Compiling with '-Wswitch-enum' I noticed following:

  CC      drivers/ide/ide-proc.o
drivers/ide/ide-proc.c: In function ‘proc_ide_read_imodel’:
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_etrax100’ not handled in switch
drivers/ide/ide-proc.c:54: warning: enumeration value ‘ide_acorn’ not handled in switch

How about the following patch?
Signed-off-by: Mika Kukkonen <mikukkon@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It turns out from customer reports to Red Hat and some PCI dumps that the
MegaIDE in RAID mode doesn't provide the drive tuning data that the
serverworks driver expects but sometimes does provide something that
fools the code.

For the RAID class case skip the oem setup and don't trust the BIOS data.
We then tune from scratch and this sorts it out. (This has been confirmed
on an afflicted IBM blade)

[libata serverworks.c never trusts the BIOS in the first place so is
accidentally immune]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.

From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [RTNETLINK]: Remove remains of wireless extensions over rtnetlink
  [RTNETLINK]: Allow changing of subsets of netdevice flags in rtnl_setlink
  [AF_RXRPC]: Make call state names available if CONFIG_PROC_FS=n
  [AF_RXRPC]: AF_RXRPC depends on IPv4
  [IPSEC]: Fix warnings with casting int to pointer

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
  USB: Add support for Olimex arm-usb-ocd JTAG interface serial port
  USB: Add support for Sierra Wireless Aircard 595U
  USB: ldusb bugfix
  USB: ftdi_sio: Add USB Product Id for OpenDCC
  USB: fix ratelimit call semantics
  USB: handle errors in power/level attribute
  USB: make the autosuspend workqueue thread freezable
  USB: Fix USB OHCI Subvendor for Toshiba Portege 4000
  USB: usblp: Use correct DMA address in case of probe error
  USB: Fix debug output of ark3116
  USB: Onetouch - switch to using input_dev->dev.parent
  USB: don't try to kzalloc 0 bytes
  USB: remove short initial timeout for device descriptor fetch
  USB: Deref URB after usbmon is done with it
  USB: Remove duplicate IDs from option card driver
  USB: auerswald: fix file release handler
  USB: fsl_usb2_udc: Fix UMTI_WIDE support and a compile warning
  USB: set the correct Interrupt interval in usb_bulk_msg
  USB: New device PID for ftdi_sio driver
  USB: remove unneeded WARN_ON
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: ads7846 - SPI_CPHA mode bugfix
  Input: ads7846 - document that it handles tsc2046 too
  Input: input-polldev - add module info
  Input: ucb1x00-ts - remove commented out code
  Input: ucb1400_ts - use sched_setscheduler()
  Input: ALPS - force stream mode
  Input: iforce - minor clean-ups
  Input: iforce - fix force feedback not working
  Input: adbhid - do not access input_dev->private directly
  Input: logips2pp - add type 72 (PS/2 TrackMan Marble)

This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.

The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:

http://openocd.berlios.de/web/
http://www.olimex.com/dev/arm-usb-ocd.htmlSigned-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the newly released Aircard 595U EVDO
modem to the Sierra Wireless driver (sierra.c) in kernel 2.6.21.

I suspect that my mailer may be mangling patches so let me know and
I'll try to resend it.


From: Danny Budik <dbudik@ist-traffic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a problem reported with consecutive reads in the ldusb
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as910) fixes a ratelimit modification so that the
original error-handling path will be followed even when the log-rate
limitation kicks in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as906) improves the error handling for the USB power/level
attribute file.  If an error occurs, the original power-level settings
will be restored.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as881b) makes the ksuspend_usb_wq workqueue freezable.  We
don't want a rogue workqueue thread running around, unexpectedly
suspending or resuming USB devices in the middle of a system sleep
transition.

This fixes Bugzilla #8498.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This fixes a bug in an OHCI quirk handler for Portege 4000; the
Subvendor is 0x1179 (PCI_VENDOR_ID_TOSHIBA)
not 0x102f (PCI_VENDOR_ID_TOSHIBA_2)

bugid 8510

00:02.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10 [OHCI])
        Subsystem: Toshiba America Info Systems Unknown device [1179:0004]
        Flags: bus master, medium devsel, latency 64, IRQ 11
        Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Looks like the error path had a copy-paste error. The normal exit path
uses correct URB already.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix debug output. Previously, it would output "0xFFFFFFB0" on 32-bit
archs (and probably "0xFFFFFFFFFFFFFFB0" on 64-bits), because buf is
taken as signed char, which is promoted to signed int, while %x always
expects an unsigned int.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.

Also, do not access input_dev->private directly, use helpers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as907) prevents us from trying to allocate 0 bytes
when an interface has no endpoint descriptors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as905) removes a micro-optimization from the hub port
initialization code.  Previously we had been using a short timeout on
the first attempt the read the device descriptor; now we will use the
standard timeout length.

It's not clear that the short timeout ever provided any benefit.  And
now we know of one case where it actually hurts: The device can't meet
the short timeout and then it gets terminally confused.

This fixes Bugzilla #8444.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I haven't personally run across an oops because of this, but I feel safer
with this fix in place.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If this down_interruptible() does fail due to signal_pending() then the state
of the driver will get trashed in interesting ways, because userspace cannot
and will not retry the close().

Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Change PORT_WIDTH bit for UMTI_WIDE mode and fix a compile warning
introduced in last revision.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as902) fixes a mistake I introduced into usb_bulk_msg().
usb_fill_int_urb() already does the bit-shifting calculation for
high-speed Interrupt intervals; it shouldn't be done twice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>

Hello,

I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.

The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.

From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as883) removes an out-of-date WARN_ON from the main HCD
endpoint-disable routine.  The warning is triggered whenever an
endpoint is disabled while the root hub is suspended.  In the past
that may not have been legal, but it definitely is legal now.  Merely
unbinding a USB driver will do it.

Furthermore, I've never seen any occurrences of this warning that
really did signal an actual bug or error condition.  At this point it
has outlived its purpose.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

This patch (as879) ties up some loose ends from an earlier patch.
These are things I didn't think to include at the time but which
clearly belonged there.

	If an autosuspend fails because driver activity races with
	the autosuspend call, restart the autosuspend timer.

	When a device is resumed by an external request, it counts
	as device activity and should update the last_busy time so
	that the next autoresume won't occur immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as882) fixes a problem with the EHCI BIOS handoff.  On my
machine, the BIOS configures the controller and the handoff fails,
leaving the controller configured.  During resume-from-disk, this
confuses ehci-hcd into thinking that the controller has not been
tampered with.

The problem is fixed by turning off the Configured Flag whenever a
BIOS handoff is attempted, whether it succeeds or not.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This fixes the issue of drivers claiming multiple interfaces. Operations
are stopped as soon as an interface is suspend and resumed only as
all interfaces have been resumed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This just removes some warnings generated by the Docbook tools when
turning USB (host and peripheral side) kerneldoc into HTML; they're
all about missing ID attributes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Workaround another device firmware bug, wherein CDC descriptors get
placed in a wrong place never previously observed in the wild.

Fix a bug where a seeming RNDIS device returns a bogus response during
device initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Partial fix for bogosity in the ftdi-elan and u132-hcd drivers ... these
have no business including with the internals of other drivers, much less
doing so in a broken way!!

A previous patch resolved one build fix, this resolves another...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Sitecom WL-117 is another "driverless" ZD1211 device where the virtual
windows driver CD must be ejected before the WLAN device appears.

zd1211rw takes care of the ejecting, but usb-storage must be told not to claim
the device.

From: Matthew Davidson <mj.davidson@gmail.com>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this useless check should be removed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

the transfer of allocating the descriptor in attach and no longer in open
was incomplete resulting in a memory leak coverity spotted. This fix
is against the patch set you posted.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In commit [1] the SPI mode is set to 1, but it should be 0.  As stated
in the commit, ads784x samples the data on the rising edge.  SPI mode 1
samples on the falling edge [2] though.

The root cause of this is a bug in the omap_uwire code, which treats
CPHA=1 incorrectly; so these two bugs cancel each other out on one
of the main regression test platforms for this driver.

[1] kernel.org GIT 7937e86a
[2] http://en.wikipedia.org/wiki/Serial_Peripheral_Interface_BusSigned-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The TSC2046 is an updated version of the ADS7846 ... mention that in
the Kconfig helptext and driver source.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This is required to load it as a module, as GPL-compatible
license is necessary to use workqueues.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Fix Philips UCB1400 driver to use sched_setscheduler() instead of setting
the fields of task_struct directly.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>