-
Bjorn Helgaas authored
The ISAPNP spec recommends that independent options precede dependent ones, but this is not actually required. The current ISAPNP code incorrectly puts such trailing independent options at the end of the last dependent option list. This patch fixes that bug by resetting the current option list to the independent list when we see an "End Dependent Functions" tag. PNPBIOS and PNPACPI handle this the same way. Signed-off-by:
-
Bjorn Helgaas authored
When building resource options, ISAPNP and PNPBIOS set the priority to something like "0x100 | PNP_RES_PRIORITY_ACCEPTABLE", but we immediately mask off the 0x100 again in pnp_build_option(), so that bit looks superfluous. Thanks to Rene Herman <rene.herman@gmail.com> for pointing this out. Signed-off-by:
-
Bjorn Helgaas authored
This patch adds an IORESOURCE_IRQ_OPTIONAL flag for use when assigning resources to a device. If the flag is set and we are unable to assign an IRQ to the device, we can leave the IRQ disabled but allow the overall resource allocation to succeed. Some devices request an IRQ, but can run without an IRQ (possibly with degraded performance). This flag lets us run the device without the IRQ instead of just leaving the device disabled. This is a reimplementation of this previous change by Rene Herman <rene.herman@gmail.com>: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3b73a223661ed137c5d3d2635f954382e94f5a43 I reimplemented this for two reasons: - to prepare for converting all resource options into a single linked list, as opposed to the per-resource-type lists we have now, and - to preserve the order and number of resource options. In PNPBIOS and ACPI, we configure a device by giving firmware a list of resource assignments. It is important that this list has exactly the same number of resources, in the same order, as the "template" list we got from the firmware in the first place. The problem of a sound card MPU401 being left disabled for want of an IRQ was reported by Uwe Bugla <uwe.bugla@gmx.de>. Signed-off-by: -
Bjorn Helgaas authored
No functional change; just rename "data" to something more descriptive. Signed-off-by:
-
Bjorn Helgaas authored
ACPI Extended Interrupt Descriptors can encode 32-bit interrupt numbers, so an interrupt number may exceed the size of the bitmap we use to track possible IRQ settings. To avoid corrupting memory, complain and ignore too-large interrupt numbers. There's similar code in pnpacpi_parse_irq_option(), but I didn't change that because the small IRQ descriptor can only encode IRQs 0-15, which do not exceed bitmap size. In the future, we could handle IRQ numbers greater than PNP_IRQ_NR by replacing the bitmap with a table or list. Signed-off-by:
-
Bjorn Helgaas authored
This patch moves all the option allocations (pnp_mem, pnp_port, etc) into the pnp_register_{mem,port,irq,dma}_resource() functions. This will make it easier to rework the option data structures. The non-trivial part of this patch is the IRQ handling. The backends have to allocate a local pnp_irq_mask_t bitmap, populate it, and pass a pointer to pnp_register_irq_resource(). Signed-off-by: -
Bjorn Helgaas authored
pnp_assign_resources() is static and the only caller checks pnp_can_configure() before calling it, so no need to do it again. Signed-off-by:
-
Bjorn Helgaas authored
This patch doesn't change any behavior; it just makes the return values more conventional. This changes pnp_assign_dma() from a void function to one that returns an int, just like the other assignment functions. For now, at least, pnp_assign_dma() always returns 0 (success), so it appears to never fail, just like before. Signed-off-by:
-
Bjorn Helgaas authored
If the resource list is empty, say that explicitly. Previously, it was confusing because often the heading was followed by zero resource lines, then some "add resource" lines from auto-assignment, so the "add" lines looked like current resources. Signed-off-by:
-
Bjorn Helgaas authored
When we fail to assign an I/O or MEM resource, include the min/max in the debug output to help match it with the options. Signed-off-by:
-
Bjorn Helgaas authored
ACPI Address Space Descriptors can be up to 64 bits wide. We should keep track of the whole thing when parsing resource options, so this patch changes PNP port and mem option fields from "unsigned short" and "unsigned int" to "resource_size_t". Signed-off-by:
-
Bjorn Helgaas authored
This adds a typedef for the IRQ bitmap, which should cause no functional change, but will make it easier to pass a pointer to a bitmap to pnp_register_irq_resource(). Signed-off-by:
-
Bjorn Helgaas authored
Nothing outside the PNP subsystem should need access to a device's resource options, so this patch moves the option structure declarations to a private header file. Signed-off-by:
-
Bjorn Helgaas authored
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED in a private header file, but put those flags in struct resource.flags fields. Better to make them IORESOURCE_IO_* flags like the existing IRQ, DMA, and MEM flags. Signed-off-by:
-
Bjorn Helgaas authored
No functional change; just make a couple declarations consistent with the rest of the file. Signed-off-by:
-
Bjorn Helgaas authored
As part of a heuristic to identify modem devices, 8250_pnp.c checks to see whether a device can be configured at any of the legacy COM port addresses. This patch moves the code that traverses the PNP "possible resource options" from 8250_pnp.c to the PNP subsystem. This encapsulation is important because a future patch will change the implementation of those resource options. Signed-off-by:
-
