- 10 Jun, 2007 12 commits
-
-
Albert Lee authored
Always enforce correct DEV bit since we know which drive the command is targeted. SAT demands to ignore the DEV bit, too. Signed-off-by:
Albert Lee <albertcc@tw.ibm.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Albert Lee authored
Map the ATA passthru UDMA protocols to ATA_PROT_DMA. Signed-off-by:
-
Albert Lee authored
support the pass through of PIO multi commands. Signed-off-by:
-
Albert Lee authored
Update the ATA passthru protocol numbers according to the new spec. Signed-off-by:
-
Alan Cox authored
The controller is not reporting an unlawful type, it is reporting an invalid type. Illegal specifically means "prohibited by law" Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Alan Cox authored
The ata IRQ ack functions are only used when debugging. Unfortunately almost every controller that calls them can cause crashes in some configurations as there are missing checks for bmdma presence. In addition ata_port_start insists of installing DMA buffers and pad buffers for controllers regardless. The SFF controllers actually need to make that decision dynamically at controller setup time and all need the same helper - so we add ata_sff_port_start. Future patches will switch the SFF drivers to use this. Signed-off-by:
-
Peer Chen authored
Add the MCP73/MCP77 support to ahci driver. Signed-off-by:
Peer Chen <peerchen@gmail.com> Signed-off-by:
-
Tejun Heo authored
hw_sata_spd_limit used to be incorrectly initialized to zero instead of UINT_MAX if SPD is zero in SControl register. This breaks PHY speed down. Fix it. Signed-off-by:
Tejun Heo <htejun@gmail.com> Signed-off-by:
-
Albert Lee authored
For ATA/CFA devices, libata prints out the device model and firmware revision. Do the same for ATAPI devices. Signed-off-by:
-
Olof Johansson authored
Most drivers don't seem to fill out the host->irq field, resulting in the wrong (no) irq being reported at probe time. For example, sil24 on my system: ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0 Since they're allocated and set up in ata_host_activate(), just save them away there. Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Tejun Heo authored
HITACHI HTS541680J9SA00/SB21C7EP spuriously completes NCQ commands. Blacklist it for NCQ. Signed-off-by:
-
Yoichi Yuasa authored
This patch has removed unused variable in pata_ispnp. Signed-off-by:
Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Signed-off-by:
-
- 09 Jun, 2007 28 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: ocfs2: Fix invalid assertion during write on 64k pages ocfs2: Fix masklog breakage
-
Linus Torvalds authored
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [CIPSO]: Fix several unaligned kernel accesses in the CIPSO engine. [NetLabel]: consolidate the struct socket/sock handling to just struct sock [IPV4]: Do not remove idev when addresses are cleared
-
Linus Torvalds authored
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Handle PCI bridges without 'ranges' property. [SPARC64]: Include <linux/rwsem.h> instead of <asm/rwsem.h>.
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: OHCI: Fix machine check in ohci_hub_status_data USB: Fix up bogus bInterval values in endpoint descriptors USB: cxacru: ignore error trying to start ADSL in atm_start USB: cxacru: create sysfs attributes in atm_start instead of bind USB: cxacru: add Documentation file USB: UNUSUAL_DEV: Sync up some reported devices from Ubuntu USB: usb gadgets avoid le{16,32}_to_cpup() usblp: Don't let suspend to kill ->used USB: set default y for CONFIG_USB_DEVICE_CLASS -
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: firmware: remove orphaned Email kobject: use the proper printk level for kobject error Driver core: kill unused code Driver core: keep PHYSDEV for old struct class_device update Documentation/driver-model/platform.txt
-
Robert P. J. Day authored
Prevent <linux/console_struct.h> from being included more than once, otherwise you get a redefinition error if you happen to include <linux/vt_kern.h> first. Signed-off-by:
Robert P. J. Day <rpjday@mindspring.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Andy Whitcroft authored
This version brings a some new tests, and a host of changes to fix false positives, of particular note: - check for and report #if 0 - extend checking of line lengths and spacing for .pl, .sh etc - extends the pointer type checks to multiple levels - updates printk handling to track newlines - adds a wrapped patch detector - drops the leading component of the filenames - extends switch indent handling to switch statmentes rooted in the context - adds foo * bar single pointer checks This version of checkpatch.pl can be found at the following URL: http://www.shadowen.org/~apw/public/checkpatch/checkpatch.pl-0.04 Full Changelog: Andy Whitcroft (16): allow checking line lengths and spacing on other source files clean up that whitespace sanitise the input line standardising the content of quotes clean up pointer type * and space checks fix up the sanitiser so it maintains the line length apply the printk facility checks only to the first printk in a set switch/case indent checks may anchor in the context add a wrapped patch detector put the #ifdef in C file checks on ice asm volatile is acceptable check for and report #if 0 drop the leading component of the filename as patches are -p1 use the original line when reporting operator errors correct spelling of Joel's name Version: 0.04 add support for struct foo * bar checks Geert Uytterhoeven (1): Fix checkpatch.pl name in usage template Randy Dunlap (1): checkpatch: produce fewer lines of output Signed-off-by:Andy Whitcroft <apw@shadowen.org> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by:
-
Randy Dunlap authored
Add a prefix string parameter. Callers are responsible for any string length/alignment that they want to see in the output. I.e., callers should pad strings to achieve alignment if they want that. Add rowsize parameter. This is the number of raw data bytes to be printed per line. Must be 16 or 32. Add a groupsize parameter. This allows callers to dump values as 1-byte, 2-byte, 4-byte, or 8-byte numbers. Default is 1-byte numbers. If the total length is not an even multiple of groupsize, 1-byte numbers are printed. Add an "ascii" output parameter. This causes ASCII data output following the hex data output. Clean up some doc examples. Align the ASCII output on all lines that are produced by one call. Add a new interface, print_hex_dump_bytes(), that is a shortcut to print_hex_dump(), using default parameter values to print 16 bytes in byte-size chunks of hex + ASCII output, using printk level KERN_DEBUG. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by:
-
Alan Cox authored
The UFS entry was misformatted The NEC V850 links are all broken The Berkshire watchdog links are all broken Signed-off-by:
-
Randy Dunlap authored
Produce one less line of output per flagged incident. Change this: use tabs not spaces PATCH: /home/rddunlap/arcmsr1200014.patch4:756: FILE: b/drivers/scsi/arcmsr/arcmsr_hba.c:1843: + return PCI_ERS_RESULT_NEED_RESET;$ to this: use tabs not spaces #756: FILE: b/drivers/scsi/arcmsr/arcmsr_hba.c:1843: + return PCI_ERS_RESULT_NEED_RESET;$ Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by:
-
Jeff Mahoney authored
This patch changes MAINTAINERS to reflect the new location of the reiserfs development mailing list. The old list forwards to the new one. Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Signed-off-by:
-
Andrew Morton authored
We don't want to see this: > BUG: using smp_processor_id() in preemptible [00000001] code: bash/3857 > caller is oops_begin+0xb/0x6f > > Call Trace: > [<ffffffff8020ab4d>] show_trace+0x34/0x4f > [<ffffffff8020ab7a>] dump_stack+0x12/0x17 > [<ffffffff8030d92d>] debug_smp_processor_id+0xad/0xbc > [<ffffffff8042388f>] oops_begin+0xb/0x6f > [<ffffffff8042520b>] do_page_fault+0x66a/0x7c0 > [<ffffffff804234bd>] error_exit+0x0/0x84 > coming out when the kernel is trying to oops. Cc: Andi Kleen <ak@suse.de> Signed-off-by:
-
Bob Picco authored
We aren't sampling for holes in memory. Thus we encounter a section hole with empty section map pointer for SPARSEMEM and OOPs for show_mem. This issue has been seen in 2.6.21, current git and current mm. The patch below is for mainline and mm. It was boot tested for SPARSEMEM, current VMEMMAP of Andy's in mm ml and DISCONTIGMEM. A slightly different patch will be posted to stable for 2.6.21. Previous to commit f0a5a58a memory_present was called for node_start_pfn to node_end_pfn. This would cover the hole(s) with reserved pages and valid sections. Most SPARSEMEM supported arches do a pfn_valid check in show_mem before computing the page structure address. This issue was brought to my attention on IRC by Arnaldo Carvalho de Melo. Thanks to Arnaldo for testing. Signed-off-by:
Bob Picco <bob.picco@hp.com> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Andi Kleen <ak@suse.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by:
-
Alexey Kuznetsov authored
1. New entries can be added to tsk->pi_state_list after task completed exit_pi_state_list(). The result is memory leakage and deadlocks. 2. handle_mm_fault() is called under spinlock. The result is obvious. 3. results in self-inflicted deadlock inside glibc. Sometimes futex_lock_pi returns -ESRCH, when it is not expected and glibc enters to for(;;) sleep() to simulate deadlock. This problem is quite obvious and I think the patch is right. Though it looks like each "if" in futex_lock_pi() got some stupid special case "else if". :-) 4. sometimes futex_lock_pi() returns -EDEADLK, when nobody has the lock. The reason is also obvious (see comment in the patch), but correct fix is far beyond my comprehension. I guess someone already saw this, the chunk: if (rt_mutex_trylock(&q.pi_state->pi_mutex)) ret = 0; is obviously from the same opera. But it does not work, because the rtmutex is really taken at this point: wake_futex_pi() of previous owner reassigned it to us. My fix works. But it looks very stupid. I would think about removal of shift of ownership in wake_futex_pi() and making all the work in context of process taking lock. From: Thomas Gleixner <tglx@linutronix.de> Fix 1) Avoid the tasklist lock variant of the exit race fix by adding an additional state transition to the exit code. This fixes also the issue, when a task with recursive segfaults is not able to release the futexes. Fix 2) Cleanup the lookup_pi_state() failure path and solve the -ESRCH problem finally. Fix 3) Solve the fixup_pi_state_owner() problem which needs to do the fixup in the lock protected section by using the in_atomic userspace access functions. This removes also the ugly lock drop / unqueue inside of fixup_pi_state() Fix 4) Fix a stale lock in the error path of futex_wake_pi() Added some error checks for verification. The -EDEADLK problem is solved by the rtmutex fixups. Signed-off-by:Thomas Gleixner <tglx@linutronix.de> Acked-by:
Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ulrich Drepper <drepper@redhat.com> Cc: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by:
-
Thomas Gleixner authored
Alexey Kuznetsov found some problems in the pi-futex code. One of the root causes is: When a wakeup happens, we do not to stop the chain walk so we follow a not longer relevant locking chain. Drop out when this happens. Signed-off-by:
-
Thomas Gleixner authored
Alexey Kuznetsov found some problems in the pi-futex code. The major problem is a stale return value in rt_mutex_slowlock(): When the pi chain walk returns -EDEADLK, but the waiter was woken up during the phases where the locks were dropped, the rtmutex could be acquired, but due to the stale return value -EDEADLK returned to the caller. Reset the return value in the retry path. Signed-off-by:
-
Tejun Heo authored
sata_promise uses two different command modes - packet and TF. Packet mode is intelligent low-overhead mode while TF is the same old taskfile interface. As with other advanced interface (ahci/sil24), ATA_TFLAG_POLLING has no effect in packet mode. However, PIO commands are issued using TF interface in polling mode, so pdc_interrupt() considers interrupts spurious if ATA_TFLAG_POLLING is set. This is broken for polling NODATA commands because command is issued using packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING. Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued using TF interface if ATA_TFLAG_POLLING is set. This patch fixes detection failure introduced by polling SETXFERMODE. Signed-off-by:
Mikael Pettersson <mikpe@it.uu.se> Acked-by:
-
Randy Dunlap authored
__exit function is used by both init and exit routines, so it cannot be marked __init. (from allyesconfig) WARNING: drivers/built-in.o(.text+0x9b83cf): Section mismatch: reference to .exit.text: (between 'divasfunc_exit' and 'didd_callback') Signed-off-by:
Armin Schindler <armin@melware.de> Signed-off-by:
-
Jeff Dike authored
Include linux/kernel.h wherever simple_strtoul is used. This kills a compile warning in stderr_console.c and potential ones in the other files. This also fixes a bunch of style violations in exitcode.c. Signed-off-by:
Jeff Dike <jdike@linux.intel.com> Signed-off-by:
-
Jiri Slaby authored
do not return 0 in one case and return proper values in other 2. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Signed-off-by:
-
Jiri Slaby authored
this causes oops, because pci probe function calls tty_register_device for each device found. Thanks to Ingo. Signed-off-by:
-
Jiri Slaby authored
Since it's not neccesary to have MAX_PANELS on the card, don't fail to let users use this card even in this case. Stop the testing for loop instead. Thanks to Ingo. Signed-off-by:
-
Stephen Rothwell authored
into the appropriate #ifdef. Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by:
-
Ratnadeep Joshi authored
Signed-off-by:
-
Jeff Dike authored
Force KERNEL_STACK_ORDER to be at least 1 on UML/x86_64, to avoid overflows. Signed-off-by:
-
Christoph Lameter authored
Instead of returning the smallest available object return ZERO_SIZE_PTR. A ZERO_SIZE_PTR can be legitimately used as an object pointer as long as it is not deferenced. The dereference of ZERO_SIZE_PTR causes a distinctive fault. kfree can handle a ZERO_SIZE_PTR in the same way as NULL. This enables functions to use zero sized object. e.g. n = number of objects. objects = kmalloc(n * sizeof(object)); for (i = 0; i < n; i++) objects[i].x = y; kfree(objects); Signed-off-by:
Christoph Lameter <clameter@sgi.com> Acked-by:
Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by:
-
Yoann Padioleau authored
Fix various bits of obviously-busted code which we're not happening to compile, due to ifdefs. Signed-off-by:
Yoann Padioleau <padator@wanadoo.fr> Cc: Andi Kleen <ak@suse.de> Cc: Paul Mackerras <paulus@samba.org> Acked-by:
Paul Mundt <lethal@linux-sh.org> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by:
-
Christoph Lameter authored
cache_free_alien must be called regardless if we use alien caches or not. cache_free_alien() will do the right thing if there are no alien caches available. Signed-off-by:
-
