This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.

One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector.  (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.

The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.

The driver does not check if the given rate is 0, thus resulting in a
div by 0.  I think this check should be go into the clk_set_rate
framework, and not here.

Tested on AT32AP7000/ATSTK1000.

Hardware documentation can be found in the AT32AP7000 datasheet.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Split the SM platform device into separate platform devices for PM,
RTC, WDT and EIC. This is more correct according to the documentation
and allows us to simplify the code a little.

Also turn the EIC driver into a real platform driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>

Use a more conventional implementation for unaligned access, and include
an AT32AP-specific optimization:  the CPU will handle unaligned words.

The result is always faster and smaller for 8, 16, and 32 bit values.
For 64 bit quantities, it's presumably larger.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

This is a reimplementation of the zs driver for the serial subsystem.  Any
resemblance to the old driver is purely coincidential.  ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...

Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e.  ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3.  It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.

This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We can't show the extra logo from boot code if FB is built as a module.
Make the FB_LOGO_EXTRA depend on FB=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If, in dm_create_persistent(), the call to create_singlethread_workqueue()
fails then we'll return without freeing the memory allocated to 'ps', thus
leaking sizeof(struct pstore) bytes.  This patch fixes the leak.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With the slab zeroing allocations cleanups Christoph stubbed in a generic
kzalloc(), which was missed on SLOB. Follow the SLAB/SLUB changes and
kill off the __kzalloc() wrapper that SLOB was using.
Reported-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The old IDE driver is not ready to take generic SCSI commands, even if
it uses them for some specific issues (ie the tray open/close ioctls for
IDE CD-ROM's). Pointed out by Bartlomiej.

I'm sure we'll have it fixed properly soon enough, but for now we should
not allow it to cause problems.

Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I really don't see anybody else wanting to select it ;)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Fix broken logic, SIGA flags must be bitwise ORed
  [S390] cio: Dont print trailing \0 in modalias_show().
  [S390] Simplify stack trace.
  [S390] z/VM unit record device driver
  [S390] vmcp cleanup
  [S390] qdio: output queue stall on FCP and network devices
  [S390] Fix disassembly of RX_URRD, SI_URD & PC-relative instructions.
  [S390] Update default configuration.

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (21 commits)
  [WATCHDOG] at32ap700x_wdt.c - Fix compilation warnings
  [WATCHDOG] at32ap700x_wdt.c - Add spinlock support
  [WATCHDOG] at32ap700x_wdt.c - Add nowayout + MAGICCLOSE features
  [WATCHDOG] at32ap700x_wdt.c - timeout module parameter patch
  [WATCHDOG] at32ap700x_wdt.c - checkpatch.pl-0.05 clean-up's
  [WATCHDOG] change s3c2410_wdt to using dev_() macros for output
  [WATCHDOG] s3c2410_wdt announce initialisation
  [WATCHDOG] at32ap700x-wdt: add iounmap if probe function fails
  [WATCHDOG] at32ap700x-wdt: add missing iounmap in _remove
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix-2
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix
  [WATCHDOG] Watchdog driver for AT32AP700X devices
  [WATCHDOG] Mixcom Watchdog - CodingStyle clean-up
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - checkcard part 2
  [WATCHDOG] Mixcom Watchdog - checkcard
  [WATCHDOG] Mixcom Watchdog - get rid of port offset's
  [WATCHDOG] Mixcom Watchdog - update "Documentation"
  [WATCHDOG] Remove the redundant check for pwrite() in EP93XXX watchdog.
  ...

* 'bsg' of git://git.kernel.dk/data/git/linux-2.6-block:
  bsg: fix missing space in version print
  Don't define empty struct bsg_class_device if !CONFIG_BLK_DEV_BSG
  bsg: Kconfig updates
  bsg: minor cleanup
  bsg: device hash table cleanup
  bsg: fix initialization error handling bugs
  bsg: mark FUJITA Tomonori as bsg maintainer
  bsg: convert to dynamic major
  bsg: address various review comments

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix debug compilation error

* 'isdn-cleanup' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] HiSax hfc_pci: minor cleanups
  [ISDN] HiSax bkm_a4t: split setup into two smaller functions
  [ISDN] HiSax enternow: split setup into 3 smaller functions
  [ISDN] HiSax netjet_u: split setup into 3 smaller functions
  [ISDN] HiSax netjet_s: code movement, prep for hotplug
  [ISDN] HiSax: move card state alloc/setup code into separate functions
  [ISDN] HiSax: move card setup into separate function

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Kill bogus set_fs(KERNEL_DS) in do_rt_sigreturn().
  [SPARC64]: Update defconfig.
  [SPARC64]: Kill explicit %gl register reference.

* 'uninit-var' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  arch/i386/* fs/* ipc/*: mark variables with uninitialized_var()
  drivers/*: mark variables with uninitialized_var()

* 'warnings' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  drivers/atm/ambassador: kill uninit'd var warning, and fix bug
  [libata] sata_mv: use pci_try_set_mwi()
  drivers/infiniband/hw/mthca/mthca_qp: kill uninit'd var warning
  drivers/net/wan/sbni: kill uninit'd var warning
  drivers/mtd/ubi/eba: minor cleanup: tighten scope of a local var
  drivers/telephony/ixj: cleanup and fix gcc warning
  drivers/net/wan/pc300_drv: fix bug caught by gcc warning
  drivers/usb/misc/auerswald: fix status check, remove redundant check
  [netdrvr] eepro100, ne2k-pci: abort resume if pci_enable_device() fails
  [netdrvr] natsemi: Fix device removal bug
  kernel/auditfilter: kill bogus uninit'd-var compiler warning

... or we end up with header include order problems from hell.

E.g. on m68k this is 100% fatal - local_irq_enable() there
wants preempt_count(), which wants task_struct fields, which
we won't have when we are in smp.h pulled from sched.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

* trim trailing whitespace
* remove CONFIG_PCI ifdefs, this driver is always PCI (Kconfig enforced)
* remove return statements at the tail of a function
* remove indentation levels by returning an error code immediately.
  Makes the code much more readable, and easier to update to PCI hotplug
  API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.

Well, CONFIG_PCI useless ifdef was removed.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.  Prep for PCI hotplug API.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) Remove CONFIG_PCI ifdefs.  PCI is required in Kconfig.

2) Break up setup_netjet_s() into three separate internal functions.
This helps facilitate upcoming use of PCI hotplug API, and in addition
makes the code much easier to follow.

No code is changed, just moved around.  I even kept the out-of-favor
"return(0)" style used in the current source code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Just code movement.  No code changes or cleanups besides that which
is required to call the new functions from the old code site.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

No behavior changes, just code movement.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fixes the following build error:
  CC      sound/pci/mixart/mixart_hwdep.o
sound/pci/mixart/mixart_hwdep.c: In function ‘mixart_hwdep_dsp_load’:
sound/pci/mixart/mixart_hwdep.c:610: error: implicit declaration of function ‘vmalloc’
sound/pci/mixart/mixart_hwdep.c:617: error: implicit declaration of function ‘vfree’
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the following build-error:

 CC      drivers/parisc/hppb.o
drivers/parisc/hppb.c: In function ‘hppb_probe’:
drivers/parisc/hppb.c:73: error: implicit declaration of function ‘ccio_request_resource’
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Mark variables with uninitialized_var() if such a warning appears,
and analysis proves that the var is initialized properly on all paths
it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

An uninitialized variable warning illuminated an area where indeed the
variable was being used without initialization.  Unfortunately, after
verifying all such paths were fixed, the warning still appears.  So we
follow the initialization practice of other variables in this function.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Because sometimes in life, it's ok to fail.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/infiniband/hw/mthca/mthca_qp.c: In function
  ‘mthca_tavor_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1594: warning: ‘f0’ may be used
  uninitialized in this function
drivers/infiniband/hw/mthca/mthca_qp.c: In function
  ‘mthca_arbel_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1949: warning: ‘f0’ may be used
  uninitialized in this function

Initializing 'f0' is not strictly necessary in either case, AFAICS.

I was considering use of uninitialized_var(), but looking at the
complex flow of control in each function, I feel it is wiser and
safer to simply zero the var and be certain of ourselves.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

It's actually convenient in the code to initialize this and a sister
variable to zero.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) Fix gcc uninit'd var warnings by adding 'default' switch stmt labels
in two cases.  It was lightning-strikes unlikely that a problem would
ever arise, but not impossible.

2) Tighten the scope of 'blankword' in two cases.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The warning

drivers/net/wan/pc300_drv.c: In function ‘cpc_open’:
drivers/net/wan/pc300_drv.c:2942: warning: ‘br’ may be used
uninitialized in this function

was valid.  Ensure 'br' is initialized in all cases.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) We should only set 'actual_length' output variable if usb length is
known to be good.

2) No need to check actual_length for NULL.  The only caller always
passes non-NULL value.
Signed-off-by: Jeff Garzik <jeff@garzik.org>