Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.

If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Palmz71 specific things - board file.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>

General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed, so that disabling the SoSSI clock during idle can
be prevented.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Support the camera connector on the OSK Mistral add-on board:

  - define muxing for both camera controllers
  - mux both of them for Mistral
  - teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch enables some clock on omap310.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable serial idling and wakeup features
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Bugfixes for the OSK led support:

 - Fix Kconfig merge glitches:  Mistral handles idle and timer leds just fine
 - Fix pm_suspend() runtime botch:  can't sleep, so can't touch tps65010 leds

Improvements:
 - Switch sense of Mistral idle led, so idle == off

Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning.  It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix unsupported one-shot mode in set_mode hook.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

oprofile depends on having it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

__NR_syscall_max is done in x86_64 asm-offsets; do an equivalent in
uml kern_constants.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

it depends on elimination of unreachable branches in switch (by object
size), so we must declare it always_inline
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

need it for page_private(), not all targets have it pulled indirectly
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6:
  sh64: Add .gitignore entry for syscalltab.
  sh64: generic quicklist support.
  sh64: Update cayman defconfig.
  sh64: Fixup sh-sci build.
  sh64: ppoll/pselect6() and restartable syscalls.
  sh64: dma-mapping updates.
  sh64: Fixups for the irq_regs changes.
  sh64: Wire up many new syscalls.
  spelling fixes: arch/sh64/
  sh64: ROUND_UP macro cleanup in arch/sh64/kernel/pci_sh5.c

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  Use menuconfig objects: IDE
  sl82c105: Switch to ref counting API
  ide: remove ide_use_dma()
  ide: add missing validity checks for identify words 62 and 63
  ide: remove ide_dma_enable()
  sl82c105: add speedproc() method and MWDMA0/1 support
  cs5530/sc1200: add ->speedproc support
  cs5530/sc1200: DMA support cleanup
  ide: use ide_tune_dma() part #2
  cs5530/sc1200: add ->udma_filter methods
  ide: always disable DMA before tuning it
  pdc202xx_new: use ide_tune_dma()
  alim15x3: use ide_tune_dma()
  sis5513: PIO mode setup fixes
  serverworks: PIO mode setup fixes
  pdc202xx_old: rewrite mode programming code (v2)

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  ucc_geth: eliminate max-speed, change interface-type to phy-connection-type
  smc911x: fix compilation breakage
  pasemi_mac: Fix local-mac-address parsing
  pasemi_mac: Terminate PCI ID list
  pasemi_mac: Interrupt ack fixes
  pasemi_mac: Fix register defines

It's not necessarily a very sane configuration, but people running "make
randconfig" noticed it wouldn't compile.  This fixes some obvious
problems in discontig.c to allow a clean compile.
Acked-by: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Not sure how this one got missed in the great purge some time ago but it did.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.

There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Check validity of identify words 62 and 63 before using them in
ide_get_mode_mask().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add {cs5530,sc1200}_tunepio() for programming PIO timings

* add {cs5530,sc1200}_tune_chipset() (->speedproc method) for setting
  transfer mode and convert {cs5530,sc1200}_config_dma() to use it

* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

sc1200.c:

* remove open-coded variant of ide_dma_host_off() (== ->dma_host_off),
  it is not needed because ->dma_off_quietly calls ->dma_host_off

* use ->dma_host_on (== ide_dma_host_on() for this driver) instead of
  open-coded variant, call it from the users of sc1200_config_dma2()

  [ there is no need to call ->dma_host_on in sc1200_config_dma() because
    core code takes care of calling ->ide_dma_on on successful execution
    of ->ide_dma_check ]

* add comment about ->tuneproc interface abuse

cs5530.c/sc1200.c:

* core code takes care of calling ->dma_off_quietly before calling
  ->ide_dma_check so there is no need to call it in ->ide_dma_check methods

* bump driver version
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_tune_dma() in ide-cris/it821x/pdc202xx_old/serverworks drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

CS5530/SC1200 specifies that two drives on the same cable cannot mix
UDMA/MDMA.  Add {cs5530,sc1200}_udma_filter() to handle this.  This also
makes it possible to remove open-coded best DMA mode selection and use
standard ide_use_dma()/ide_max_dma_mode() helpers.  While at it bump
version numbers.

There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_start_power_step() and set_using_dma() were missing ->dma_off_quietly
call (comment in probe_hwif() states that DMA should be always cleared before
tuning is attempted).  Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remove code enabling IORDY and prefetch from config_chipset_for_dma(),
  as the comment states it has no real effect because these settings are
  overriden when the PIO mode is set (and for this driver ->autotune == 1
  so PIO mode is always programmed)

* use ide_tune_dma() in pdcnew_config_drive_xfer_rate() and remove no longer
  needed config_chipset_for_dma()

There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ide_tune_dma() in ali15x3_config_drive_for_dma() and remove all the open
coded DMA tuning code and also config_chipset_for_dma().  Set ->atapi_dma flag
correctly in init_hwif_common_ali15x3() so ide_tune_dma() can take care of
checking if ATAPI DMA is allowed and remove open coded ATAPI DMA check from
ali15x3_config_drive_for_dma().

There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>