- 23 Jun, 2005 40 commits
-
-
Oleg Nesterov authored
sys_timer_settime/sys_timer_delete needs to delete k_itimer->real.timer synchronously while holding ->it_lock, which is also locked in posix_timer_fn. This patch removes timer_active/set_timer_inactive which plays with timer_list's internals in favour of using try_to_del_timer_sync(), which was introduced in the previous patch. Signed-off-by:
Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Oleg Nesterov authored
This patch splits del_timer_sync() into 2 functions. The new one, try_to_del_timer_sync(), returns -1 when it hits executing timer. It can be used in interrupt context, or when the caller hold locks which can prevent completion of the timer's handler. NOTE. Currently it can't be used in interrupt context in UP case, because ->running_timer is used only with CONFIG_SMP. Should the need arise, it is possible to kill #ifdef CONFIG_SMP in set_running_timer(), it is cheap. Signed-off-by:
-
Oleg Nesterov authored
This patch tries to solve following problems: 1. del_timer_sync() is racy. The timer can be fired again after del_timer_sync have checked all cpus and before it will recheck timer_pending(). 2. It has scalability problems. All cpus are scanned to determine if the timer is running on that cpu. With this patch del_timer_sync is O(1) and no slower than plain del_timer(pending_timer), unless it has to actually wait for completion of the currently running timer. The only restriction is that the recurring timer should not use add_timer_on(). 3. The timers are not serialized wrt to itself. If CPU_0 does mod_timer(jiffies+1) while the timer is currently running on CPU 1, it is quite possible that local interrupt on CPU_0 will start that timer before it finished on CPU_1. 4. The timers locking is suboptimal. __mod_timer() takes 3 locks at once and still requires wmb() in del_timer/run_timers. The new implementation takes 2 locks sequentially and does not need memory barriers. Currently ->base != NULL means that the timer is pending. In that case ->base.lock is used to lock the timer. __mod_timer also takes timer->lock because ->base can be == NULL. This patch uses timer->entry.next != NULL as indication that the timer is pending. So it does __list_del(), entry->next = NULL instead of list_del() when the timer is deleted. The ->base field is used for hashed locking only, it is initialized in init_timer() which sets ->base = per_cpu(tvec_bases). When the tvec_bases.lock is locked, it means that all timers which are tied to this base via timer->base are locked, and the base itself is locked too. So __run_timers/migrate_timers can safely modify all timers which could be found on ->tvX lists (pending timers). When the timer's base is locked, and the timer removed from ->entry list (which means that _run_timers/migrate_timers can't see this timer), it is possible to set timer->base = NULL and drop the lock: the timer remains locked. This patch adds lock_timer_base() helper, which waits for ->base != NULL, locks the ->base, and checks it is still the same. __mod_timer() schedules the timer on the local CPU and changes it's base. However, it does not lock both old and new bases at once. It locks the timer via lock_timer_base(), deletes the timer, sets ->base = NULL, and unlocks old base. Then __mod_timer() locks new_base, sets ->base = new_base, and adds this timer. This simplifies the code, because AB-BA deadlock is not possible. __mod_timer() also ensures that the timer's base is not changed while the timer's handler is running on the old base. __run_timers(), del_timer() do not change ->base anymore, they only clear pending flag. So del_timer_sync() can test timer->base->running_timer == timer to detect whether it is running or not. We don't need timer_list->lock anymore, this patch kills it. We also don't need barriers. del_timer() and __run_timers() used smp_wmb() before clearing timer's pending flag. It was needed because __mod_timer() did not lock old_base if the timer is not pending, so __mod_timer()->list_add() could race with del_timer()->list_del(). With this patch these functions are serialized through base->lock. One problem. TIMER_INITIALIZER can't use per_cpu(tvec_bases). So this patch adds global struct timer_base_s { spinlock_t lock; struct timer_list *running_timer; } __init_timer_base; which is used by TIMER_INITIALIZER. The corresponding fields in tvec_t_base_s struct are replaced by struct timer_base_s t_base. It is indeed ugly. But this can't have scalability problems. The global __init_timer_base.lock is used only when __mod_timer() is called for the first time AND the timer was compile time initialized. After that the timer migrates to the local CPU. Signed-off-by:Ingo Molnar <mingo@elte.hu> Signed-off-by:
Renaud Lienhart <renaud.lienhart@free.fr> Signed-off-by:
-
Nick Piggin authored
get_request_wait needn't unplug the device immediately. Signed-off-by:
Nick Piggin <nickpiggin@yahoo.com.au> Cc: Jens Axboe <axboe@suse.de> Signed-off-by:
-
Nick Piggin authored
Sprinkle around a few branch hints in the block layer. Signed-off-by:
-
Nick Piggin authored
This memory barrier is not needed because the waitqueue will only get waiters on it in the following situations: rq->count has exceeded the threshold - however all manipulations of ->count are performed under the runqueue lock, and so we will correctly pick up any waiter. Memory allocation for the request fails. In this case, there is no additional help provided by the memory barrier. We are guaranteed to eventually wake up waiters because the request allocation mempool guarantees that if the mem allocation for a request fails, there must be some requests in flight. They will wake up waiters when they are retired. Signed-off-by:
-
Tejun Heo authored
Add KERN_ERR and __FUNCTION__ to generic tag error messages, and add a comment in blk_queue_end_tag() which explains the silent failure path. Signed-off-by:
Tejun Heo <htejun@gmail.com> Acked-by:
Jens Axboe <axboe@suse.de> Signed-off-by:
-
Tejun Heo authored
Replace BLK_TAGS_PER_LONG with BITS_PER_LONG and remove unused BLK_TAGS_MASK. Signed-off-by:
-
Tejun Heo authored
blk_queue_tag->real_max_depth was used to optimize out unnecessary allocations/frees on tag resize. However, the whole thing was very broken - tag_map was never allocated to real_max_depth resulting in access beyond the end of the map, bits in [max_depth..real_max_depth] were set when initializing a map and copied when resizing resulting in pre-occupied tags. As the gain of the optimization is very small, well, almost nill, remove the whole thing. Signed-off-by:
-
Tejun Heo authored
blk_queue_start_tag() hand-coded searching for the first zero bit in the tag map. Replace it with find_first_zero_bit(). With this patch, blk_queue_star_tag() doesn't need to fill remains of tag map with 1, thus allowing it to work properly with the next remove_real_max_depth patch. Signed-off-by:
-
Domen Puncer authored
Assignment doesn't make much sense here as condition would always be true. Signed-off-by:
Domen Puncer <domen@coderock.org> Signed-off-by:
Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by:
-
Vincent Hanquez authored
Make use of the user_mode macro where it's possible. This is useful for Xen because it will need only to redefine only the macro to a hypervisor call. Signed-off-by:
Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk> Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk> Cc: Andi Kleen <ak@muc.de> Signed-off-by:
-
Vincent Hanquez authored
Add 2 macros to set and get debugreg on x86_64. This is useful for Xen because it will need only to redefine each macro to a hypervisor call. Signed-off-by:
-
Vincent Hanquez authored
Use the user_mode macro where it's possible. Signed-off-by:
-
Vincent Hanquez authored
Rename user_mode to user_mode_vm and add a user_mode macro similar to the x86-64 one. This is useful for Xen because the linux xen kernel does not runs on the same priviledge that a vanilla linux kernel, and with this we just need to redefine user_mode(). Signed-off-by:
-
Vincent Hanquez authored
Make use of the 2 new macro set_debugreg and get_debugreg. Signed-off-by:
-
Vincent Hanquez authored
Add 2 macros to set and get debugreg on x86. This is useful for Xen because it will need only to redefine each macro to a hypervisor call. Signed-off-by:
-
Natalie Protasevich authored
I suggest to change the way IRQs are handed out to PCI devices. Currently, each I/O APIC pin gets associated with an IRQ, no matter if the pin is used or not. It is expected that each pin can potentually be engaged by a device inserted into the corresponding PCI slot. However, this imposes severe limitation on systems that have designs that employ many I/O APICs, only utilizing couple lines of each, such as P64H2 chipset. It is used in ES7000, and currently, there is no way to boot the system with more that 9 I/O APICs. The simple change below allows to boot a system with say 64 (or more) I/O APICs, each providing 1 slot, which otherwise impossible because of the IRQ gaps created for unused lines on each I/O APIC. It does not resolve the problem with number of devices that exceeds number of possible IRQs, but eases up a tension for IRQs on any large system with potentually large number of devices. I only implemented this for the ACPI boot, since if the system is this big and using newer chipsets it is probably (better be!) an ACPI based system :). The change is completely "mechanical" and does not alter any internal structures or interrupt model/implementation. The patch works for both i386 and x86_64 archs. It works with MSIs just fine, and should not intervene with implementations like shared vectors, when they get worked out and incorporated. To illustrate, below is the interrupt distribution for 2-cell ES7000 with 20 I/O APICs, and an Ethernet card in the last slot, which should be eth1 and which was not configured because its IRQ exceeded allowable number (it actially turned out huge - 480!): zorro-tb2:~ # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 0: 65716 30012 30007 30002 30009 30010 30010 30010 IO-APIC-edge timer 4: 373 0 725 280 0 0 0 0 IO-APIC-edge serial 8: 0 0 0 0 0 0 0 0 IO-APIC-edge rtc 9: 0 0 0 0 0 0 0 0 IO-APIC-level acpi 14: 39 3 0 0 0 0 0 0 IO-APIC-edge ide0 16: 108 13 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb1 18: 0 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb3 19: 15 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb2 23: 3 0 0 0 0 0 0 0 IO-APIC-level ehci_hcd:usb4 96: 4240 397 18 0 0 0 0 0 IO-APIC-level aic7xxx 97: 15 0 0 0 0 0 0 0 IO-APIC-level aic7xxx 192: 847 0 0 0 0 0 0 0 IO-APIC-level eth0 NMI: 0 0 0 0 0 0 0 0 LOC: 273423 274528 272829 274228 274092 273761 273827 273694 ERR: 7 MIS: 0 Even though the system doesn't have that many devices, some don't get enabled only because of IRQ numbering model. This is the IRQ picture after the patch was applied: zorro-tb2:~ # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 0: 44169 10004 10004 10001 10004 10003 10004 6135 IO-APIC-edge timer 4: 345 0 0 0 0 244 0 0 IO-APIC-edge serial 8: 0 0 0 0 0 0 0 0 IO-APIC-edge rtc 9: 0 0 0 0 0 0 0 0 IO-APIC-level acpi 14: 39 0 3 0 0 0 0 0 IO-APIC-edge ide0 17: 4425 0 9 0 0 0 0 0 IO-APIC-level aic7xxx 18: 15 0 0 0 0 0 0 0 IO-APIC-level aic7xxx, uhci_hcd:usb3 21: 231 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb1 22: 26 0 0 0 0 0 0 0 IO-APIC-level uhci_hcd:usb2 23: 3 0 0 0 0 0 0 0 IO-APIC-level ehci_hcd:usb4 24: 348 0 0 0 0 0 0 0 IO-APIC-level eth0 25: 6 192 0 0 0 0 0 0 IO-APIC-level eth1 NMI: 0 0 0 0 0 0 0 0 LOC: 107981 107636 108899 108698 108489 108326 108331 108254 ERR: 7 MIS: 0 Not only we see the card in the last I/O APIC, but we are not even close to using up available IRQs, since we didn't waste any. Signed-off-by:Natalie Protasevich <Natalie.Protasevich@unisys.com> Acked-by:
Andi Kleen <ak@suse.de> Signed-off-by:
-
Jan Beulich authored
Eliminate duplicate definition of rdpmc in x86-64's mtrr.h. Signed-off-by:
Jan Beulich <jbeulich@novell.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by:
-
Roland McGrath authored
This is the x86_64 version of the signal fix I just posted for i386. This problem was first noticed on PPC and has already been fixed there. But the exact same issue applies to other platforms in the same way. The signal blocking for sa_mask and the handled signal takes place after the handler setup. When the stack is bogus, the handler setup forces a SIGSEGV. But then this will be blocked, and returning to user mode will fault again and iterate. This patch fixes the problem by checking whether signal handler setup failed, and not doing the signal-blocking if so. This copies what was done in the ppc code. I think all architectures' signal handler setup code follows this pattern and needs the change. Signed-off-by:
Roland McGrath <roland@redhat.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by:
-
john stultz authored
Currently the x86-64 HPET code assumes the entire HPET implementation from the spec is present. This breaks on boxes that do not implement the optional legacy timer replacement functionality portion of the spec. This patch fixes this issue, allowing x86-64 systems that cannot use the HPET for the timer interrupt and RTC to still use the HPET as a time source. I've tested this patch on a system systems without HPET, with HPET but without legacy timer replacement, as well as HPET with legacy timer replacement. This version adds a minor check to cap the HPET counter value in gettimeoffset_hpet to avoid possible time inconsistencies. Please ignore the A2 version I sent to you earlier. Acked-by:
Andi Kleen <ak@muc.de> Signed-off-by:
-
Alexander Nyberg authored
Cc: Andi Kleen <ak@muc.de> Signed-off-by:
-
Andrew Morton authored
Consolidate the mtrr sanity checking, add a dump_stack(). Signed-off-by:
-
Andrew Morton authored
x86_64's cpu_khz is unsigned int and there is no reason why x86 needs to use unsigned long. So make cpu_khz unsigned int on x86 as well. Signed-off-by:
-
Alexey Dobriyan authored
* EXPORT_SYMBOL's moved to other files * #include <linux/config.h>, <linux/module.h> where needed * #include's in i386_ksyms.c cleaned up * After copy-paste, redundant due to Makefiles rules preprocessor directives removed: #ifdef CONFIG_FOO EXPORT_SYMBOL(foo); #endif obj-$(CONFIG_FOO) += foo.o * Tiny reformat to fit in 80 columns Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Alexey Dobriyan authored
csum_and_copy_to_user is static inline and uses VERIFY_WRITE. Patch allows to remove asm/uaccess.h from i386_ksyms.c without dependency surprises. Signed-off-by:
-
Aleksey Gorelov authored
According to the VIA 82C586B datasheet (still available from http://gkernel.sourceforge.net/specs/via/586b.pdf.bz2) this chip need a special PIRQ mapping. Signed-off-by:
Karsten Keil <kkeil@suse.de> Signed-off-by:
Aleksey Gorelov <aleksey_gorelov@phoenix.com> Signed-off-by:
-
Natalie Protasevich authored
I have submitted the patch for x86_64, this is submission for i386. The patch changes the way IRQs are handed out to PCI devices. Currently, each I/O APIC pin gets associated with an IRQ, no matter if the pin is used or not. This imposes severe limitation on systems that have designs that employ many I/O APICs, only utilizing couple lines of each, such as P64H2 chipset. It is used in ES7000, and currently, there is no way to boot the system with more that 9 I/O APICs. The simple change below allows to boot a system with say 64 (or more) I/O APICs, each providing 1 slot, which otherwise impossible because of the IRQ gaps created for unused lines on each I/O APIC. It does not resolve the problem with number of devices that exceeds number of possible IRQs, but eases up a tension for IRQs on any large system with potentually large number of devices. Signed-off-by:
-
Christoph Lameter authored
It allows a selectable timer interrupt frequency of 100, 250 and 1000 HZ. Reducing the timer frequency may have important performance benefits on large systems. Signed-off-by:
Christoph Lameter <clameter@sgi.com> Signed-off-by:
-
Christoph Lameter authored
Make the timer frequency selectable. The timer interrupt may cause bus and memory contention in large NUMA systems since the interrupt occurs on each processor HZ times per second. Signed-off-by:
Christoph Lameter <christoph@lameter.com> Signed-off-by:
Shai Fultheim <shai@scalex86.org> Signed-off-by:
-
Jan Beulich authored
Allow early printk code to take advantage of the full size of the screen, not just the first 25 lines. Signed-off-by:
-
Jan Beulich authored
Get the i386 watchdog tick calculation into a state where it can also be used on CPUs with frequencies beyond 4GHz, and it consolidates the calculation into a single place (for potential furture adjustments). Signed-off-by:
-
Natalie Protasevich authored
This patch is per Andi's request to remove NO_IOAPIC_CHECK from genapic and use heuristics to prevent unique I/O APIC ID check for systems that don't need it. The patch disables unique I/O APIC ID check for Xeon-based and other platforms that don't use serial APIC bus for interrupt delivery. Andi stated that AMD systems don't need unique IO_APIC_IDs either. Signed-off-by:
-
Roland McGrath authored
This problem was first noticed on PPC and has already been fixed there. But the exact same issue applies to other platforms in the same way. The signal blocking for sa_mask and the handled signal takes place after the handler setup. When the stack is bogus, the handler setup forces a SIGSEGV. But then this will be blocked, and returning to user mode will fault again and iterate. This patch fixes the problem by checking whether signal handler setup failed, and not doing the signal-blocking if so. This copies what was done in the ppc code. I think all architectures' signal handler setup code follows this pattern and needs the change. Signed-off-by:
-
Christoph Lameter authored
Patch to allocate the control structures for for ide devices on the node of the device itself (for NUMA systems). The patch depends on the Slab API change patch by Manfred and me (in mm) and the pcidev_to_node patch that I posted today. Does some realignment too. Signed-off-by:
Justin M. Forbes <jmforbes@linuxtx.org> Signed-off-by:
Pravin Shelar <pravin@calsoftinc.com> Signed-off-by:
Shobhit Dayal <shobhit@calsoftinc.com> Signed-off-by:
-
Christoph Lameter authored
Define pcibus_to_node to be able to figure out which NUMA node contains a given PCI device. This defines pcibus_to_node(bus) in include/linux/topology.h and adjusts the macros for i386 and x86_64 that already provided a way to determine the cpumask of a pci device. x86_64 was changed to not build an array of cpumasks anymore. Instead an array of nodes is build which can be used to generate the cpumask via node_to_cpumask. Signed-off-by:
-
Christoph Lameter authored
asm-generic/topology.h must also be included if CONFIG_NUMA is set in order to provide the fall back pcibus_to_node function. Signed-off-by:
-
Hirokazu Takata authored
Use asm-generic/topology.h to fix yet another pcibus_to_node() build error. Cc: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by:
-
Venkatesh Pallipadi authored
Issue: Current tsc based delay_calibration can result in significant errors in loops_per_jiffy count when the platform events like SMIs (System Management Interrupts that are non-maskable) are present. This could lead to potential kernel panic(). This issue is becoming more visible with 2.6 kernel (as default HZ is 1000) and on platforms with higher SMI handling latencies. During the boot time, SMIs are mostly used by BIOS (for things like legacy keyboard emulation). Description: The psuedocode for current delay calibration with tsc based delay looks like (0) Estimate a value for loops_per_jiffy (1) While (loops_per_jiffy estimate is accurate enough) (2) wait for jiffy transition (jiffy1) (3) Note down current tsc (tsc1) (4) loop until tsc becomes tsc1 + loops_per_jiffy (5) check whether jiffy changed since jiffy1 or not and refine loops_per_jiffy estimate Consider the following cases Case 1: If SMIs happen between (2) and (3) above, we can end up with a loops_per_jiffy value that is too low. This results in shorted delays and kernel can panic () during boot (Mostly at IOAPIC timer initialization timer_irq_works() as we don't have enough timer interrupts in a specified interval). Case 2: If SMIs happen between (3) and (4) above, then we can end up with a loops_per_jiffy value that is too high. And with current i386 code, too high lpj value (greater than 17M) can result in a overflow in delay.c:__const_udelay() again resulting in shorter delay and panic(). Solution: The patch below makes the calibration routine aware of asynchronous events like SMIs. We increase the delay calibration time and also identify any significant errors (greater than 12.5%) in the calibration and notify it to user. Patch below changes both i386 and x86-64 architectures to use this new and improved calibrate_delay_direct() routine. Signed-off-by:
Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by:
Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Ian Campbell authored
The attached patch causes the various arch specific install.sh scripts to look for ${CROSS_COMPILE}installkernel rather than just installkernel (in both /sbin/ and ~/bin/ where the script already did this). This allows you to have e.g. arm-linux-installkernel as a handy way to install on your cross target. It also prevents the script picking up on the host /sbin/installkernel which causes the script to fall through and do the install itself (which is what I actually use myself, with $INSTALL_PATH set). I don't believe it causes back-compatibility problems since calling the host installkernel was never likely to work or be what you wanted when cross compiling anyway. If $CROSS_COMPILE isn't set then nothing changes. I only use ARM and i386 myself but I figured it couldn't hurt to do the whole lot. I've cc'd those who I hope are the arch maintainers for files that I've touched. Signed-off-by:Ian Campbell <icampbell@arcom.com> Signed-off-by:
-
