i2c: Merge omap i2c drivers from omap-historic

Merge omap i2c drivers from omap-historic
Signed-off-by: Tony Lindgren <tony@atomide.com>

drivers/i2c/Kconfig

@@ -5,6 +5,7 @@
 menuconfig I2C
 	tristate "I2C support"
 	depends on HAS_IOMEM
+	default y if MACH_OMAP_H3 || MACH_OMAP_OSK
 	---help---
 	  I2C (pronounce: I-square-C) is a slow serial bus protocol used in
 	  many micro controller applications and developed by Philips.  SMBus,

drivers/i2c/busses/Makefile

@@ -52,6 +52,7 @@ obj-$(CONFIG_I2C_VIAPRO)	+= i2c-viapro.o
 obj-$(CONFIG_I2C_VOODOO3)	+= i2c-voodoo3.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
 obj-$(CONFIG_SCx200_I2C)	+= scx200_i2c.o
+obj-$(CONFIG_I2C_OMAP)          += i2c-omap.o
 
 ifeq ($(CONFIG_I2C_DEBUG_BUS),y)
 EXTRA_CFLAGS += -DDEBUG

drivers/i2c/busses/i2c-omap.c

@@ -36,6 +36,10 @@
 
 #include <asm/io.h>
 
+/* Hack to enable zero length transfers and smbus quick until clean fix
+   is available */
+#define OMAP_HACK
+
 /* timeout waiting for the controller to respond */
 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000))
 
@@ -285,12 +289,16 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 			     struct i2c_msg *msg, int stop)
 {
 	struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
+#ifdef OMAP_HACK
+	u8 zero_byte = 0;
+#endif
 	int r;
 	u16 w;
 
 	dev_dbg(dev->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n",
 		msg->addr, msg->len, msg->flags, stop);
 
+#ifndef OMAP_HACK
 	if (msg->len == 0)
 		return -EINVAL;
 
@@ -300,6 +308,27 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 	dev->buf = msg->buf;
 	dev->buf_len = msg->len;
 
+#else
+
+	omap_i2c_write_reg(dev, OMAP_I2C_SA_REG, msg->addr);
+	/* REVISIT: Remove this hack when we can get I2C chips from board-*.c
+	 *	    files
+	 * Sigh, seems we can't do zero length transactions. Thus, we
+	 * can't probe for devices w/o actually sending/receiving at least
+	 * a single byte. So we'll set count to 1 for the zero length
+	 * transaction case and hope we don't cause grief for some
+	 * arbitrary device due to random byte write/read during
+	 * probes.
+	 */
+	if (msg->len == 0) {
+		dev->buf = &zero_byte;
+		dev->buf_len = 1;
+	} else {
+		dev->buf = msg->buf;
+		dev->buf_len = msg->len;
+	}
+#endif
+
 	omap_i2c_write_reg(dev, OMAP_I2C_CNT_REG, dev->buf_len);
 
 	init_completion(&dev->cmd_complete);
@@ -314,8 +343,8 @@ static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
 		w |= OMAP_I2C_CON_STP;
 	omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, w);
 
-	r = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
-						      OMAP_I2C_TIMEOUT);
+	r = wait_for_completion_timeout(&dev->cmd_complete,
+					OMAP_I2C_TIMEOUT);
 	dev->buf_len = 0;
 	if (r < 0)
 		return r;
@@ -383,7 +412,11 @@ out:
 static u32
 omap_i2c_func(struct i2c_adapter *adap)
 {
+#ifndef OMAP_HACK
 	return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
+#else
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+#endif
 }
 
 static inline void
@@ -478,9 +511,14 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			if (dev->buf_len) {
 				*dev->buf++ = w;
 				dev->buf_len--;
-				if (dev->buf_len) {
-					*dev->buf++ = w >> 8;
-					dev->buf_len--;
+				/*
+				 * Data reg in 2430 is 8 bit wide,
+				 */
+				if (!cpu_is_omap2430()) {
+					if (dev->buf_len) {
+						*dev->buf++ = w >> 8;
+						dev->buf_len--;
+					}
 				}
 			} else
 				dev_err(dev->dev, "RRDY IRQ while no data"
@@ -493,9 +531,14 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			if (dev->buf_len) {
 				w = *dev->buf++;
 				dev->buf_len--;
-				if (dev->buf_len) {
-					w |= *dev->buf++ << 8;
-					dev->buf_len--;
+				/*
+				 * Data reg in 2430 is 8 bit wide,
+				 */
+				if (!cpu_is_omap2430()) {
+					if (dev->buf_len) {
+						w |= *dev->buf++ << 8;
+						dev->buf_len--;
+					}
 				}
 			} else
 				dev_err(dev->dev, "XRDY IRQ while no"

drivers/i2c/chips/Kconfig

@@ -100,6 +100,32 @@ config TPS65010
 	  This driver can also be built as a module.  If so, the module
 	  will be called tps65010.
 
+config SENSORS_TLV320AIC23
+	tristate "Texas Instruments TLV320AIC23 Codec"
+	depends on I2C && I2C_OMAP
+	help
+	  If you say yes here you get support for the I2C control
+	  interface for Texas Instruments TLV320AIC23 audio codec.
+
+config GPIOEXPANDER_OMAP
+	bool "GPIO Expander PCF8574PWR for OMAP"
+	depends on I2C && (ARCH_OMAP16XX || ARCH_OMAP24XX)
+	help
+	  If you say yes here you get support for I/O expander calls
+	  to configure IrDA, Camera and audio devices.
+
+config MENELAUS
+	bool "Menelaus PM chip"
+	depends on I2C=y && ARCH_OMAP24XX
+	help
+	  Say yes here if you have Menelaus chip on your board
+
+config TWL4030_CORE
+	bool "TI's TWL4030 companion chip Core Driver Support"
+	depends on I2C=y && ARCH_OMAP24XX
+	help
+	  Say yes here if you have TWL4030 chip on your board
+
 config SENSORS_M41T00
 	tristate "ST M41T00 RTC chip"
 	depends on PPC32

drivers/i2c/chips/Makefile

@@ -12,6 +12,11 @@ obj-$(CONFIG_SENSORS_PCF8574)	+= pcf8574.o
 obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
 obj-$(CONFIG_ISP1301_OMAP)	+= isp1301_omap.o
 obj-$(CONFIG_TPS65010)		+= tps65010.o
+obj-$(CONFIG_SENSORS_TLV320AIC23) += tlv320aic23.o
+obj-$(CONFIG_GPIOEXPANDER_OMAP)	+= gpio_expander_omap.o
+obj-$(CONFIG_MENELAUS)		+= menelaus.o
+obj-$(CONFIG_TWL4030_CORE)      += twl4030_core.o
+obj-$(CONFIG_RTC_X1205_I2C)	+= x1205.o
 
 ifeq ($(CONFIG_I2C_DEBUG_CHIP),y)
 EXTRA_CFLAGS += -DDEBUG

drivers/i2c/chips/gpio_expander_omap.c

+/*
+ * drivers/i2c/chips/gpio_expander_omap.c
+ *
+ * Copyright (C) 2004 Texas Instruments Inc
+ * Author:
+ *
+ * gpio expander is used to configure IrDA, camera and audio devices on omap 1710 processor.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+#include <linux/errno.h>
+
+int read_gpio_expa(u8 * val, int addr);
+int write_gpio_expa(u8 val, int addr);
+
+int write_gpio_expa(u8 val, int addr)
+{
+	struct i2c_adapter *adap;
+	int err;
+	struct i2c_msg msg[1];
+	unsigned char data[1];
+
+	adap = i2c_get_adapter(0);
+	if (!adap)
+		return -ENODEV;
+	msg->addr = addr;	/* I2C address of GPIO EXPA */
+	msg->flags = 0;
+	msg->len = 1;
+	msg->buf = data;
+	data[0] = val;
+	err = i2c_transfer(adap, msg, 1);
+	if (err >= 0)
+		return 0;
+	return err;
+}
+
+/* Read from I/O EXPANDER on the H3 board.
+ * The IO expanders need an independent I2C client driver.
+ */
+
+int read_gpio_expa(u8 * val, int addr)
+{
+	struct i2c_adapter *adap;
+	int err;
+	struct i2c_msg msg[1];
+	unsigned char data[1];
+
+	adap = i2c_get_adapter(0);
+	if (!adap)
+		return -ENODEV;
+	msg->addr = addr;	/* I2C address of GPIO EXPA */
+	msg->flags = I2C_M_RD;
+	msg->len = 2;
+	msg->buf = data;
+	err = i2c_transfer(adap, msg, 1);
+	*val = data[0];
+
+	if (err >= 0)
+		return 0;
+	return err;
+}
+
+EXPORT_SYMBOL(read_gpio_expa);
+EXPORT_SYMBOL(write_gpio_expa);
+

drivers/i2c/chips/isp1301_omap.c

@@ -35,7 +35,11 @@
 #include <linux/workqueue.h>
 
 #include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/gpio.h>
 #include <asm/arch/usb.h>
+#include <asm/arch/mux.h>
 
 
 #ifndef	DEBUG
@@ -44,7 +48,7 @@
 
 
 #define	DRIVER_VERSION	"24 August 2004"
-#define	DRIVER_NAME	(isp1301_driver.name)
+#define	DRIVER_NAME	(isp1301_driver.driver.name)
 
 MODULE_DESCRIPTION("ISP1301 USB OTG Transceiver Driver");
 MODULE_LICENSE("GPL");
@@ -55,6 +59,7 @@ struct isp1301 {
 	void			(*i2c_release)(struct device *dev);
 
 	int			irq;
+	int			irq_type;
 
 	u32			last_otg_ctrl;
 	unsigned		working:1;
@@ -63,7 +68,7 @@ struct isp1301 {
 
 	/* use keventd context to change the state for us */
 	struct work_struct	work;
-	
+
 	unsigned long		todo;
 #		define WORK_UPDATE_ISP	0	/* update ISP from OTG */
 #		define WORK_UPDATE_OTG	1	/* update OTG from ISP */
@@ -90,14 +95,11 @@ struct isp1301 {
 
 /*-------------------------------------------------------------------------*/
 
-#ifdef	CONFIG_MACH_OMAP_H2
+#if	defined(CONFIG_MACH_OMAP_H2) || \
+	defined(CONFIG_MACH_OMAP_H3)
 
 /* board-specific PM hooks */
 
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/mach-types.h>
-
 
 #if	defined(CONFIG_TPS65010) || defined(CONFIG_TPS65010_MODULE)
 
@@ -128,17 +130,30 @@ static void enable_vbus_source(struct isp1301 *isp)
 }
 
 
-/* products will deliver OTG messages with LEDs, GUI, etc */
-static inline void notresponding(struct isp1301 *isp)
+#else
+
+static void enable_vbus_draw(struct isp1301 *isp, unsigned mA)
 {
-	printk(KERN_NOTICE "OTG device not responding.\n");
+	pr_debug("%s UNIMPL\n", __FUNCTION__);
 }
 
+static void enable_vbus_source(struct isp1301 *isp)
+{
+	pr_debug("%s UNIMPL\n", __FUNCTION__);
+}
 
 #endif
 
 /*-------------------------------------------------------------------------*/
 
+/* products will deliver OTG messages with LEDs, GUI, etc */
+static inline void notresponding(struct isp1301 *isp)
+{
+	printk(KERN_NOTICE "OTG device not responding.\n");
+}
+
+/*-------------------------------------------------------------------------*/
+
 /* only two addresses possible */
 #define	ISP_BASE		0x2c
 static unsigned short normal_i2c[] = {
@@ -291,7 +306,7 @@ static void power_up(struct isp1301 *isp)
 {
 	// isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_2, MC2_GLOBAL_PWR_DN);
 	isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1, MC1_SUSPEND_REG);
-	
+
 	/* do this only when cpu is driving transceiver,
 	 * so host won't see a low speed device...
 	 */
@@ -514,6 +529,7 @@ static inline void check_state(struct isp1301 *isp, const char *tag) { }
 static void update_otg1(struct isp1301 *isp, u8 int_src)
 {
 	u32	otg_ctrl;
+	u8      int_id;
 
 	otg_ctrl = OTG_CTRL_REG
 			& OTG_CTRL_MASK
@@ -527,7 +543,10 @@ static void update_otg1(struct isp1301 *isp, u8 int_src)
 	}
 	if (int_src & INTR_VBUS_VLD)
 		otg_ctrl |= OTG_VBUSVLD;
-	if (int_src & INTR_ID_GND) {		/* default-A */
+
+	int_id = isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE);
+
+	if (int_id & INTR_ID_GND) {		/* default-A */
 		if (isp->otg.state == OTG_STATE_B_IDLE
 				|| isp->otg.state == OTG_STATE_UNDEFINED) {
 			a_idle(isp, "init");
@@ -799,7 +818,7 @@ static irqreturn_t omap_otg_irq(int irq, void *_isp)
 		/* role is host */
 		} else {
 			if (!(otg_ctrl & OTG_ID)) {
-		 		otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
+				otg_ctrl &= OTG_CTRL_MASK & ~OTG_XCEIV_INPUTS;
 				OTG_CTRL_REG = otg_ctrl | OTG_A_BUSREQ;
 			}
 
@@ -1082,7 +1101,7 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
 	/* update the OTG controller state to match the isp1301; may
 	 * trigger OPRT_CHG irqs for changes going to the isp1301.
 	 */
-	update_otg1(isp, isp_stat);
+	update_otg1(isp, stat); // pass the actual interrupt latch status
 	update_otg2(isp, isp_bstat);
 	check_state(isp, __FUNCTION__);
 #endif
@@ -1100,9 +1119,9 @@ static u8 isp1301_clear_latch(struct isp1301 *isp)
 }
 
 static void
-isp1301_work(void *data)
+isp1301_work(struct work_struct *work)
 {
-	struct isp1301	*isp = data;
+	struct isp1301	*isp = container_of(work, struct isp1301, work);
 	int		stop;
 
 	/* implicit lock:  we're the only task using this device */
@@ -1223,6 +1242,12 @@ static int isp1301_detach_client(struct i2c_client *i2c)
 	if (machine_is_omap_h2())
 		omap_free_gpio(2);
 
+	if (machine_is_omap_h3())
+		omap_free_gpio(14);
+
+	if (machine_is_omap_h4())
+		omap_free_gpio(125);
+
 	isp->timer.data = 0;
 	set_bit(WORK_STOP, &isp->todo);
 	del_timer_sync(&isp->timer);
@@ -1244,7 +1269,7 @@ static int isp1301_detach_client(struct i2c_client *i2c)
  *  - DEVICE mode, for when there's a B/Mini-B (device) connector
  *
  * As a rule, you won't have an isp1301 chip unless it's there to
- * support the OTG mode.  Other modes help testing USB controllers 
+ * support the OTG mode.  Other modes help testing USB controllers
  * in isolation from (full) OTG support, or maybe so later board
  * revisions can help to support those feature.
  */
@@ -1260,9 +1285,9 @@ static int isp1301_otg_enable(struct isp1301 *isp)
 	 * a few more interrupts than are strictly needed.
 	 */
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
-	 	INTR_VBUS_VLD | INTR_SESS_VLD | INTR_ID_GND);
+		INTR_VBUS_VLD | INTR_SESS_VLD | INTR_ID_GND);
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_FALLING,
-	 	INTR_VBUS_VLD | INTR_SESS_VLD | INTR_ID_GND);
+		INTR_VBUS_VLD | INTR_SESS_VLD | INTR_ID_GND);
 
 	dev_info(&isp->client.dev, "ready for dual-role USB ...\n");
 
@@ -1301,14 +1326,15 @@ isp1301_set_host(struct otg_transceiver *otg, struct usb_bus *host)
 
 	power_up(isp);
 
-	if (machine_is_omap_h2())
+// XXX h4 too?
+	if (machine_is_omap_h2() || machine_is_omap_h3())
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
 
 	dev_info(&isp->client.dev, "A-Host sessions ok\n");
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
-	 	INTR_ID_GND);
+		INTR_ID_GND);
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_FALLING,
-	 	INTR_ID_GND);
+		INTR_ID_GND);
 
 	/* If this has a Mini-AB connector, this mode is highly
 	 * nonstandard ... but can be handy for testing, especially with
@@ -1364,13 +1390,14 @@ isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget)
 	power_up(isp);
 	isp->otg.state = OTG_STATE_B_IDLE;
 
-	if (machine_is_omap_h2())
+// XXX h4 too?
+	if (machine_is_omap_h2() || machine_is_omap_h3())
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
 
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
-	 	INTR_SESS_VLD);
+		INTR_SESS_VLD | INTR_VBUS_VLD);
 	isp1301_set_bits(isp, ISP1301_INTERRUPT_FALLING,
-	 	INTR_VBUS_VLD);
+		INTR_VBUS_VLD | INTR_SESS_VLD);
 	dev_info(&isp->client.dev, "B-Peripheral sessions ok\n");
 	dump_regs(isp, __FUNCTION__);
 
@@ -1447,6 +1474,10 @@ isp1301_start_hnp(struct otg_transceiver *dev)
 	 * So do this part as early as possible...
 	 */
 	switch (isp->otg.state) {
+	case OTG_STATE_B_PERIPHERAL:
+		isp->otg.state = OTG_STATE_B_WAIT_ACON;
+		isp1301_defer_work(isp, WORK_UPDATE_ISP);
+		break;
 	case OTG_STATE_B_HOST:
 		isp->otg.state = OTG_STATE_B_PERIPHERAL;
 		/* caller will suspend next */
@@ -1494,12 +1525,13 @@ static int isp1301_probe(struct i2c_adapter *bus, int address, int kind)
 	if (!isp)
 		return 0;
 
-	INIT_WORK(&isp->work, isp1301_work, isp);
+	INIT_WORK(&isp->work, isp1301_work);
 	init_timer(&isp->timer);
 	isp->timer.function = isp1301_timer;
 	isp->timer.data = (unsigned long) isp;
 
 	isp->irq = -1;
+	isp->irq_type = 0;
 	isp->client.addr = address;
 	i2c_set_clientdata(&isp->client, isp);
 	isp->client.adapter = bus;
@@ -1562,23 +1594,44 @@ fail1:
 	}
 #endif
 
-	if (machine_is_omap_h2()) {
+// XXX h4 too?
+	if (machine_is_omap_h2() || machine_is_omap_h3()) {
 		/* full speed signaling by default */
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1,
 			MC1_SPEED_REG);
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2,
 			MC2_SPD_SUSP_CTRL);
+	}
 
+	if (machine_is_omap_h2()) {
 		/* IRQ wired at M14 */
 		omap_cfg_reg(M14_1510_GPIO2);
 		isp->irq = OMAP_GPIO_IRQ(2);
 		omap_request_gpio(2);
 		omap_set_gpio_direction(2, 1);
-		omap_set_gpio_edge_ctrl(2, OMAP_GPIO_FALLING_EDGE);
+		isp->irq_type = IRQF_TRIGGER_FALLING;
+	}
+
+	if (machine_is_omap_h3()) {
+		/* IRQ wired at N21 */
+		omap_cfg_reg(N21_1710_GPIO14);
+		isp->irq = OMAP_GPIO_IRQ(14);
+		omap_request_gpio(14);
+		omap_set_gpio_direction(14, 1);
+		isp->irq_type = IRQF_TRIGGER_FALLING;
+	}
+
+	if (machine_is_omap_h4()) {
+		/* IRQ wired at P14 */
+		omap_cfg_reg(P14_24XX_GPIO125);
+		isp->irq = OMAP_GPIO_IRQ(125);
+		omap_request_gpio(125);
+		omap_set_gpio_direction(125, 1);
+		isp->irq_type = IRQF_TRIGGER_LOW;
 	}
 
 	status = request_irq(isp->irq, isp1301_irq,
-			IRQF_SAMPLE_RANDOM, DRIVER_NAME, isp);
+			isp->irq_type, DRIVER_NAME, isp);
 	if (status < 0) {
 		dev_dbg(&i2c->dev, "can't get IRQ %d, err %d\n",
 				isp->irq, status);

include/asm-arm/arch-omap/twl4030.h

+/*
+ * twl4030.h - header for TWL4030 PM and audio CODEC device
+ *
+ * Copyright (C) 2005-2006 Texas Instruments, Inc.
+ *
+ * Based on tlv320aic23.c:
+ * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ *
+ */
+
+#ifndef __TWL4030_H_
+#define __TWL4030_H_
+
+/* USB ID */
+#define TWL4030_MODULE_USB		0x00
+/* AUD ID */
+#define TWL4030_MODULE_AUDIO_VOICE	0x01
+#define TWL4030_MODULE_GPIO		0x02
+#define TWL4030_MODULE_INTBR		0x03
+#define TWL4030_MODULE_PIH		0x04
+#define TWL4030_MODULE_TEST		0x05
+/* AUX ID */
+#define TWL4030_MODULE_KEYPAD		0x06
+#define TWL4030_MODULE_MADC		0x07
+#define TWL4030_MODULE_INTERRUPTS	0x08
+#define TWL4030_MODULE_LED		0x09
+#define TWL4030_MODULE_MAIN_CHARGE	0x0A
+#define TWL4030_MODULE_PRECHARGE	0x0B
+#define TWL4030_MODULE_PWM0		0x0C
+#define TWL4030_MODULE_PWM1		0x0D
+#define TWL4030_MODULE_PWMA		0x0E
+#define TWL4030_MODULE_PWMB		0x0F
+/* POWER ID */
+#define TWL4030_MODULE_BACKUP		0x10
+#define TWL4030_MODULE_INT		0x11
+#define TWL4030_MODULE_PM_MASTER	0x12
+#define TWL4030_MODULE_PM_RECIEVER	0x13
+#define TWL4030_MODULE_RTC		0x14
+#define TWL4030_MODULE_SECURED_REG	0x15
+
+/* IRQ information-need base */
+#include <asm/arch/irqs.h>
+/* TWL4030 interrupts */
+
+#define TWL4030_MODIRQ_GPIO		(IH_TWL4030_BASE + 0)
+#define TWL4030_MODIRQ_KEYPAD		(IH_TWL4030_BASE + 1)
+#define TWL4030_MODIRQ_BCI		(IH_TWL4030_BASE + 2)
+#define TWL4030_MODIRQ_MADC		(IH_TWL4030_BASE + 3)
+#define TWL4030_MODIRQ_USB		(IH_TWL4030_BASE + 4)
+#define TWL4030_MODIRQ_PWR		(IH_TWL4030_BASE + 5)
+/* Rest are unsued currently*/
+
+/* Offsets to Power Registers */
+#define TWL4030_VDAC_DEV_GRP		0x3B
+#define TWL4030_VDAC_DEDICATED		0x3E
+#define TWL4030_VAUX2_DEV_GRP		0x1B
+#define TWL4030_VAUX2_DEDICATED		0x1E
+#define TWL4030_VAUX3_DEV_GRP		0x1F
+#define TWL4030_VAUX3_DEDICATED		0x22
+
+/* Functions to read and write from TWL4030 */
+
+/*
+ * IMP NOTE:
+ * The base address of the module will be added by the triton driver
+ * It is the caller's responsibility to ensure sane values
+ */
+int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
+int twl4030_i2c_read_u8(u8 mod_no, u8* val, u8 reg);
+
+ /*
+  * i2c_write: IMPORTANT - Allocate value num_bytes+1 and valid data starts at
+  *		Offset 1.
+  */
+int twl4030_i2c_write(u8 mod_no, u8 * value, u8 reg, u8 num_bytes);
+int twl4030_i2c_read(u8 mod_no, u8 * value, u8 reg, u8 num_bytes);
+
+#endif /* End of __TWL4030_H */

include/linux/i2c-id.h

@@ -119,6 +119,8 @@
 #define I2C_DRIVERID_WM8750		90	/* Wolfson WM8750 audio codec */
 #define I2C_DRIVERID_WM8753		91	/* Wolfson WM8753 audio codec */
 
+#define I2C_DRIVERID_MISC	99	/* Whatever until sorted out	*/
+
 #define I2C_DRIVERID_I2CDEV	900
 #define I2C_DRIVERID_ARP        902    /* SMBus ARP Client              */
 #define I2C_DRIVERID_ALERT      903    /* SMBus Alert Responder Client  */