The iv field in des_ctx/des3_ede_ctx/serpent_ctx has never been used.
This was noticed by Dag Arne Osvik.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implementation:
===============
The encrypt/decrypt code is based on an x86 implementation I did a while
ago which I never published. This unpublished implementation does
include an assembler based key schedule and precomputed tables. For
simplicity and best acceptance, however, I took Gladman's in-kernel code
for table generation and key schedule for the kernel port of my
assembler code and modified this code to produce the key schedule as
required by my assembler implementation. File locations and Kconfig are
kept similar to the i586 AES assembler implementation.
It may seem a little bit strange to use 32 bit I/O and registers in the
assembler implementation but this gives the best code size. My
implementation takes one instruction more per round compared to
Gladman's x86 assembler but it doesn't require any stack for local
variables or saved registers and it is less serialized than Gladman's
code.
Note that all comparisons to Gladman's code were done after my code was
implemented. I did only use FIPS PUB 197 for the implementation so my
implementation is independent work.
If anybody has a better assembler solution for x86_64 I'll be pleased to
have my code replaced with the better solution.

Testing:
========
The implementation passes the in-kernel crypto testing module and I'm
running it without any problems on my laptop where it is mainly used for
dm-crypt.

Microbenchmark:
===============
The microbenchmark was done in userspace with similar compile flags as
used during kernel compile.
Encrypt/decrypt is about 35% faster than the generic C implementation.
As the generic C as well as my assembler implementation are both table
I don't really expect that there is much room for further
improvements though I'll be glad to be corrected here.
The key schedule is about 5% slower than the generic C implementation.
This is due to the fact that some more work has to be done in the key
schedule routine to fit the schedule to the assembler implementation.

Code Size:
==========
Encrypt and decrypt are together about 2.1 Kbytes smaller than the
generic C implementation which is important with regard to L1 cache
usage. The key schedule routine is about 100 bytes larger than the
generic C implementation.

Data Size:
==========
There's no difference in data size requirements between the assembler
implementation and the generic C implementation.

License:
========
Gladmans's code is dual BSD/GPL whereas my assembler code is GPLv2 only
(I'm  not going to change the license for my code). So I had to change
the module license for the x86_64 aes module from 'Dual BSD/GPL' to
'GPL' to reflect the most restrictive license within the module.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

As far as I'm aware there's a general concensus that functions that are
responsible for freeing resources should be able to cope with being passed
a NULL pointer. This makes sense as it removes the need for all callers to
check for NULL, thus elliminating the bugs that happen when some forget
(safer to just check centrally in the freeing function) and it also makes
for smaller code all over due to the lack of all those NULL checks.
This patch makes it safe to pass the crypto_free_tfm() function a NULL
pointer. Once this patch is applied we can start removing the NULL checks
from the callers.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the Padlock does CBC encryption, the memory pointed to by EAX is
not updated at all.  Instead, it updates the value of EAX by pointing
it to the last block in the output.  Therefore to maintain the correct
semantics we need to copy the IV.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though cit_iv is now always aligned, the user can still supply an
unaligned iv through crypto_cipher_encrypt_iv/crypto_cipher_decrypt_iv.
This patch will check the alignment of the user-supplied iv and copy
it if necessary.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch ensures that cit_iv is aligned according to cra_alignmask
by allocating it as part of the tfm structure.  As a side effect the
crypto layer will also guarantee that the tfm ctx area has enough space
to be aligned by cra_alignmask.  This allows us to remove the extra
space reservation from the Padlock driver.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes a needlessly global function static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

By operating on multiple blocks at once, we expect to extract more
performance out of the VIA Padlock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of the work done aes_padlock can be done in aes_set_key.  This
means that we only have to do it once when the key changes rather
than every time we perform an encryption or decryption.

This patch also sets cra_alignmask to let the upper layer ensure
that the buffers fed to us are aligned correctly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VIA Padlock device requires the input and output buffers to
be aligned on 16-byte boundaries.  This patch adds the alignmask
attribute for low-level cipher implementations to indicate their
alignment requirements.

The mid-level crypt() function will copy the input/output buffers
if they are not aligned correctly before they are passed to the
low-level implementation.

Strictly speaking, some of the software implementations require
the buffers to be aligned on 4-byte boundaries as they do 32-bit
loads.  However, it is not clear whether it is better to copy
the buffers or pay the penalty for unaligned loads/stores.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds hooks for cipher algorithms to implement multi-block
ECB/CBC operations directly.  This is expected to provide significant
performance boots to the VIA Padlock.

It could also be used for improving software implementations such as
AES where operating on multiple blocks at a time may enable certain
optimisations.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VIA Padlock device is able to perform much better when multiple
blocks are fed to it at once.  As this device offers an exceptional
throughput rate it is worthwhile to optimise the infrastructure
specifically for it.

We shift the existing page-sized fast path down to the CBC/ECB functions.
We can then replace the CBC/ECB functions with functions provided by the
underlying algorithm that performs the multi-block operations.

As a side-effect this improves the performance of large cipher operations
for all existing algorithm implementations.  I've measured the gain to be
around 5% for 3DES and 15% for AES.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking a pointer for NULL before calling kfree() on it is redundant.
This patch removes such checks from crypto/
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Missing forward declaration
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Here's a patch to fix the build issue when CONFIG_HOTPLUG is not enabled
in 2.6.13-rc2.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The membar changes made the size of __cheetah_flush_tlb_pending
grow by one instruction, but the boot-time code patching was
not updated to match.
Signed-off-by: David S. Miller <davem@davemloft.net>

The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.

Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Add explicit disabling of 440GP IRQ compatibility mode when configuring
440GX interrupt controller.  This helps when board firmware for some reason
uses this compatibility mode and leaves it enabled.  It breaks 440GX
interrupt code because it assumes native 440GX IRQ mode.  People seems to
be continuously bitten by this.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

As part of my timeofday rework, I've been looking at the NTP code and I
noticed that the PPC architecture is apparently misusing the NTP's
time_offset (it is a terrible name!) value as some form of timezone offset.

This could cause problems when time_offset changed by the NTP code.  This
patch changes the PPC code so it uses a more clear local variable:
timezone_offset.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch adds the Freescale MPC86xADS board support.  The supported
devices are SMC UART and 10Mbit ethernet on SCC1.

The manual for the board says that it "is compatible with the MPC8xxFADS
for software point of view".  That's why this patch extends FADS instead of
introducing a new platform.

FEC is not supported as the "combined FCC/FEC ethernet driver" driver by
Pantelis Antoniou should replace the current FEC driver.
Signed-off-by: Gennadiy Kurtsman <gkurtsman@ru.mvista.com>
Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Robert Olsson <Robert.Olsson@data.slu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Congestion window recover after loss depends upon the fact
that if we have a full MSS sized frame at the head of the
send queue, we will send it.  TSO deferral can defeat the
ACK clocking necessary to exit cleanly from recovery.
Signed-off-by: David S. Miller <davem@davemloft.net>

Useful in combination with classful qdiscs to drop or
temporary disable certain flows, e.g. one could block
specific ds flows with dsmark.

Unlike the noop qdisc it can be controlled by the user and
statistic accounting is done.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make TSO segment transmit size decisions at send time not earlier.

The basic scheme is that we try to build as large a TSO frame as
possible when pulling in the user data, but the size of the TSO frame
output to the card is determined at transmit time.

This is guided by tp->xmit_size_goal.  It is always set to a multiple
of MSS and tells sendmsg/sendpage how large an SKB to try and build.

Later, tcp_write_xmit() and tcp_push_one() chop up the packet if
necessary and conditions warrant.  These routines can also decide to
"defer" in order to wait for more ACKs to arrive and thus allow larger
TSO frames to be emitted.

A general observation is that TSO elongates the pipe, thus requiring a
larger congestion window and larger buffering especially at the sender
side.  Therefore, it is important that applications 1) get a large
enough socket send buffer (this is accomplished by our dynamic send
buffer expansion code) 2) do large enough writes.
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes it easier to understand, and allows easier
tweaking of the heuristic later on.
Signed-off-by: David S. Miller <davem@davemloft.net>

In tcp_clean_rtx_queue(), if the TSO packet is not even partially
acked, do not waste time calling tcp_tso_acked().
Signed-off-by: David S. Miller <davem@davemloft.net>

Everything stated there is out of data.  tcp_trim_skb()
does adjust the available socket send buffer space and
skb->truesize now.
Signed-off-by: David S. Miller <davem@davemloft.net>

Only put user data purely to pages when doing TSO.

The extra page allocations cause two problems:

1) Add the overhead of the page allocations themselves.
2) Make us do small user copies when we get to the end
   of the TCP socket cache page.

It is still beneficial to purely use pages for TSO,
so we will do it for that case.
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_snd_test() is run for every packet output by a single
call to tcp_write_xmit(), but this is not necessary.

For one, the congestion window space needs to only be
calculated one time, then used throughout the duration
of the loop.

This cleanup also makes experimenting with different TSO
packetization schemes much easier.
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_snd_test() does several different things, use inline
functions to express this more clearly.

1) It initializes the TSO count of SKB, if necessary.
2) It performs the Nagle test.
3) It makes sure the congestion window is adhered to.
4) It makes sure SKB fits into the send window.

This cleanup also sets things up so that things like the
available packets in the congestion window does not need
to be calculated multiple times by packet sending loops
such as tcp_write_xmit().
Signed-off-by: David S. Miller <davem@davemloft.net>

'nonagle' should be passed to the tcp_snd_test() function
as 'TCP_NAGLE_PUSH' if we are checking an SKB not at the
tail of the write_queue.  This is because Nagle does not
apply to such frames since we cannot possibly tack more
data onto them.

However, while doing this __tcp_push_pending_frames() makes
all of the packets in the write_queue use this modified
'nonagle' value.

Fix the bug and simplify this function by just calling
tcp_write_xmit() directly if sk_send_head is non-NULL.

As a result, we can now make tcp_data_snd_check() just call
tcp_push_pending_frames() instead of the specialized
__tcp_data_snd_check().
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_write_xmit() uses tcp_current_mss(), but some of it's callers,
namely __tcp_push_pending_frames(), already has this value available
already.

While we're here, fix the "cur_mss" argument to be "unsigned int"
instead of plain "unsigned".
Signed-off-by: David S. Miller <davem@davemloft.net>

Put the main basic block of work at the top-level of
tabbing, and mark the TCP_CLOSE test with unlikely().
Signed-off-by: David S. Miller <davem@davemloft.net>

The tcp_cwnd_validate() function should only be invoked
if we actually send some frames, yet __tcp_push_pending_frames()
will always invoke it.  tcp_write_xmit() does the call for us,
so the call here can simply be removed.

Also, tcp_write_xmit() can be marked static.
Signed-off-by: David S. Miller <davem@davemloft.net>

When we add any new packet to the TCP socket write queue,
we must call skb_header_release() on it in order for the
TSO sharing checks in the drivers to work.
Signed-off-by: David S. Miller <davem@davemloft.net>

It reimplements portions of tcp_snd_check(), so it
we move it to tcp_output.c we can consolidate it's
logic much easier in a later change.
Signed-off-by: David S. Miller <davem@davemloft.net>

This just moves the code into tcp_output.c, no code logic changes are
made by this patch.

Using this as a baseline, we can begin to untangle the mess of
comparisons for the Nagle test et al.  We will also be able to reduce
all of the redundant computation that occurs when outputting data
packets.
Signed-off-by: David S. Miller <davem@davemloft.net>