Place SMS and SDRC into smart idle mode
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is an updated patch to fix lcd for H2 board. It uses platform_data
field to pass spi_device to lcd driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>

H2 / H3 boards use this chip, update their board files.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

These were left out from the board file when merging these drivers,
add them here.

Call GPIO init from the board file as well, since the platform device init
code uses the GPIO API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Mistral-specific:

  - Add PWL-driven LCD backlight device

  - Apply power to the board even when the LCD isn't configured; things
    like EEPROM, temperature sensor, and wakeup switch depend on it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add omap osk defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update omap h2 defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch syncs omap board specific files with linux-omap tree.

Patch consists mostly of driver updates done in linux-omap
tree for drivers not yet in mainline kernel.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.

If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmz71 specific things - board file.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed, so that disabling the SoSSI clock during idle can
be prevented.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Support the camera connector on the OSK Mistral add-on board:

  - define muxing for both camera controllers
  - mux both of them for Mistral
  - teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables some clock on omap310.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable serial idling and wakeup features
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Bugfixes for the OSK led support:

 - Fix Kconfig merge glitches:  Mistral handles idle and timer leds just fine
 - Fix pm_suspend() runtime botch:  can't sleep, so can't touch tps65010 leds

Improvements:
 - Switch sense of Mistral idle led, so idle == off

Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning.  It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix unsupported one-shot mode in set_mode hook.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The manatees, they are dancing!
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some user space tools need to identify SYSV shared memory when examining
/proc/<pid>/maps.  To do so they look for a block device with major zero, a
dentry named SYSV<sysv key>, and having the minor of the internal sysv
shared memory kernel mount.

To help these tools and to make it easier for people just browsing
/proc/<pid>/maps this patch modifies hugetlb sysv shared memory to use the
SYSV<key> dentry naming convention.

User space tools will still have to be aware that hugetlb sysv shared
memory lives on a different internal kernel mount and so has a different
block device minor number from the rest of sysv shared memory.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Albert Cahalan <acahalan@gmail.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Here's another breakage as a result of shared memory stacked files :(

The NUMA policy for a VMA is determined by checking the following (in the
order given):

1) vma->vm_ops->get_policy() (if defined)
2) vma->vm_policy (if defined)
3) task->mempolicy (if defined)
4) Fall back to default_policy

By switching to stacked files for shared memory, get_policy() is now always
set to shm_get_policy which is a wrapper function.  This causes us to stop
at step 1, which yields NULL for hugetlb instead of task->mempolicy which
was the previous (and correct) result.

This patch modifies the shm_get_policy() wrapper to maintain steps 1-3 for
the wrapped vm_ops.

(akpm: the refcounting of mempolicies is busted and this patch does nothing to
improve it)
Signed-off-by: Adam Litke <agl@us.ibm.com>
Acked-by: William Irwin <bill.irwin@oracle.com>
Cc: dean gaudet <dean@arctic.org>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We have to take care that when we call udf_discard_prealloc() from
udf_clear_inode() we have to write inode ourselves afterwards (otherwise,
some changes might be lost leading to leakage of blocks, use of free blocks
or improperly aligned extents).

Also udf_discard_prealloc() does two different things - it removes
preallocated blocks and truncates the last extent to exactly match i_size.
We move the latter functionality to udf_truncate_tail_extent(), call
udf_discard_prealloc() when last reference to a file is dropped and call
udf_truncate_tail_extent() when inode is being removed from inode cache
(udf_clear_inode() call).

We cannot call udf_truncate_tail_extent() earlier as subsequent open+write
would find the last block of the file mapped and happily write to the end
of it, although the last extent says it's shorter.

[akpm@linux-foundation.org: Make checkpatch.pl happier]
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Eric Sandeen <sandeen@sandeen.net>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If ARCH_KMALLOC_MINALIGN is set to a value greater than 8 (SLUBs smallest
kmalloc cache) then SLUB may generate duplicate slabs in sysfs (yes again)
because the object size is padded to reach ARCH_KMALLOC_MINALIGN.  Thus the
size of the small slabs is all the same.

No arch sets ARCH_KMALLOC_MINALIGN larger than 8 though except mips which
for some reason wants a 128 byte alignment.

This patch increases the size of the smallest cache if
ARCH_KMALLOC_MINALIGN is greater than 8.  In that case more and more of the
smallest caches are disabled.

If we do that then the count of the active general caches that is displayed
on boot is not correct anymore since we may skip elements of the kmalloc
array.  So count them separately.

This approach was tested by Havard yesterday.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some changes done a while ago to avoid pounding on ptep_set_access_flags and
update_mmu_cache in some race situations break sun4c which requires
update_mmu_cache() to always be called on minor faults.

This patch reworks ptep_set_access_flags() semantics, implementations and
callers so that it's now responsible for returning whether an update is
necessary or not (basically whether the PTE actually changed).  This allow
fixing the sparc implementation to always return 1 on sun4c.

[akpm@linux-foundation.org: fixes, cleanups]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: David Miller <davem@davemloft.net>
Cc: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

(As reported by linux@horizon.com)

Folding is done to minimize the theoretical possibility of systematic
weakness in the particular bits of the SHA1 hash output.  The result of
this bug is that 16 out of 80 bits are un-folded.  Without a major new
vulnerability being found in SHA1, this is harmless, but still worth
fixing.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: <linux@horizon.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The x86_64 a.out.h got a definition of STACK_TOP_MAX, which interferes with
the UML version.  So, just undef it like STACK_TOP.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Distros seem to be removing PAGE_SIZE from asm/page.h.  So, the libc side of
UML should stop using it.

I replace it with UM_KERN_PAGE_SIZE, which is defined to be the same as
PAGE_SIZE on the kernel side of the house.  I could also use getpagesize(),
but it's more important that UML have the same value of PAGE_SIZE everywhere.
It's conceivable that it could be built with a larger PAGE_SIZE, and use of
getpagesize() would break that badly.

PAGE_MASK got the same treatment, as it is closely tied to PAGE_SIZE.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update two points in the SPI interface documentation:

- Update description of the "chip stays selected after message ends"
  mode.  In some cases it's required for correctness; it isn't just a
  performance tweak.  (Yes: to use this mode on mult-device busses, another
  programming interface will be needed.  One draft has been circulated
  already.)

- Clarify spi_setup(), highlighting that callers must ensure that no
  requests are queued (can't change configuration except between I/Os), and
  that the device must be deselected when this returns (which is a key part
  of why it's called during device init).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If raid1/repair (which reads all block and fixes any differences it finds)
hits a read error, it doesn't reset the bio for writing before writing
correct data back, so the read error isn't fixed, and the device probably
gets a zero-length write which it might complain about.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1/ When resyncing a degraded raid10 which has more than 2 copies of each block,
  garbage can get synced on top of good data.

2/ We round the wrong way in part of the device size calculation, which
  can cause confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/fuse/inode.c:658:3: error: Initializer entry defined twice
fs/fuse/inode.c:661:3:   also defined here
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix oops triggered during: echo 0 > /proc/sys/kernel/nmi_watchdog

The culprit seems to be 09198e68:
[PATCH] i386: Clean up NMI watchdog code

In two places, the parameters to release_{evntsel,perfctr}_nmi
got interchanged during the cleanup.

Fix interchanged parameters to release_{evntsel,perfctr}_nmi.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix oops caused by 'cat /dev/snapshot', reported by Arkadiusz Miskiewicz,
and make it impossible to thaw tasks with the help of the swsusp userland
interface while there is a snapshot image ready to save.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix section error (allyesconfig).  The exit function is called from init,
so functions that are called by the exit function cannot be marked __exit.

WARNING: drivers/built-in.o(.text+0xe5bc6): Section mismatch: reference to .exit.
text: (between 'toshiba_acpi_exit' and 'hci_raw')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>