[PATCH] PCI: Add a "enable" sysfs attribute to the pci devices to allow userspace (Xorg) to enable devices without doing foul direct access

This patch adds an "enable" sysfs attribute to each PCI device. When read it
shows the "enabled-ness" of the device, but you can write a "0" into it to
disable a device, and a "1" to enable it.

This later is needed for X and other cases where userspace wants to enable
the BARs on a device (typical example: to run the video bios on a secundary
head). Right now X does all this "by hand" via bitbanging, that's just evil.
This allows X to no longer do that but to just let the kernel do this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
CC: Peter Jones <pjones@redhat.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

PCI: Add pci_assign_resource_fixed -- allow fixed address assignments

On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.

An example of such a system would be an FPGA which is setup from user space
after the system has booted.  The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.

Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When we detect a 64-bit pre-set address in a BAR on a 32-bit platform,
we disable it and treat it as if it had been unset, thus allowing the
general address assignment code to assign a new address to it when the
device is enabled.  This can happen either if the firmware assigns
64-bit addresses; additionally, some cards have been found "in the
wild" which do not come out of reset with all the BAR registers set to
zero.

Unfortunately, the patch that implemented this tested the low part of
the address instead of the high part of the address.  This patch fixes
that.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[pci] Ignore pre-set 64-bit BARs on 32-bit platforms

Currently, Linux always rejects a device which has a pre-set 64-bit
address on a 32-bit platform.  On systems which do not do PCI
initialization in firmware, this causes some devices which don't
correctly power up with all BARs zero to fail.

This patch makes the kernel automatically zero out such an address
(thus treating it as if it had not been set at all, meaning it will
assign an address if necessary).

I have done this only for devices, not bridges.  It seems potentially
hazardous to do for bridges.
Signed-off-by: H. Peter Anvin <hpa@c2micro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

MSI callouts for altix.  Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range.  Implement this by making the above macros
global variables which the platform can override in it setup code.

Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Abstract portions of the MSI core for platforms that do not use standard
APIC interrupt controllers.  This is implemented through a new arch-specific
msi setup routine, and a set of msi ops which can be set on a per platform
basis.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add the vendor-specific extended capability PCI_CAP_ID_VNDR.  It will be
used by the Myri-10G Ethernet driver (will be submitted soon).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (30 commits)
  [PATCH] PCI Hotplug: Fix recovery path from errors during pcie_init()
  [PATCH] PCI Hotplug: fake NULL pointer dereferences in IBM Hot Plug Controller Driver
  [PATCH] shpchp: Cleanup improper info messages
  [PATCH] shpchp: Remove Unused hpc_evelnt_lock
  [PATCH] shpchp: Cleanup interrupt polling timer
  [PATCH] shpchp: Cleanup SHPC commands
  [PATCH] shpchp: Cleanup interrupt handler
  [PATCH] shpchp: Remove unnecessary hpc_ctlr_handle check
  [PATCH] pciehp: Implement get_address callback
  [PATCH] pciehp: Add missing pci_dev_put
  [PATCH] pciehp: Replace pci_find_slot() with pci_get_slot()
  [PATCH] SGI Hotplug: Incorrect power status
  [PATCH] shpchp: Create shpchpd at controller probe time
  [PATCH] shpchp: Mask Global SERR and Intr at controller release time
  [PATCH] SHPC: Fix SHPC Contoller SERR-INT Register bits access
  [PATCH] SHPC: Fix SHPC Logical Slot Register bits access
  [PATCH] SHPC: Cleanup SHPC Logical Slot Register bits access
  [PATCH] SHPC: Cleanup SHPC Logical Slot Register access
  [PATCH] SHPC: Cleanup SHPC register access
  [PATCH] pciehp: Fix programming hotplug parameters
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (85 commits)
  [SCSI] 53c700: remove reliance on deprecated cmnd fields
  [SCSI] hptiop: don't use cmnd->bufflen
  [SCSI] hptiop: HighPoint RocketRAID 3xxx controller driver
  [SCSI] aacraid: small misc. cleanups
  [SCSI] aacraid: Update supported product information
  [SCSI] aacraid: Fix return code interpretation
  [SCSI] scsi_transport_sas: fix panic in sas_free_rphy
  [SCSI] remove RQ_SCSI_* flags
  [SCSI] remove scsi_request infrastructure
  [SCSI] mptfusion: change driver revision to 3.03.10
  [SCSI] mptfc: abort of board reset leaves port dead requiring reboot
  [SCSI] mptfc: fix fibre channel infinite request/response loop
  [SCSI] mptfc: set fibre channel fw target missing timers to one second
  [SCSI] mptfusion: move fc event/reset handling to mptfc
  [SCSI] spi transport: don't allow dt to be set on SE or HVD buses
  [SCSI] aic7xxx: expose the bus setting to sysfs
  [SCSI] scsi: remove Documentation/scsi/cpqfc.txt
  [SCSI] drivers/scsi: Use ARRAY_SIZE macro
  [SCSI] Remove last page_address from dc395x.c
  [SCSI] hptiop: HighPoint RocketRAID 3xxx controller driver
  ...

Fixed up conflicts in drivers/message/fusion/mptbase.c manually (due to
the sparc interrupt cleanups)

Introduce __iowrite64_copy.  It will be used by the Myri-10G Ethernet
driver to post requests to the NIC.  This driver will be submitted soon.

__iowrite64_copy copies to I/O memory in units of 64 bits when possible (on
64 bit architectures).  It reverts to __iowrite32_copy on 32 bit
architectures.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bcollins/linux1394-2.6: (28 commits)
  eth1394: replace __constant_htons by htons
  ieee1394: adjust code formatting in highlevel.c
  ieee1394: hl_irqs_lock is taken in hardware interrupt context
  ieee1394_core: switch to kthread API
  ieee1394: sbp2: Kconfig fix
  ieee1394: add preprocessor constant for invalid csr address
  sbp2: fix deregistration of status fifo address space
  [PATCH] eth1394: endian fixes
  Fix broken suspend/resume in ohci1394
  sbp2: use __attribute__((packed)) for on-the-wire structures
  sbp2: provide helptext for CONFIG_IEEE1394_SBP2_PHYS_DMA and mark it experimental
  Update feature removal of obsolete raw1394 ISO requests.
  sbp2: fix S800 transfers if phys_dma is off
  sbp2: remove ohci1394 specific constant
  ohci1394: make phys_dma parameter read-only
  ohci1394: set address range properties
  ieee1394: extend lowlevel API for address range properties
  sbp2: log number of supported concurrent logins
  sbp2: remove manipulation of inquiry response
  ieee1394: save RAM by using a single tlabel for broadcast transactions
  ...

It also adds all the related quad routines.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The color is now in the low bits of the parent pointer, and initializing
it to 0 happens as part of the whole memset above, so just remove the
unnecessary RB_CLEAR_COLOR.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There has been an update to the forcedeth driver that added a few new
uses of xmit_lock which is no longer meant to be used directly.  This
patch replaces them with netif_tx_lock_bh.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (42 commits)
  [ARM] Fix tosa build error
  [ARM] 3610/1: Make reboot work on Versatile
  [ARM] 3609/1: S3C24XX: defconfig update for s3c2410_defconfig
  [ARM] 3591/1: Anubis: IDE device definitions
  [ARM] Include asm/hardware.h not asm/arch/hardware.h
  [ARM] 3594/1: Poodle: Add touchscreen support + other updates
  [ARM] 3564/1: sharpsl_pm: Abstract some machine specific parameters
  [ARM] 3561/1: Poodle: Correct the MMC/SD power control
  [ARM] 3593/1: Add reboot and shutdown handlers for Zaurus handhelds
  [ARM] 3599/1: AT91RM9200 remove global variables
  [ARM] 3607/1: AT91RM9200 misc fixes
  [ARM] 3605/1: AT91RM9200 Power Management
  [ARM] 3604/1: AT91RM9200 New boards
  [ARM] 3603/1: AT91RM9200 remove old files
  [ARM] 3592/1: AT91RM9200 Serial driver update
  [ARM] 3590/1: AT91RM9200 Platform devices support
  [ARM] 3589/1: AT91RM9200 DK/EK board update
  [ARM] 3588/1: AT91RM9200 CSB337/637 board update
  [ARM] 3587/1: AT91RM9200 hardware headers
  [ARM] 3586/1: AT91RM9200 header update
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ATM]: fix broken uses of NIPQUAD in net/atm
  [SCTP]: sctp_unpack_cookie() fix
  [SCTP]: Fix unintentional change to SCTP_ASSERT when !SCTP_DEBUG
  [NET]: Prevent multiple qdisc runs
  [CONNECTOR]: Initialize subsystem earlier.
  [NETFILTER]: xt_sctp: fix endless loop caused by 0 chunk length

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Update defconfig.
  [SPARC64]: Don't double-export synchronize_irq.
  [SPARC64]: Move over to GENERIC_HARDIRQS.
  [SPARC64]: Virtualize IRQ numbers.
  [SPARC64]: Kill ino_bucket->pil
  [SPARC]: Kill __irq_itoa().
  [SPARC64]: bp->pil can never be zero
  [SPARC64]: Send all device interrupts via one PIL.
  [SPARC]: Fix iommu_flush_iotlb end address
  [SPARC]: Mark smp init functions as cpuinit
  [SPARC]: Add missing rw can_lock macros
  [SPARC]: Setup cpu_possible_map
  [SPARC]: Add topology_init()

* 'rio.b19' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird:
  [PATCH] missing readb/readw in rio
  [PATCH] copy_to_user() from iomem is a bad thing
  [PATCH] forgotten swap of copyout() arguments
  [PATCH] handling rio MEMDUMP
  [PATCH] fix rio_copy_to_card() for OLDPCI case
  [PATCH] uses of ->Copy() in rioroute are bogus
  [PATCH] bogus order of copy_from_user() arguments
  [PATCH] rio ->Copy() expects the sourse as first argument
  [PATCH] trivial annotations in rio

* 'audit.b21' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current: (25 commits)
  [PATCH] make set_loginuid obey audit_enabled
  [PATCH] log more info for directory entry change events
  [PATCH] fix AUDIT_FILTER_PREPEND handling
  [PATCH] validate rule fields' types
  [PATCH] audit: path-based rules
  [PATCH] Audit of POSIX Message Queue Syscalls v.2
  [PATCH] fix se_sen audit filter
  [PATCH] deprecate AUDIT_POSSBILE
  [PATCH] inline more audit helpers
  [PATCH] proc_loginuid_write() uses simple_strtoul() on non-terminated array
  [PATCH] update of IPC audit record cleanup
  [PATCH] minor audit updates
  [PATCH] fix audit_krule_to_{rule,data} return values
  [PATCH] add filtering by ppid
  [PATCH] log ppid
  [PATCH] collect sid of those who send signals to auditd
  [PATCH] execve argument logging
  [PATCH] fix deadlocks in AUDIT_LIST/AUDIT_LIST_RULES
  [PATCH] audit_panic() is audit-internal
  [PATCH] inotify (5/5): update kernel documentation
  ...

Manual fixup of conflict in unclude/linux/inotify.h

tosa.c references mdelay(), but was missing linux/delay.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
  [S390] __FD_foo definitions.
  Switch to __s32 types in joystick.h instead of C99 types for consistency.
  Add <sys/types.h> to headers included for userspace in <linux/input.h>
  Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
  Remove struct fddi_statistics from user view in <linux/if_fddi.h>
  Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
  Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
  Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
  Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
  Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
  Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
  Use __uXX types in <linux/divert.h> for struct divert_blk et al.
  Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
  Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
  Use __uXX types in user-visible structures in <linux/nbd.h>
  Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
  Use __uXX types for S390 DASD volume label definitions which are user-visible
  S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
  Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
  Fix private integer types used in V4L2 ioctls.
  ...

Manually resolve conflict in include/linux/mtd/physmap.h

* git://git.infradead.org/~dwmw2/rbtree-2.6:
  [RBTREE] Switch rb_colour() et al to en_US spelling of 'color' for consistency
  Update UML kernel/physmem.c to use rb_parent() accessor macro
  [RBTREE] Update hrtimers to use rb_parent() accessor macro.
  [RBTREE] Add explicit alignment to sizeof(long) for struct rb_node.
  [RBTREE] Merge colour and parent fields of struct rb_node.
  [RBTREE] Remove dead code in rb_erase()
  [RBTREE] Update JFFS2 to use rb_parent() accessor macro.
  [RBTREE] Update eventpoll.c to use rb_parent() accessor macro.
  [RBTREE] Update key.c to use rb_parent() accessor macro.
  [RBTREE] Update ext3 to use rb_parent() accessor macro.
  [RBTREE] Change rbtree off-tree marking in I/O schedulers.
  [RBTREE] Add accessor macros for colour and parent fields of rb_node

* git://git.infradead.org/mtd-2.6: (199 commits)
  [MTD] NAND: Fix breakage all over the place
  [PATCH] NAND: fix remaining OOB length calculation
  [MTD] NAND Fixup NDFC merge brokeness
  [MTD NAND] S3C2410 driver cleanup
  [MTD NAND] s3c24x0 board: Fix clock handling, ensure proper initialisation.
  [JFFS2] Check CRC32 on dirent and data nodes each time they're read
  [JFFS2] When retiring nextblock, allocate a node_ref for the wasted space
  [JFFS2] Mark XATTR support as experimental, for now
  [JFFS2] Don't trust node headers before the CRC is checked.
  [MTD] Restore MTD_ROM and MTD_RAM types
  [MTD] assume mtd->writesize is 1 for NOR flashes
  [MTD NAND] Fix s3c2410 NAND driver so it at least _looks_ like it compiles
  [MTD] Prepare physmap for 64-bit-resources
  [JFFS2] Fix more breakage caused by janitorial meddling.
  [JFFS2] Remove stray __exit from jffs2_compressors_exit()
  [MTD] Allow alternate JFFS2 mount variant for root filesystem.
  [MTD] Disconnect struct mtd_info from ABI
  [MTD] replace MTD_RAM with MTD_GENERIC_TYPE
  [MTD] replace MTD_ROM with MTD_GENERIC_TYPE
  [MTD] remove a forgotten MTD_XIP
  ...

* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] PARPORT_SERIAL should depend on SERIAL_8250_PCI

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [MMC] Add (MMC) to entry in MAINTAINERS file
  [MMC] sdhci truncated pointer fix

* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
  [ARM] 3559/1: S3C2442: core and serial port
  [ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
  [ARM] 3558/1: SMDK24XX: LED platform devices
  [ARM] 3534/1: add spi support to lubbock platform
  [ARM] 3554/1: ARM: Fix dyntick locking
  [ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
  [ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
  [ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
  [ARM] 3550/1: OSIRIS: fix serial port map for 1:1
  [ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
  [ARM] 3335/1: Old-abi Thumb sys_syscall broken
  [ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
  [ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
  [ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
  [ARM] 3407/1: lpd7x: documetation update
  [ARM] 3406/1: lpd7x: compilation fix for smc91x
  [ARM] 3405/1: lpd7a40x: CPLD ssp driver
  [ARM] 3404/1: lpd7a40x: AMBA CLCD support
  [ARM] 3403/1: lpd7a40x: updated default configurations
  [ARM] 3402/1: lpd7a40x: serial driver bug fix
  ...

Patch from Deepak Saxena

This patch makes soft reboot work on the Versatile board. Thanks to
Catalin Marinas @ ARM for pointing out the proper way to do this.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Following problems are addressed:

- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
  is a relict of the abandoned support for interrupted
  erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations

Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Remove the remains of a broken merge.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch removes some now unnecessary global variables -
at91_master_clock, at91_serial_map, at91_console_port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Update s3c2410_defconfig to latest kernel with the
latest patches
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This final patch includes some general fixes.

1. Link in pm.o if CONFIG_PM is enabled.  [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds the core Power Management support for the AT91RM9200
processor.  It will support suspend-to-RAM and standby modes.

The suspend-to-RAM functionality is not 100% complete.  The code that
needs to be execute from the internal SRAM to restore the system is
outstanding.  For now we just fall through to Standby mode.

The AT91-specific at91_suspend_entering_slow_clock() function will
eventually be replaced by clk_must_disable() once that functionality is
added to mainline clock API.

Patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support for an additional 4 AT91RM9200-based boards:

1. Conitec ARM&EVA  [MACH_CARMEVA]
   (http://www.conitec.net/english/linuxboard.htm)

2. KwikByte KB920x  [MACH_KB9200]
   (http://kwikbyte.com/KB9202_description_new.htm)

3. Embest ATEB9200  [MACH_ATEB9200]
   (http://www.embedinfo.com/english/product/ATEB9200.asp)

4. Sperry-Sun KAFA board  [MACH_KAFA]
   (unknown)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>