Commit b67a1064 authored by Mark Lord's avatar Mark Lord Committed by Jeff Garzik

sata_mv fix ifctl handling

Fix handling of the SATA_INTERFACE_CFG register to match datasheet requirements.
Signed-off-by: default avatarMark Lord <mlord@pobox.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent b562468c
......@@ -2242,6 +2242,16 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
return;
}
static void mv_setup_ifctl(void __iomem *port_mmio, int want_gen2i)
{
u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG);
ifctl = (ifctl & 0xf7f) | 0x9b1000; /* from chip spec */
if (want_gen2i)
ifctl |= (1 << 7); /* enable gen2i speed */
writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG);
}
/*
* Caller must ensure that EDMA is not active,
* by first doing mv_stop_edma() where needed.
......@@ -2253,18 +2263,17 @@ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
if (IS_GEN_II(hpriv)) {
u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG);
ifctl |= (1 << 7); /* enable gen2i speed */
ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */
writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG);
if (!IS_GEN_I(hpriv)) {
/* Enable 3.0gb/s link speed */
mv_setup_ifctl(port_mmio, 1);
}
udelay(25); /* allow reset propagation */
/* Spec never mentions clearing the bit. Marvell's driver does
* clear the bit, however.
/*
* Strobing ATA_RST here causes a hard reset of the SATA transport,
* link, and physical layers. It resets all SATA interface registers
* (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev.
*/
writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS);
udelay(25); /* allow reset propagation */
writelfl(0, port_mmio + EDMA_CMD_OFS);
hpriv->ops->phy_errata(hpriv, mmio, port_no);
......@@ -2710,19 +2719,6 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
hpriv->ops->reset_bus(host, mmio);
hpriv->ops->enable_leds(hpriv, mmio);
for (port = 0; port < host->n_ports; port++) {
if (IS_GEN_II(hpriv)) {
void __iomem *port_mmio = mv_port_base(mmio, port);
u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG);
ifctl |= (1 << 7); /* enable gen2i speed */
ifctl = (ifctl & 0xfff) | 0x9b1000; /* from chip spec */
writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG);
}
hpriv->ops->phy_errata(hpriv, mmio, port);
}
for (port = 0; port < host->n_ports; port++) {
struct ata_port *ap = host->ports[port];
void __iomem *port_mmio = mv_port_base(mmio, port);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment