Merge branch 'upstream-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream

Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY.  This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool.  Any PHYs that are present can be accessed via the MII
ioctl()s.

This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Mantra: don't use flush_scheduled_work with RTNL held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Your usual dont-flush_scheduled_work-with-RTNL-held stuff.

It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.

rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Cobalt: Fix UART I/O type
  [MIPS] Fixup copy_from_user_inatomic
  [MIPS] Fix struct sigcontext for N32 userland
  [MIPS] Make some __setup functions static
  [MIPS] Declare highstart_pfn, highend_pfn only if CONFIG_HIGHMEM=y
  [MIPS] Allow selection of KGDB only on platforms where it's supported.

The Cobalt UART is actually connected to memory resource area.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

From the 01408c49 log message:

The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source
address is not immediately available the copy fails *and* *zeros* *the*
*destination*.

This is a problem because a concurrent read (which admittedly is an odd
thing to do) might see zeros rather that was there before the write, or
what was there after, or some mixture of the two (any of these being a
reasonable thing to see).

If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't
cause an error.

The first copying does not need to zero any uncopied bytes, and doing
so causes the problem.  It uses copy_from_user_atomic rather than
copy_from_user so the simple expedient is to change copy_from_user_atomic
to *not* zero out bytes on failure.

< --- end cite --- >

This patch finally implements at least a not so pretty solution by
duplicating the relevant part of __copy_user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The kernel use 64-bit for sc_regs[0], and both N32/N64 userland
expects it was 64-bit.  But size of 'long' on N32 is actually 32-bit.
So this definition make some confusion.  Use __u32 and __u64 for
N32/N64 sigcontext to get rid of this confusion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes some sparse warnings. ("warning: symbol 'foo' was not
declared. Should it be static?")
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Due to type confusion, when an nfsacl verison 2 'ACCESS' request
finishes and tries to clean up, it calls fh_put on entiredly the
wrong thing and this can cause an oops.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The broadcast functionality is only necessary when a local APIC is
available. Make the config switch depend on X86_LOCAL_APIC. This
resolves the mach-voyager breakage introduced by the tick managament
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

powerpc gets:

init/main.c: In function `do_basic_setup':
init/main.c:714: warning: implicit declaration of function `init_irq_proc'

but we cannot include linux/irq.h in generic code.

Fix it by moving the declaration into linux/interrupt.h instead.

And make sure all code that defines init_irq_proc() is including
linux/interrupt.h.

And nuke an ifdef-in-C

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A user-specified get_nlinks may depend on other inode attributes.

Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The BUG_ON() in tick_nohz_stop_sched_tick() triggers on some boxen.
Remove the BUG_ON and print information about the pending softirq
to allow better debugging of the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When a CPU is needed for RCU the tick has to continue even when it was
stopped before.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] machzwd warning fix

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Update defconfigs
  [MIPS] Support for several more SNI RM models.
  [MIPS] Include <asm/bugs> to for declaration of check_bugs32.
  [MIPS] Add external declaration of pagetable_init() to pgalloc.h
  [MIPS] Make kernel_thread_helper() static
  [MIPS] Make __declare_dbe_table static and avoid it getting optimized away
  [MIPS] Use MIPS R2 instructions for bitops.
  [MIPS] signals: Share even more code.
  [MIPS] Fix CONFIG_MIPS32_N32=y CONFIG_MIPS32_O32=n build
  [MIPS] Iomap implementation.
  [MIPS] <asm/compat-signal.h> needs to include <asm/uaccess.h>.
  [MIPS] IP27: Fix warning.
  [MIPS] Fix sigset_t endianess swapping issues in 32-bit compat code.

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon/vt1211: Add probing of alternate config index port
  hwmon/f71805f: Fix a race condition
  hwmon/abituguru: Fix unchecked return status
  hwmon: New driver for the Analog Devices ADM1029
  hwmon/w83627ehf: Add support for the W83627DHG chip
  hwmon: Use subsys_initcall
  hwmon/lm70: Make lm70_remove a __devexit function
  hwmon: Cleanup a bogus legacy comment
  hwmon: Simplify the locking model of two drivers
  hwmon: Drop unused mutexes in two drivers
  hwmon/it87: Add PWM base frequency control

* git://git.infradead.org/mtd-2.6: (49 commits)
  [MTD] [NAND] S3C2412 fix hw ecc
  [MTD] [NAND] Work around false compiler warning in CAFÉ driver
  [JFFS2] printk warning fixes
  [MTD] [MAPS] ichxrom warning fix
  [MTD] [MAPS] amd76xrom warning fix
  [MTD] [MAPS] esb2rom warning fixes
  [MTD] [MAPS] ck804xrom warning fix
  [MTD] [MAPS] netsc520 warning fix
  [MTD] [MAPS] sc520cdp warning fix
  [MTD] [ONENAND] onenand_base warning fix
  [MTD] [NAND] eXcite nand flash driver
  [MTD] Improve heuristic for detecting wrong-endian RedBoot partition table
  [MTD] Fix RedBoot partition parsing regression harder.
  [MTD] [NAND] S3C2410: Hardware ECC correction code
  [JFFS2] Use MTD_OOB_AUTO to automatically place cleanmarker on NAND
  [MTD] Clarify OOB-operation interface comments
  [MTD] remove unused ecctype,eccsize fields from struct mtd_info
  [MTD] [NOR] Intel: remove ugly PROGREGION macros
  [MTD] [NOR] STAA: use writesize instead off eccsize to represent ECC block
  [MTD] OneNAND: Invalidate bufferRAM after erase
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: implement optional loose read cache
  9p: Use kthread_stop instead of sending a SIGKILL.

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
  [SCSI] SCSI core: better initialization for sdev->scsi_level
  [SCSI] scsi_proc.c: display sdev->scsi_level correctly
  [SCSI] megaraid_sas: update version and author info
  [SCSI] megaraid_sas: return sync cache call with success
  [SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
  [SCSI] megaraid_sas: add bios_param in scsi_host_template
  [SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
  [SCSI] scsi_transport.h should include scsi_device.h
  [SCSI] aic79xx: remove extra newline from info message
  [SCSI] scsi_scan.c: handle bad inquiry responses
  [SCSI] aic94xx: tie driver to the major number of the sequencer firmware
  [SCSI] lpfc: add PCI error recovery support
  [SCSI] megaraid: pci_module_init to pci_register_driver
  [SCSI] tgt: fix the user/kernel ring buffer interface
  [SCSI] sgiwd93: interfacing to wd33c93
  [SCSI] wd33c93: Fast SCSI with WD33C93B

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
  Input: remove obsolete setup parameters from input drivers
  Input: HIL - fix improper call to release_region()
  Input: hid-lgff - treat devices as joysticks unless told otherwise
  Input: HID - add support for Logitech Formula Force EX
  Input: gpio-keys - switch to common GPIO API
  Input: do not lock device when showing name, phys and uniq
  Input: i8042 - let serio bus suspend ports
  Input: psmouse - properly reset mouse on shutdown/suspend

* 'audit.b37' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] AUDIT_FD_PAIR
  [PATCH] audit config lockdown
  [PATCH] minor update to rule add/delete messages (ver 2)

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
  Documentation/kernel-docs.txt update.
  arch/cris: typo in KERN_INFO
  Storage class should be before const qualifier
  kernel/printk.c: comment fix
  update I/O sched Kconfig help texts - CFQ is now default, not AS.
  Remove duplicate listing of Cris arch from README
  kbuild: more doc. cleanups
  doc: make doc. for maxcpus= more visible
  drivers/net/eexpress.c: remove duplicate comment
  add a help text for BLK_DEV_GENERIC
  correct a dead URL in the IP_MULTICAST help text
  fix the BAYCOM_SER_HDX help text
  fix SCSI_SCAN_ASYNC help text
  trivial documentation patch for platform.txt
  Fix typos concerning hierarchy
  Fix comment typo "spin_lock_irqrestore".
  Fix misspellings of "agressive".
  drivers/scsi/a100u2w.c: trivial typo patch
  Correct trivial typo in log2.h.
  Remove useless FIND_FIRST_BIT() macro from cardbus.c.
  ...

* 'kill-jffs' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  Remove JFFS (version 1), as scheduled.

* 'acpi' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] libata: wrong sizeof for BUFFER
  [PATCH] libata: change order of _SDD/_GTF execution (resend #3)
  [PATCH] libata: ACPI _SDD support
  [PATCH] libata: ACPI and _GTF support

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (51 commits)
  sk98lin: mark deprecated in Kconfig
  Hostess SV-11 depends on INET
  Fix link autonegotiation timer.
  sk98lin: planned removal
  B44: increase wait loop
  b44: replace define
  e1000: allow ethtool to see link status when down
  e1000: remove obsolete custom pci_save_state code
  e1000: fix shared interrupt warning message
  atm: Use ARRAY_SIZE macro when appropriate
  bugfixes and new hardware support for arcnet driver
  pcnet32 NAPI no longer experimental
  MAINTAINER
  macb: Remove inappropriate spinlocks around mii calls
  Convert meth to netdev_priv
  sky2: v1.13
  sky2: receive error handling improvements
  sky2: transmit timeout
  sky2: flow control negotiation for Yukon-FE
  sky2: no need to reset pause bits on shutdown
  ...

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
  [ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
  [ARM] 4140/1: AACI stability add ac97 timeout and retries
  [ARM] 4139/1: AACI record support
  [ARM] 4138/1: AACI: multiple channel support for IRQ handling
  [ARM] 4211/1: Provide a defconfig for ns9xxx
  [ARM] 4210/1: base for new machine type "NetSilicon NS9360"
  [ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
  [ARM] 4221/1: S3C2443: DMA support
  [ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
  [ARM] 4219/1: S3C2443: DMA source definitions
  [ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
  [ARM] 4217/1: S3C24XX: remove the dma channel show at startup
  [ARM] 4090/2: avoid clash between PXA and SA1111 defines
  [ARM] 4216/1: add .gitignore entries for ARM specific files
  [ARM] 4214/2: S3C2410: Add Armzone QT2410
  [ARM] 4215/1: s3c2410 usb device:  per-platform vbus_draw
  [ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
  [ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
  [ARM] 4137/1: Add kexec support
  [ARM] 4201/1: SMP barriers pair needed for the secondary boot process
  ...

Fix up conflict due to typedef removal in sound/arm/aaci.h

* 'for-linus' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: fix another deadlock in nodemgr
  ieee1394: cycle timer read extension for raw1394

* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (34 commits)
  [POWERPC] 86xx: Cleaned up platform dts files
  [POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards
  [POWERPC] 85xx: Cleaning up machine probing
  [POWERPC] QE: clean up ucc_slow.c and ucc_fast.c
  [POWERPC] 85xx: Cleaned up platform dts files
  [POWERPC] 83xx: Renamed MPC8323 MDS dts and defconfig to match other boards
  [POWERPC] 83xx: Updated and renamed MPC8360PB to MPC836x MDS
  [POWERPC] 83xx: Use of_platform_bus_probe to setup QE devices
  [POWERPC] 83xx: use default value of loops_per_jiffy
  [POWERPC] 83xx: Remove obsolete setting of ROOT_DEV.
  [POWERPC] 83xx: Cleaning up machine probing and board initcalls
  [POWERPC] Dispose irq mapping when done in mpc52xx_serial.c
  [POWERPC] 86xx: Add missing of_node_put() in mpc86xx_hpcn_init_irq().
  [POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms.
  [POWERPC] pseries: Enabling auto poweron after power is restored.
  [POWERPC] use winbond libata instead of ide driver for pseries CD drives
  [POWERPC] powerpc: remove references to the obsolete linux,platform property
  [POWERPC] add of_get_mac_address and update fsl_soc.c to use it
  [POWERPC] 83xx: Cleaned up 83xx platform dts files
  [POWERPC] Fix bug with early ioremap and 64k pages
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (30 commits)
  ide: make ide_hwif_t.ide_dma_host_on void (v2)
  ide: make ide_hwif_t.ide_dma_{host_off,off_quietly} void (v2)
  ide: add ide_set_dma() helper (v2)
  sgiioc4: fix sgiioc4_ide_dma_check() to enable/disable DMA properly
  ide: disable DMA in ->ide_dma_check for "no IORDY" case (v2)
  ide: convert ide_hwif_t.mmio into flag (v2)
  ide: use PIO/MMIO operations directly where possible (v2)
  ide: add ide_use_fast_pio() helper (v3)
  ide: unexport ide_set_xfer_rate() (v2)
  ide: remove ide_drive_t.usage
  ide: remove ide_pci_device_t tables with only one entry
  ide: remove write-only ide_hwif_t.no_dsc flag
  ide: remove write-only ide_pio_data_t.blacklisted
  sis5513: sis5513_config_xfer_rate() cleanup
  piix: cleanup
  svwks: small cleanup
  cs5530: small cleanup
  hpt366: remove redundant check from init_dma_hpt366()
  trm290: remove redundant CONFIG_BLK_DEV_IDEDMA #ifdef-s
  au1xxx-ide: remove dead code
  ...

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/core: Set static rate in ib_init_ah_from_path()
  IB/ipath: Make ipath_map_sg() static
  IB/core: Fix sparse warnings about shadowed declarations
  RDMA/cma: Add multicast communication support
  IB/sa: Track multicast join/leave requests
  IPoIB: CM error handling thinko fix
  RDMA/cxgb3: Remove Open Grid Computing copyrights in iw_cxgb3 driver
  RDMA/cxgb3: Fail posts synchronously when in TERMINATE state
  RDMA/iwcm: iw_cm_id destruction race fixes
  IB/ehca: Change query_port() to return LINK_UP instead UNKNOWN
  IB/ehca: Allow en/disabling scaling code via module parameter
  IB/ehca: Fix race condition/locking issues in scaling code
  IB/ehca: Rework irq handler
  IPoIB: Only allow root to change between datagram and connected mode
  IB/mthca: Fix allocation of ICM chunks in coherent memory
  IB/mthca: Allow the QP state transition RESET->RESET

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
  PCI: Make PCI device numa-node attribute visible in sysfs
  PCI: add systems for automatic breadth-first device sorting
  PCI: PCI devices get assigned redundant IRQs
  PCI: Make CARDBUS_MEM_SIZE and CARDBUS_IO_SIZE boot options
  PCI: pci.txt fix __devexit() usage
  PCI/sysfs/kobject kernel-doc fixes