We we set the too early, they may still be in place and possibly get called
even though the array didn't get set up properly.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When a request crosses a boundary between devices, it needs to be split.
But where we should calculate the amount of the request before the boundary
to find the split-point, we care currently calculating the amount that is
*after* the boundary !!!
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Replace one memcpy() call with overlapping source and dest arguments with
one call to memmove(), to avoid data corruption.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Actually remove elf.h in the tree.  The previous patch, due to a quilt
bug/misuse, left it in the tree as a 0-length file, preventing the build to
see it as missing and to generate a symlink in its place.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Additional i8xx_tco device support.

Cc: David Hardeman <david@2gen.com>
Cc: <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Kernel 2.6 has an ide proc destroy error. Run #modprobe ide-core and
#rmmod ide-core, then kernel will dump stack information like below.

**********Log******************
Badness in remove_proc_entry at fs/proc/generic.c:693

Call Trace:
 [<a0000001000117e0>] show_stack+0x80/0xa0
                                sp=3De0000003e05dfbe0 =
bsp=3De0000003e05d0ea8
 [<a0000001000120b0>] dump_stack+0x30/0x60
                                sp=3De0000003e05dfdb0 =
bsp=3De0000003e05d0e90
 [<a000000100183090>] remove_proc_entry+0x530/0x540
                                sp=3De0000003e05dfdb0 =
bsp=3De0000003e05d0e20
 [<a000000221cbd280>] proc_ide_destroy+0x120/0x140 [ide_core]
                                sp=3De0000003e05dfdc0 =
bsp=3De0000003e05d0df0
 [<a000000221ca65f0>] cleanup_module+0x50/0xa0 [ide_core]
                                sp=3De0000003e05dfdc0 =
bsp=3De0000003e05d0dd0
 [<a0000001000a9e10>] sys_delete_module+0x390/0x580
                                sp=3De0000003e05dfdc0 =
bsp=3De0000003e05d0d50
 [<a00000010000af40>] ia64_ret_from_syscall+0x0/0x20
                                sp=3De0000003e05dfe30 =
bsp=3De0000003e05d0d50
 [<a000000000010640>] _stext+0xffffffff00010640/0x400
                                sp=3De0000003e05e0000 =
bsp=3De0000003e05d0d50
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

VmallocTotal: 34359738367 kB
VmallocUsed:    266288 kB
VmallocChunk: 18014366299193295 kB
is unsettling - x86_64 and some other architectures keep a separate address
range for modules in vmalloc's vmlist, which /proc/meminfo should pass over.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

move serio port's id attributes into separate subdirectory:
       ..devices/serioX/id_type  -> ..devices/serioX/id/type
       ..devices/serioX/id_proto -> ..devices/serioX/id/proto
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

serport - avoid calling serio_interrupt or serio_write_wakeup on unregistered
port.  Also fix memory leak which could happen if serport was left unused by
moving serio allocation down to serport_ldisc_read.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

ALPS needs to be reset for detection to work reliably when reconnecting.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make the alps printk output look consistent.

Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

serio - do not attempt to immediately disconnect port if resume failed, let
kseriod take care of it.  Otherwise we may attempt to unregister associated
input devices which will generate hotplug events which are not handled well
during swsusp.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This is a tiny patch that fixes bttv-cards.c so that Leadtek WinFast VC100
XP video capture cards work.  I've been advised to post it here after
having already posted it to the v4l mailing list.
Acked-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

ioctl_by_bdev may only be used INSIDE the kernel.  If the "arg" argument
refers to memory that is accessed by put_user/get_user in the ioctl
function, the memory needs to be in the kernel address space (that's the
set_fs(KERNEL_DS) doing in the ioctl_by_bdev).  This works on i386 because
even with set_fs(KERNEL_DS) the user space memory is still accessible with
put_user/get_user.  That is not true for s390.  In short the ioctl
implementation of the pktcdvd device driver is horribly broken.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[Patch] Fix raw device ioctl pass-through

Raw character devices are supposed to pass ioctls through to the block
devices they are bound to.  Unfortunately, they are using the wrong
function for this: ioctl_by_bdev(), instead of blkdev_ioctl().

ioctl_by_bdev() performs a set_fs(KERNEL_DS) before calling the ioctl,
redirecting the user-space buffer access to the kernel address space.
This is, needless to say, a bad thing.

This was noticed first on s390, where raw IO was non-functioning.  The
s390 driver config does not actually allow raw IO to be enabled, which
was the first part of the problem.  Secondly, the s390 kernel address
space is distinct from user, causing legal raw ioctls to fail.  I've
reproduced this on a kernel built with 4G:4G split on x86, which fails
in the same way (-EFAULT if the address does not exist kernel-side;
returns success without actually populating the user buffer if it does.)

The patch below fixes both the config and address-space problems.  It's
based closely on a patch by Jan Glauber <jang@de.ibm.com>, which has
been tested on s390 at IBM.  I've tested it on x86 4G:4G (split address
space) and x86_64 (common address space).

Kernel-address-space access has been assigned CAN-2005-1264.
Signed-off-by: Stephen Tweedie <sct@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

As reported by Paul Starzetz <ihaquer@isec.pl>

Reference: CAN-2005-1263
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Mainline kernels don't have VECTORS_HIGH nor COPYPAGE_MINICACHE yet.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Version 2 of the 3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 is not
supported by the prism54 project.  To stop confusion, the kernel
documentation should state so as 3com made a good job hiding the version.
Signed-off-by: Andrew Morton <akpm@osdl.org>

diff -puN drivers/net/wireless/Kconfig~wireless-3crwe154g72-kconfig-help-fix drivers/net/wireless/Kconfig

This patch fixes a typo in tulip driver in 2.6.12-rc3.

Fix IBM EMAC driver ioctl bug.

I found IBM EMAC driver bug.
So mii-tool command print wrong status.

  # mii-tool
  eth0: 10 Mbit, half duplex, no link
  eth1: 10 Mbit, half duplex, no link

I can get correct status on fixed kernel.

  # mii-tool
  eth0: negotiated 100baseTx-FD, link okZZ
  eth1: negotiated 100baseTx-FD, link ok

Hiroaki Fuse

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> for CELF

	NET_WIRELESS is only a subset of the stuff in drivers/net/wireless;
NET_RADIO is what covers all of them.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>

Patch from Ben Dooks

Fix the setting of hdiv when set to divide-by-2. Thanks to
Jeonghoon Yoon for pointing this out.
Change name of the NAND device to "s3c2440-nand" as it
is not similar enough to the "s3c2410-nand" device.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

S3C2440 UPLL is the same as the S3C2410 UPLL, it is only the
MPLL which has an extra multiplication factor of 2 in the
multiplier.

Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add the register definitions for the s3c2440 NAND controller
to the s3c2410 NAND register definitions

Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Not all ARMv6 processors implement the TLS register.

Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Sascha Hauer

This patch adds the defines for the i.MX PWM controller

Signed-off-by: Steven Scholz
Signed-off-by: Sascha Hauer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add cache flushing support for aliased V6 caches to
flush_dcache_page.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Remove needless page table walking for v6 page operations.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Move the locking for copy_user_page() and clear_user_page() into
the implementations which require locking.  For simple memcpy/
memset based implementations, the locking is extra overhead which
is not necessary, and prevents preemption occuring.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Add uart_insert_char(), which handles inserting characters into the
flip buffer.  This helper function handles the correct semantics
for handling overrun in addition to inserting normal characters.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Add pmd_off() and pmd_off_k() to obtain the pmd pointer for a
virtual address, and use them throughout the mm initialisation.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>

Updates to the wbsd driver.
                                                                                
* Fix to handle DAT3 card detection.
* Fixed bug which could cause large writes to stall in FIFO mode.
* Plug 'n Play support. In most cases you need ACPI PNP for this to work.
* Uses generic DMA API (ISA dependency removed).

This fixes some x86_64 bugs -

- maybe_map returns -1 on error instead of 0, which is interpreted as
  physical address 0

- removed an include of ipc.h, which isn't needed

- fixed the calculation of signal frame location

- the signal delivery code is now immune to the stack expansion check

- added a missing include
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

tt-mode closes switch_pipes in exit_thread_tt and kills processes in
switch_to_tt, if the exit_state is EXIT_DEAD or EXIT_ZOMBIE.

In very rare cases the exiting process can be scheduled out after having set
exit_state and closed switch_pipes (from release_task it calls proc_pid_flush,
which might sleep).  If this process is to be restarted, UML failes in
switch_to_tt with:

   write of switch_pipe failed, err = 9

We fix this by closing switch_pipes not in exit_thread_tt, but later in
release_thread_tt.  Additionally, we set switch_pipe[0] = 0 after closing.
switch_to_tt must not kill "from" process depending on its exit_state, but
must kill it after release_thread was processed only, so it examines
switch_pipe[0] for its decision.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>