Dongle shipped with Logitech DiNovo Edge (0x046d/0xc714) behaves in a weird
non-standard way - it contains multiple reports with the same usage, which
results in remapping of GenericDesktop.X and GenericDesktop.Y usages to
GenericDesktop.Z and GenericDesktop.RX respectively, thus rendering the
touchwheel unusable.

The commit 35068976 solved this
in a way that it didn't remap certain usages. This however breaks
(at least) middle button of Logic3 / SpectraVideo (0x1267/0x0210),
which in contrary requires the remapping.

To make both of the harware work, allow remapping of these usages again,
and introduce a quirk for Logitech DiNovo Edge "touchwheel" instead - we
disable remapping for key, abs and rel events only for this hardware.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Update MAITAINERS entry for HID and USB HID, adding
location of HID git tree.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This patch makes extra keys (F1-F12 in special mode, zooming, rotate, shuffle)
on Logitech S510 keyboard work.

Logitech S510 keyboard sends in report no. 3 keys which are far above the
logical maximum described in descriptor for given report.

This patch introduces a HID quirk for this wireless USB receiver/keyboard
in order to fix the report descriptor before it's being parsed - the logical
maximum and the number of usages is bumped up to 0x104d). The values are in the
"Reserved" area of consumer HUT, so HID_MAX_USAGE had to be changed too.

In addition to proper extracting of  the values from report descriptor, proper
HID-input mapping is introduced for them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Freeing of device->collection is properly done in hid_free_device() (as
this function is supposed to free all the device resources and could be
called from transport specific code, e.g. usb_hid_configure()).

Remove all kfree() calls preceeding the hid_free_device() call.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Every file should include the headers containing the prototypes for
it's global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

d4ae650a introduced zeroing of the
last field byte in output reports in order to make sure the unused
bits are set to 0. This is done in a wrong way, resulting in a
wrong bits being zeroed out (not properly shifted by the field offset
in the report). Fix this.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Report descriptor should be output when CONFIG_HID_DEBUG is defined.

This also mitigates the need for DEBUG and DEBUG_DATA defines, so let's
remove them.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Too many changes for comfort since -rc1.  Some missed merges, and some
just annoyingly big fixes since.  This is not how an -rc2 should look.
Need to really calm things down!

When the PCI controller OBP node lacks an interrupt-map
and interrupt-map-mask property, we need to form the
INO by hand.  The PCI swizzle logic was not doing that
properly.

This was a regression added by the of_device code.
Signed-off-by: David S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] fix compile errors

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (52 commits)
  netxen: do_rom_fast_write error handling
  natsemi: Fix detection of vanilla natsemi cards
  net: remove a collection of unneeded #undef REALLY_SLOW_IO stuff
  chelsio: Fix non-NAPI compile
  cxgb3 - Feed Rx free list with pages
  cxgb3 - Recovery from HW starvation of response queue entries.
  cxgb3 - Unmap offload packets when they are freed
  cxgb3 - FW version update
  cxgb3 - private ioctl cleanup
  cxgb3 - manage sysfs attributes per port
  S2IO: Restoring the mac address in s2io_reset
  S2IO: Avoid printing the Enhanced statistics for Xframe I card.
  S2IO: Making LED off during LINK_DOWN notification.
  S2IO: Added a loadable parameter to enable or disable vlan stripping in frame.
  S2IO: Optimized the delay to wait for command completion
  S2IO: Fixes for MSI and MSIX
  qla3xxx: Bumping driver version number
  qla3xxx: Kernic Panic on pSeries under stress conditions
  qla3xxx: bugfix tx reset after stress conditions.
  qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()
  ...

* 'jffs-maint' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  remove the jffs MAINTAINERS entry

Compiler warning spots real error!

The function do_rom_fast_read called in do_rom_fast_write can fail
and leave data1 unset. This causes a compile warning.
The correct thing is to propagate the error out.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch removes the MAINTAINERS entry for the removed jffs
filesystem.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Bob Tracy <rct@gherkin.frus.com> reported that the addition of support
for Aculab E1/T1 cPCI carrier cards broke detection of vanilla natsemi
cards.  This patch fixes that: the problem is that the driver-specific
ta in the PCI device table is an index into a second table and this
had not been updated for the vanilla cards.

This patch fixes the problem minimally.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Chelsio without NAPI enabled has been broken (won't compile) since
3de00b89 ("chelsio: NAPI speed improvement"):

    drivers/net/chelsio/sge.c: In function `t1_interrupt`:
    drivers/net/chelsio/sge.c:1716: error: `Q` undeclared (first use in this function)

The change below seems to add back in the declaration and
initialization of `Q` that was removed by mistake, and at least makes
the driver compile for me, although I have no hardware and hence no
way to test whether this actually works.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Populate Rx free list with pages.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Improve the traffic recovery after the HW ran out of response queue entries.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Offload packets may be DMAed long after their SGE Tx descriptors are done
so they must remain mapped until they are freed rather than until their
descriptors are freed.  Unmap such packets through an skb destructor.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update FW version to 3.2
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Clean up some private ioctls.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sysfs attributes are now managed per port, no longer per adapter.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Restore in s2io_reset, the mac address assigned during s2io_open.
  Earlier, it was getting overwritten to the factory default (read from the
  eeprom) and subsequently dropping received frames.

- Fixed the typo in calling rtnl_unlock in s2io_set_link function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Enhanced Statistics are supported only for Xframe II (Herculas) card. Add
  condition check such Enhanced statistics will included only in the case of
  Xframe II card.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Turning off LED for LINK_DOWN notification
- Return from rxd_owner_bit_reset function if call to set_rxd_buffer_pointer
  fails with ENOMEM
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Added code to not to strip vlan tag when driver is in promiscuous mode
- Added module loadable parameter 'vlan_tag_strip" through which user can
  enable or disable vlan stripping irrespective of mode
  ( promiscuous or non-promiscuous ).
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Optimized delay to wait for command completion so as to reduce the
  initialization wait time.
- Disable differentiated services steering. By default RMAC is configured to
  steer traffic with certain DS codes to other queues. Driver must initialize
  the DS memory to 0 to make sure that DS steering will not be used by default.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

- Added debug statements to print a debug message if the MSI/MSI-X vector (or)
  data is zero.

- This patch removes the code that will enable NAPI for the case of single
  ring and MSI-X / MSI case. There are some issue in the enabling NAPI with
  MSI/MSI-X.  So we are turning off NAPI in the case of MSI/MSI-X.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

To reproduce this panic consistently, we run an intensive network
application like 'netperf'. After waiting for a couple of seconds,
you will see a stack trace and a kernel panic where we are calling
pci_unmap_single() in ql_poll().

Changes:
1)  Check the flags on the Response MAC IO Control block to check for
errors
2)  Ensure that if we are on the 4022 we only use one segment
3)  Before, we were reading the memory mapped producer index register
everytime we iterated in the loop when clearing the queue.  We should
only be iterating to a known point, not as the producer index
is being updated.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

To Reproduce the Problem:
To reproduce this panic consistently, we run an intensive network
application like 'netperf' and then switch to a different console.
After waiting for a couple of seconds, you will see a tx reset has occured.

Reason:
We enable interrupts even if we were not running.

Solution:
Now we will enable interrupts only after we are ready to give up the poll
routine.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()

pci_map_single() could fail.  We need to properly check the return
code from pci_map_single().  If we can not properly map this address,
then we should cleanup and return the proper return code.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The scatter/gather lists were not being build correctly.  When
large frames spanned several buffers the chip would panic.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This change removes use of constants for rx buffer queue size
and instead calculates the queue length based on what he MTU
is set to.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This network device driver shares the same hardware as the qla4xxx
iSCSI driver. Changing the MTU via the device interface will
cause qla4xxx to crash as there is no way to make notification.
Users wishing to change the MTU must do so using an iSCSI
utility such as Qlogic SanSurfer. This forces the user to
unload/reload this network device driver after the MTU
value has been changed in flash.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing
   through the Link State Machine
2) Fix deadlock issue when ethtool would call ql_get_settings()
3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>