ahci/pata_jmicron: fix JMicron quirk

For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set.  This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.

The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits.  If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.

This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/ata/pata_jmicron.c

@@ -204,20 +204,12 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 
 	u32 reg;
 
-	if (id->driver_data != 368) {
-		/* Put the controller into AHCI mode in case the AHCI driver
-		   has not yet been loaded. This can be done with either
-		   function present */
+	/* PATA controller is fn 1, AHCI is fn 0 */
+	if (id->driver_data != 368 && PCI_FUNC(pdev->devfn) != 1)
+		return -ENODEV;
 
-		/* FIXME: We may want a way to override this in future */
-		pci_write_config_byte(pdev, 0x41, 0xa1);
-
-		/* PATA controller is fn 1, AHCI is fn 0 */
-		if (PCI_FUNC(pdev->devfn) != 1)
-			return -ENODEV;
-	}
-	if ( id->driver_data == 365 || id->driver_data == 366) {
-		/* The 365/66 have two PATA channels, redirect the second */
+	/* The 365/66 have two PATA channels, redirect the second */
+	if (id->driver_data == 365 || id->driver_data == 366) {
 		pci_read_config_dword(pdev, 0x80, &reg);
 		reg |= (1 << 24);	/* IDE1 to PATA IDE secondary */
 		pci_write_config_dword(pdev, 0x80, reg);

drivers/pci/quirks.c

@@ -1262,8 +1262,8 @@ static void quirk_jmicron_dualfn(struct pci_dev *pdev)
 			pci_read_config_dword(pdev, 0x40, &conf);
 			/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
 			/* Set the class codes correctly and then direct IDE 0 */
-			conf &= ~0x000F0200;	/* Clear bit 9 and 16-19 */
-			conf |=  0x00C20002;	/* Set bit 1, 17, 22, 23 */
+			conf &= ~0x000FF200; /* Clear bit 9 and 12-19 */
+			conf |=  0x00C2A102; /* Set 1, 8, 13, 15, 17, 22, 23 */
 			pci_write_config_dword(pdev, 0x40, conf);
 
 			/* Reconfigure so that the PCI scanner discovers the