- 14 Jan, 2006 28 commits
-
-
Mike Christie authored
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>: We cannot use page_address becuase some pages could be highmem. Instead, we can use sock_no_sendpage which does kmap for us. Signed-off-by: Alex Aizman <itn780@yahoo.com> Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
FUJITA Tomonori authored
Users can write to a page while we are sending it and making digest calculations. This ends up causing us to retry the command when a digest error is later reported. By using sock_no_sendpage when data digests are calculated we can avoid a lot of (not all but it helps) the retries becuase sock_no_sendpage is not zero copy. Signed-off-by: Alex Aizman <itn780@yahoo.com> Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
zhenyu.z.wang@intel.com authored
We should be taking the host_lock instead of the conn lock when checking host_busy. Signed-off-by: Alex Aizman <itn780@yahoo.com> Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
zhenyu.z.wang@intel.com authored
We need to check the ISCSI_FLAG_DATA_* flags. Signed-off-by: Alex Aizman <itn780@yahoo.com> Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
FUJITA Tomonori authored
Remove extra whitespaces. Signed-off-by: Alex Aizman <itn780@yahoo.com> Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Jes Sorensen authored
Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead of semaphores. Untested, but compiles and looks obviously correct. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
James Bottomley authored
Now that mptfc actually uses the transport class, it can't be built without it. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Moore, Eric authored
The fix is to write 'MPI_HIM_DIM' to the Host Interrupt Mask register, when enabling interrupts. Instead of the tilde of MPI_HIM_RIM. Apparently writing '1's to some of the reserved bits was causing all the bits to go to `1`, which effectly disabled all interrupts. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Moore, Eric authored
We will be mapping the RAID volumes in mptsas to a reserved channel that is one larger than the anticapated number of ports on the direct attached host adapter. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Moore, Eric authored
This updates mpi headers in fusion drivers to version 1.5.12. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Moore, Eric authored
The SAS RAID volumes are reported beyond the expected number of phys. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
When James Smart fixed the issue of the userspace scan atributes crashing the system with the FC transport class he added a patch to let the transport class check if the parent is valid for a given transport class. When adding support for the integrated raid of fusion sas devices we ran into a problem with that, as it didn't allow adding virtual raid volumes without the transport class knowing about it. So this patch adds a user_scan attribute instead, that takes over from scsi_scan_host_selected if the transport class sets it and thus lets the transport class control the user-initiated scanning. As this plugs the hole about user-initiated scanning the target_parent hook goes away and we rely on callers of the scanning routines to do something sensible. For SAS this meant I had to switch from a spinlock to a mutex to synchronize the topology linked lists, in FC they were completely unsynchronized which seems wrong. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Moore, Eric authored
Add software recognition for the new LSI Logic Fibre Channel controller. Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Michael Reed authored
Signed-off-by: Michael Reed <mdr@sgi.com> Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Jes Sorensen authored
Convert the SCSI transport class code to use a mutex rather than a semaphore. Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
James Bottomley authored
There was a use before initialisation of c->name Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
Convert kmalloc + memset to kzalloc or kcalloc in fusion. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
Adds hotplug support for SAS end devices. Unfortunately the fusion firmware doesn't generate similar events for expanders addition/removal so we can't support them yet. Eric has an idea about a clever scheme to find out about expander changes so that'll be added later on. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Salyzyn, Mark authored
The problem in dpt_i2o could be the pci config space accesses it triggers as it loads, dangerous to do if there is any I/O activity going on in the other driver (probable if a boot driver I guess). I approve this patch to dpt_i2o.c, and am applying it to the Adaptec branch of the driver. Thanks for the investigation Ryoji. --- In linux 2.6.15, data transfer does hang when both dpt_i2o and i2o_block drivers are loaded. It seems that location of pci_request_regions() are wrong. I moved it just behind pci_enable_device() like other drivers, and it becomes fine. Signed-off-by: Ryoji Kamei <kamei@miraclelinux.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Jack Hammer authored
To avoid the "sda: got wrong page" message, the ServeRAID driver should be setting flags indicating that the Mode Sense commands are not supported. Signed-off-by: Jack Hammer <jack_hammer@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Andreas Herrmann authored
Replaced zfcp adapter attributes with fc_host attributes: fc_topology by port_type, physical_wwpn by permanent_port_name. Make use of fc_host attribute supported_speeds. Removed zfcp adapter attribute physical_s_id. Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Andreas Herrmann authored
Added host stats, removed superfluous get_starget_ functions, removed some attributes from zfcp specific sysfs tree (e.g. scsi_host_no, scsi_lun, wwnn and d_id). Host stats are given for the physical adapter port not for the virtual adapter. Reset stats is implemented in the device driver. Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Maxim Shchetynin authored
Handle unsolicited adapter status that informs about loss of previous unsolicited status notification(s). Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com> Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Andreas Herrmann authored
Add fc_host attribute permanent_port_name which is used to show the port name of the primary port - the port that initially logged into the fabric. For a virtual port (registered via the primary port with FDISC command) it is useful to know not only its (virtual) port name but also the permanent port name. Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
split each ioctl handled in sr_audio_ioctl into a function of it's own. This cleans the code up nicely, and allows various places in sr_ioctl to call these helpers directly instead of going through the multiplexer. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Jens Axboe <axboe@suse.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just fine in the core code. There is a small behaviour change in that some check in sr's rw_intr are bypassed, but I consider the old behaviour a bug. Mike found this cleanup opportunity and provdided early patches, so all the credit goes to him, even if I redid the patches from scratch beause that was easier than forward-porting the old patches. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
We need to iterate over all children when removing and expander, else stale objects will be around after host removal. This fixes the oops Eric Moore saw when removing and reloading mptsas. Also don't try the scsi_remove_target call unless operating on an end device. The current unconditional call is harmless but confusing. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
- 12 Jan, 2006 12 commits
-
-
Petr Vandrovec authored
While trying to get SUSE's SLES9 working on system with more than 4GB we've noticed that SCSI layer happilly passes addresses over 4GB to the buslogic driver, which is quite a big problem as buslogic can generate only 32bit busmastering cycles. Fortunately in the current kernels this problem does not exist anymore as SCSI layer now assumes 4GB capable device by default, but it is still good idea to pass correct device structure to the SCSI layer. If nothing else, /sys/block/sda/device now points to /sys/devices/pci0000:00/0000:00:10.0/host0/... instead of /sys/devices/platform/host0/... like it did in the past. Change does nothing for ISA based BusLogic adapters, they'll still end under platform (and they are probably broken for long time as I do not see anything forcing ISA 16MB limit for them). Signed-off-by: Petr Vandrovec <petr@vmware.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
James Bottomley authored
This takes us past the old 1.x version of the SCSI driver and the 2.x version of the aic website version to reflect the full incorporation of both branches. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Hannes Reinecke authored
Update sequencer code to Adaptec version 2.0.12-6.3.9. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Hannes Reinecke authored
This patch coalesces inb/outb calls to the approriate word or long form. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Hannes Reinecke authored
Use struct map_node instead of separate variables. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Hannes Reinecke authored
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Chuck Ebbert authored
SCSI-1 CD drives can't do MRW or be opened for writing, so mask off those capabilities. Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com> Acked-by: Jens Axboe <axboe@suse.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Mark Haverkamp authored
Received From Mark Salyzyn. Move the README from the driver directory to the Documentation directory. Updated the documentation, added descriptions for cards that were missing. Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Mark Haverkamp authored
Received From Mark Salyzyn. The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC) perform better (about 10% better read performance, write performance neutral) with current Firmware if the OS limits the number of scatter gather elements to 17 per request. Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Mark Haverkamp authored
Received from Mark Salyzyn. Provide more accurate adapter information. Allows the Adapter Firmware to override the Adapter product information. Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Mark Haverkamp authored
Received from Mark Salyzyn. If the adapter has not instructed us otherwise that it can handle a 'large' FIB, then it can handle at most a 2KB FIB. Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-
Christoph Hellwig authored
We need to clear the backpointer on rphy removal, else we'll run into problems with host removal after a device has been hot unplugged. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
-