- 25 May, 2007 13 commits
-
-
Mark Fasheh authored
We weren't calling this before, but since ocfs2 handles the entire truncate operation, we should. Signed-off-by:Mark Fasheh <mark.fasheh@oracle.com>
-
Mark Fasheh authored
Similarly to the page lock / cluster lock inversion in ocfs2_readpage, we can deadlock on ip_alloc_sem. We can down_read_trylock() instead and just return AOP_TRUNCATED_PAGE if the operation fails. Signed-off-by: -
Linus Torvalds authored
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (25 commits) [XFRM]: Allow packet drops during larval state resolution. [CASSINI]: Check pci_set_mwi() return value. [NET]: "wrong timeout value" in sk_wait_data() v2 [NETFILTER]: nf_nat_h323: call set_h225_addr instead of set_h225_addr_hook [NETFILTER]: nf_conntrack_h323: add missing T.120 address in OLCA [NETFILTER]: nf_conntrack_h323: remove unnecessary process of Information signal [NETFILTER]: nf_conntrack_h323: fix get_h225_addr() for IPv6 address access [NETFILTER]: nf_conntrack_h323: fix ASN.1 types [NETFILTER]: nf_conntrack_ftp: fix newline sequence number calculation [NETFILTER]: nf_conntrack_ftp: fix newline sequence number update [NET_SCHED]: sch_htb: fix event cache time calculation [DCCP]: Fix build warning when debugging is disabled. [TIPC]: Fixed erroneous introduction of for_each_netdev [RTNETLINK]: Fix sending netlink message when replace route. [TR]: Use menuconfig objects. [ARCNET]: Use menuconfig objects. [TIPC]: Use menuconfig objects. [SCTP]: Use menuconfig objects. [IPVS]: Use menuconfig objects. [DCCP]: Use menuconfig objects. ...
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: pata_via: Handle laptops via DMI libata: -ENODEV during prereset isn't an error libata: don't consider 0xff as port empty if SStatus is available ata_piix: add short 40c quirk for Acer Aspire 2030, take #2 pata_sis: Fix and clean up some timing setups hpt3x2n: Correct revision boundary
-
David S. Miller authored
The current IPSEC rule resolution behavior we have does not work for a lot of people, even though technically it's an improvement from the -EAGAIN buisness we had before. Right now we'll block until the key manager resolves the route. That works for simple cases, but many folks would rather packets get silently dropped until the key manager resolves the IPSEC rules. We can't tell these folks to "set the socket non-blocking" because they don't have control over the non-block setting of things like the sockets used to resolve DNS deep inside of the resolver libraries in libc. With that in mind I coded up the patch below with some help from Herbert Xu which provides packet-drop behavior during larval state resolution, controllable via sysctl and off by default. This lays the framework to either: 1) Make this default at some point or... 2) Move this logic into xfrm{4,6}_policy.c and implement the ARP-like resolution queue we've all been dreaming of. The idea would be to queue packets to the policy, then once the larval state is resolved by the key manager we re-resolve the route and push the packets out. The packets would timeout if the rule didn't get resolved in a certain amount of time. Signed-off-by:David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6Linus Torvalds authored
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] acpi_get_sysname() should be __init [IA64] Cleanup acpi header to reuse the generic _PDC defines [IA64] Fix using uninitialized data in _PDC setup [IA64] start_secondary() and smp_callin() should be __cpuinit
-
Alan Cox authored
Oh the joy of saving a fraction of a cent using short 40 wire cables and not faking 80wire Teach the VIA driver that there are some systems we need to know are magically wired for high speeds. Signed-off-by:
Alan Cox <alan@redhat.com> Tested-by:
Francis Russell <FrancisRussell@btinternet.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Tejun Heo authored
During prereset, -ENODEV return from ata_wait_ready() is not an error. This causes unnecessary bug message on controllers which uses 0xff to indicate empty port. Fix it. Signed-off-by:
Tejun Heo <htejun@gmail.com> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by:
-
Tejun Heo authored
Some SATA controllers (sata_sil) use 0xff to indicate port not ready status, not port empty. As libata interprets 0xff as port empty, this causes unnecessary reset failure and retry. Don't consider 0xff as port empty if SStatus is available and indicates that port is online. Signed-off-by:
-
Tejun Heo authored
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it. Signed-off-by:
-
Alan Cox authored
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new generation controllers in error. - Use byte size operations where it is cleaner for mode setup - Fix a couple of masking errors on certai chip revs when setting speeds Signed-off-by:
-
Alan Cox authored
We have a revision that isn't correctly claimed as two drivers both go for it: Fix the test accordingly. Noticed originally by Bill Nottingham. Signed-off-by:
-
- 24 May, 2007 27 commits
-
-
Vasily Averin authored
sys_setsockopt() do not check properly timeout values for SO_RCVTIMEO/SO_SNDTIMEO, for example it's possible to set negative timeout values. POSIX do not defines behaviour for sys_setsockopt in case negative timeouts, but requires that setsockopt() shall fail with -EDOM if the send and receive timeout values are too big to fit into the timeout fields in the socket structure. In current implementation negative timeout can lead to error messages like "schedule_timeout: wrong timeout value". Proposed patch: - checks tv_usec and returns -EDOM if it is wrong - do not allows to set negative timeout values (sets 0 instead) and outputs ratelimited information message about such attempts. Signed-off-By:
Vasily Averin <vvs@sw.ru> Signed-off-by:
-
-
Jing Min Zhao authored
They're the same. Signed-off-by:
Jing Min Zhao <zhaojingmin@vivecode.com> Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
Jing Min Zhao authored
Add missing process of T.120 address in OpenLogicalChannelAck signal. Signed-off-by:
-
Jing Min Zhao authored
According to the implementation of H.323, it's not necessary to check the addresses in Information signals. Signed-off-by:
-
Jing Min Zhao authored
Update get_h225_addr() to meet the changes in ASN.1 types. It was using field ip6 to access IPv6 TransportAddress, it should be ip according the ASN.1 definition. Signed-off-by:
-
Jing Min Zhao authored
1. Add support for decoding IPv6 address. I know it was manually added in the header file, but not in the template file. That wouldn't work. 2. Add missing support for decoding T.120 address in OLCA. 3. Remove unnecessary decoding of Information signal. Signed-off-by:
-
Patrick McHardy authored
When the packet size is changed by the FTP NAT helper, the connection tracking helper adjusts the sequence number of the newline character by the size difference. This is wrong because NAT sequence number adjustment happens after helpers are called, so the unadjusted number is compared to the already adjusted one. Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn> Signed-off-by:
-
Patrick McHardy authored
When trying to locate the oldest entry in the history of newline character sequence numbers, the sequence number of the current entry is incorrectly compared with the index of the oldest sequence number instead of the number itself. Additionally it is not made sure that the current sequence number really is after the oldest known one. Based on report by YU, Haitao <yuhaitao@tsinghua.org.cn> Signed-off-by:
-
Patrick McHardy authored
The event cache time must be an absolute value, when no event exists it is incorrectly set to 1s instead of 1s in the future. Signed-off-by:
-
David S. Miller authored
Signed-off-by: -
Jon Paul Maloy authored
Signed-off-by:
Jon Paul Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Milan Kocian authored
When you replace route via ip r r command the netlink multicast message is not send. This patch corrects it. NL message is sent with NLM_F_REPLACE flag. Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8320Signed-off-by:
Milan Kocian <milon@wq.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
Jan Engelhardt <jengelh@gmx.de> Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Jan Engelhardt authored
Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by:
-
Matthias Kaehlcke authored
Use mutex instead of binary semaphore in idt77252 driver. Signed-off-by:
Matthias Kaehlcke <matthias.kaehlcke@gmail.com> Signed-off-by:
-
Oliver Hartkopp authored
Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Urs Thuermann <urs@isnogud.escape.de> Signed-off-by:
-
Herbert Xu authored
My previous patch that changed the return value of qdisc_restart incorrectly made the case where dequeue returns empty continue processing packets. This patch is based on diagnosis and fix by Patrick McHardy. Reported-and-debugged-by:
Anant Nitya <kernel@prachanda.info> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: forcedeth: fix cpu irq mask chelsio parenthesis fix spidernet: skb used after netif_receive_skb meth driver renovation remove unnecessary dependency on VIA velocity config fix compiler warning in fixed.c asix.c - Add Belkin F5D5055 ids ucc_geth:trivial fix ucc_geth: Fix MODULE_DEVICE_TABLE() duplication [PATCH] drivers/net/wireless/libertas/rx.c: fix use-after-free [PATCH] drivers/net/wireless/libertas/fw.c: fix use-before-check [PATCH] libertas: skb dereferenced after netif_rx
-
Ayaz Abdulla authored
This patch fixes the cpu irq mask define to include the timer irq. Another flag check was setting up the timer bit in all cases so we didn't notice the issue. Signed-off-by:
Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by:
-
Mariusz Kozlowski authored
Hello, Balanance parenthesis in chelsio header file. Signed-off-by:
Mariusz Kozlowski <m.kozlowski@tuxland.pl> drivers/net/chelsio/suni1x10gexp_regs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) Signed-off-by:
-
Florin Malita authored
The stats update code in spider_net_pass_skb_up() is touching the skb after it's been passed up to the stack. To avoid that, just update the stats first. Signed-off-by:
Florin Malita <fmalita@gmail.com> Signed-off-by:
Linas Vepstas <linas@austin.ibm.com> Signed-off-by:
-
Ralf Baechle authored
The meth ethernet driver for the SGI IP32 aka O2 is so far still an old style driver which does not use the device driver model. This is now causing issues with some udev based gadgetry in debian-stable. Fixed by converting the meth driver to a platform device. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> -- Fixes since previous patch: o Fixed typo in meth_exit_module() Signed-off-by:
-
