- 14 Jan, 2006 8 commits
-
-
Jack Hammer authored
To avoid the "sda: got wrong page" message, the ServeRAID driver should be setting flags indicating that the Mode Sense commands are not supported. Signed-off-by:
Jack Hammer <jack_hammer@adaptec.com> Signed-off-by:
James Bottomley <James.Bottomley@SteelEye.com>
-
Andreas Herrmann authored
Replaced zfcp adapter attributes with fc_host attributes: fc_topology by port_type, physical_wwpn by permanent_port_name. Make use of fc_host attribute supported_speeds. Removed zfcp adapter attribute physical_s_id. Signed-off-by:
Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by:
-
Andreas Herrmann authored
Added host stats, removed superfluous get_starget_ functions, removed some attributes from zfcp specific sysfs tree (e.g. scsi_host_no, scsi_lun, wwnn and d_id). Host stats are given for the physical adapter port not for the virtual adapter. Reset stats is implemented in the device driver. Signed-off-by:
-
Maxim Shchetynin authored
Handle unsolicited adapter status that informs about loss of previous unsolicited status notification(s). Signed-off-by:
Maxim Shchetynin <maxim@de.ibm.com> Signed-off-by:
-
Andreas Herrmann authored
Add fc_host attribute permanent_port_name which is used to show the port name of the primary port - the port that initially logged into the fabric. For a virtual port (registered via the primary port with FDISC command) it is useful to know not only its (virtual) port name but also the permanent port name. Signed-off-by:
-
Christoph Hellwig authored
split each ioctl handled in sr_audio_ioctl into a function of it's own. This cleans the code up nicely, and allows various places in sr_ioctl to call these helpers directly instead of going through the multiplexer. Signed-off-by:
Christoph Hellwig <hch@lst.de> Acked-by:
Jens Axboe <axboe@suse.de> Signed-off-by:
-
Christoph Hellwig authored
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just fine in the core code. There is a small behaviour change in that some check in sr's rw_intr are bypassed, but I consider the old behaviour a bug. Mike found this cleanup opportunity and provdided early patches, so all the credit goes to him, even if I redid the patches from scratch beause that was easier than forward-porting the old patches. Signed-off-by:
-
Christoph Hellwig authored
We need to iterate over all children when removing and expander, else stale objects will be around after host removal. This fixes the oops Eric Moore saw when removing and reloading mptsas. Also don't try the scsi_remove_target call unless operating on an end device. The current unconditional call is harmless but confusing. Signed-off-by:
-
- 12 Jan, 2006 32 commits
-
-
Petr Vandrovec authored
While trying to get SUSE's SLES9 working on system with more than 4GB we've noticed that SCSI layer happilly passes addresses over 4GB to the buslogic driver, which is quite a big problem as buslogic can generate only 32bit busmastering cycles. Fortunately in the current kernels this problem does not exist anymore as SCSI layer now assumes 4GB capable device by default, but it is still good idea to pass correct device structure to the SCSI layer. If nothing else, /sys/block/sda/device now points to /sys/devices/pci0000:00/0000:00:10.0/host0/... instead of /sys/devices/platform/host0/... like it did in the past. Change does nothing for ISA based BusLogic adapters, they'll still end under platform (and they are probably broken for long time as I do not see anything forcing ISA 16MB limit for them). Signed-off-by:
Petr Vandrovec <petr@vmware.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
James Bottomley authored
This takes us past the old 1.x version of the SCSI driver and the 2.x version of the aic website version to reflect the full incorporation of both branches. Signed-off-by: -
Hannes Reinecke authored
Update sequencer code to Adaptec version 2.0.12-6.3.9. Signed-off-by: -
Hannes Reinecke authored
This patch coalesces inb/outb calls to the approriate word or long form. Signed-off-by: -
Hannes Reinecke authored
Use struct map_node instead of separate variables. Signed-off-by: -
Hannes Reinecke authored
Signed-off-by: -
Chuck Ebbert authored
SCSI-1 CD drives can't do MRW or be opened for writing, so mask off those capabilities. Signed-off-by:
Chuck Ebbert <76306.1226@compuserve.com> Acked-by:
-
Mark Haverkamp authored
Received From Mark Salyzyn. Move the README from the driver directory to the Documentation directory. Updated the documentation, added descriptions for cards that were missing. Signed-off-by:
Mark Haverkamp <markh@osdl.org> Signed-off-by:
-
Mark Haverkamp authored
Received From Mark Salyzyn. The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC) perform better (about 10% better read performance, write performance neutral) with current Firmware if the OS limits the number of scatter gather elements to 17 per request. Signed-off-by:
-
Mark Haverkamp authored
Received from Mark Salyzyn. Provide more accurate adapter information. Allows the Adapter Firmware to override the Adapter product information. Signed-off-by:
-
Mark Haverkamp authored
Received from Mark Salyzyn. If the adapter has not instructed us otherwise that it can handle a 'large' FIB, then it can handle at most a 2KB FIB. Signed-off-by:
-
Christoph Hellwig authored
We need to clear the backpointer on rphy removal, else we'll run into problems with host removal after a device has been hot unplugged. Signed-off-by:
-
Arjan van de Ven authored
the scsi layer is using semaphores in a mutex way, this patch converts these into using mutexes instead Signed-off-by:
Arjan van de Ven <arjan@infradead.org> Signed-off-by:
-
James Bottomley authored
The driver is doing a rather stupid mod_timer allegedly to "give request sense more time to complete". This is illegal and pointless, so just eliminate it. Also eliminate all the other uses of struct timer_list in the driver, which are mostly bogus. Signed-off-by: -
Andrew Vasquez authored
Original From: Adrian Bunk Here's a composite patch with Adrian's original additions and help-text with the new Kconfig variable SCSI_QLA_FC. Signed-off-by: -
Adrian Bunk authored
Signed-off-by:
Adrian Bunk <bunk@stusta.de> Acked-by:
James Smart <James.Smart@Emulex.Com> Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
-
Moore, Eric authored
Adding defines for RAID10 and RAID50 levels, in preparation of adding RAID Transport support in the mpt fusion drivers. (BTW: IME is RAID10, and IM is RAID1). Signed-off-by:
Eric Moore <Eric.Moore@lsil.com> Signed-off-by:
-
Linus Torvalds authored
-
Vivek Goyal authored
o This fix was posted for i386 long back. Posting it for x86_64. http://marc.theaimsgroup.com/?l=linux-kernel&m=110380103229830&w=2 o This patch fixes the problem of secondary cpus boot up. This situation is faced when kernel is built for default locations like 16MB and onwards. In this configuration, only primary cpu (BP) comes and secondary cpus don't boot. o Problem occurs because in trampoline code, lgdt is not able to load the GDT as it happens to be situated beyond 16MB. This is due to the fact that cpu is still in real mode and default operand size is 16bit. o This patch uses lgdtl instead of lgdt to force operand size to 32 instead of 16. Signed-off-by:
Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by:
Andi Kleen <ak@suse.de> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Andi Kleen authored
Handling common prefixes is tricky. Signed-off-by:
-
Jan Beulich authored
... reducing the amount of changes Xen has to do. Signed-Off-By:
Jan Beulich <jbeulich@novell.com> Signed-off-by:
-
Jan Beulich authored
The explicit and implicit calls to setup_early_printk() were passing inconsistent arguments. Signed-Off-By:
-
Andi Kleen authored
It has no business being elsewhere and x86-64 doesn't need/want it. Signed-off-by:
-
Andi Kleen authored
Previously they would be only allocated before the kernel text at 1MB. This limited the maximum supported memory to 128GB. Now allow the e820 allocator to put them everywhere. Try to put them beyond any DMA zones to avoid filling them up. This should free some GFP_DMA memory compared to earlier kernels. Signed-off-by:
-
Andi Kleen authored
hard_smp_processor_id would return the local APIC id instead of the Linux processor id. On big systems they are often not identical. safe_smp_processor_id is just a wrapper around it that does the necessary conversions. Signed-off-by:
-
Andi Kleen authored
Remove support for obsolete hardware and cleanup. - Remove checks for non integrated APICs - Replace apic_write_around with apic_write. - Remove apic_read_around - Remove APIC version reads used by old workarounds - Remove old workaround for Simics - Fix indentation Signed-off-by:
-
Jan Beulich authored
When building in a separate objtree, file names produced by BUG() & Co. can get fairly long; printing only the first 50 characters may thus result in (almost) no useful information. The following change makes it so that rather the last 50 characters of the filename get printed. Signed-Off-By:
-
Jan Beulich authored
Especially under Xen, where the console cannot be adjusted to more than 25 lines, it is fairly important that the information displayed during a panic is as compact as possible. Below adjustments work towards that. Signed-Off-By:
-
Jan Beulich authored
Due to a broken condition, the body of the loop that is intended to wait for the Update-In-Progress bit to get set and then cleared again was never entered; in fact, the entire loop was optimized out by the compiler. Here is a change to fix the condition (and to also move the initialization of locals out of the spin lock protected region). Signed-Off-By:
-
Andi Kleen authored
It was only needed for APM Pointed out by Jan Beulich Cc: jbeulich@novell.com Signed-off-by:
-
Andi Kleen authored
X86_FEATURE_K8_C was a synthetic Linux CPUID flag that was used for some code optimizations in Opteron C stepping or later. But support for pre C stepping optimizations has been removed, so this isn't needed anymore. Signed-off-by:
-
