Lock sections don't work the new dwarf2 unwinder
This generates slightly smaller code. It adds one more taken
jump to the fast path.

Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>

Make translation_disabled a uchar rather than an int
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

The pci_get_device() API decrements the reference count on the 'from'
parameter when it continues searching. Therefore, take a ref count on
Calgary bus when we initialize them in either translated or
non-translated mode.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

We were freeing the iommu_table and leaking the bitmap pages. Also
rename it to calgary_free_bus, which is more accurate.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

Move the tce_table_kva array, disabled bitmap and bus_to_phb array
into a new per bus 'struct calgary_bus_info'. Also slightly reorganize
build_tce_table and tce_table_setparms to avoid exporting bus_info to
tce.c.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

Rearrange struct members loosely based on size for improved alignment
and to save a few bytes.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

Describes the stack organization on x86-64.

I changed it a bit and removed some obsolete information and the
questions.

Cc: kaos@sgi.com
Signed-off-by: Andi Kleen <ak@suse.de>

Move initialization of all memory end variables to as early as
possible, so that dependent code doesn't need to check whether these
variables have already been set.

Change the range check in kunmap_atomic to actually make use of this
so that the no-mapping-estabished path (under CONFIG_DEBUG_HIGHMEM)
gets used only when the address is inside the lowmem area (and BUG()
otherwise).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>

The genapic field and the accessor macro weren't used anywhere.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>

While an earlier patch already did a small step into that direction,
this patch moves initialization of all memory end variables to as
early as possible, so that dependent code doesn't need to check
whether these variables have already been set.

Also, remove a misleading (perhaps just outdated) comment, and make
static a variable only used in a single file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>

CVS hasn't been used for a long time for them.
Signed-off-by: Andi Kleen <ak@suse.de>

... instead of using a CONFIG option. The config option still controls
if the resulting executable actually has unwind information.

This is useful to prevent compilation errors when users select
CONFIG_STACK_UNWIND on old binutils and also allows to use
CFI in the future for non kernel debugging applications.

Cc: jbeulich@novell.com
Cc: sam@ravnborg.org
Signed-off-by: Andi Kleen <ak@suse.de>

Makes code a little shorter.
Signed-off-by: Andi Kleen <ak@suse.de>

Remove some unlinuxy ways to write function parameter definitions.
Remove some stray "return;"s

No functional change.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

No functional changes.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

They are not used in this file so remove them. i386 didn't have them either.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

It used to contain support code for NUMAQ, but that is long gone already
on 64bit.
Signed-off-by: Andi Kleen <ak@suse.de>

Since we only support PCI and ISA legacy busses now there is no need to
have an full array with checking.
Signed-off-by: Andi Kleen <ak@suse.de>

They did not really belong into io_apic.c. Move them into a new file
and clean it up a bit.

Also remove outdated ATI quirk that was obsolete,
Signed-off-by: Andi Kleen <ak@suse.de>

The MPS table specification says that the operating system should
renumber the IO-APICs following the table as needed.  However in
ACPI this is not allowed or neeeded and all x86-64 systems are ACPI
compliant.

The code was already disabled on some systems because it caused
problems there. Remove it completely now.

CC: mdomsch@dell.com
Signed-off-by: Andi Kleen <ak@suse.de>

Bugzilla #6552 says:

"In arch/i386/boot/setup.S, movw is used instead of movb for PS/2 mouse
information, although it is unsigned char. This does not harm, because
the jmp instruction overwritten by movw is used before executing movw,
and never be used again"

I've no idea if this is a real bug or how it gets fixed, so I'm submitting
it for review instead of letting it die of boredom in bugzilla. Aditionally
to i386, I've changed x86-64, which mirrors the same code.

Credits to Yoshinori K. Okuji, who found the problem and suggested a fix.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>

The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions

In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.

Similar to earlier x86-64 patch.

Includes a fix by Jiri Slaby for a mistake that broke resume
Signed-off-by: Andi Kleen <ak@suse.de>

The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions

In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.
Signed-off-by: Andi Kleen <ak@suse.de>

It apparently has never triggered in many years.
Signed-off-by: Andi Kleen <ak@suse.de>

PIC mode is an outdated way to drive the APICs that was used on
some early MP boards. It is not supported in the ACPI model.

It is unlikely to be ever configured by any x86-64 system

Remove it thus.
Signed-off-by: Andi Kleen <ak@suse.de>

No 64bit EISA or Microchannel systems ever. Remove the left over code
in the IO-APIC driver and the mptable parser
Signed-off-by: Andi Kleen <ak@suse.de>

This was an old workaround for broken MP-BIOS. The user could
specify overwrites on the command line.

I've never seen it being used for anything on 64bit. So get
rid of it for now.
Signed-off-by: Andi Kleen <ak@suse.de>

And remove some old obsolete ones.
Signed-off-by: Andi Kleen <ak@suse.de>

(based on x86-64 changes)
- Add a proper memory clobber to invlpg
- Remove an unused extern
Signed-off-by: Andi Kleen <ak@suse.de>

- Convert CR* accesses to dedicated inline functions and rewrite
the rest as C inlines
- Don't do a double flush for global flushes (pointed out by Zach Amsden)
This was a bug workaround for old CPUs that don't do 64bit and is obsolete.
- Add a proper memory clobber to invlpg
- Remove an unused extern
Signed-off-by: Andi Kleen <ak@suse.de>

The new systems already use focus disabled and the comment was
completely outdated.
Signed-off-by: Andi Kleen <ak@suse.de>

Nobody has been setting the mismatch counter and the ifdef was never
set so remove it.
Signed-off-by: Andi Kleen <ak@suse.de>

IO-APIC or local APIC can only be disabled at runtime anyways and
Kconfig has forced these options on for a long time now.

The Kconfigs are kept only now for the benefit of the shared acpi
boot.c code.
Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Andi Kleen <ak@suse.de>

And move the comment to a proper place.
Signed-off-by: Andi Kleen <ak@suse.de>

- Move them to a pure assembly file. Previously they were in
a C file that only consisted of inline assembly. Doing it in pure
assembler is much nicer.
- Add a frame.i include with FRAME/ENDFRAME macros to easily
add frame pointers to assembly functions
- Add dwarf2 annotation to them so that the new dwarf2 unwinder
doesn't get stuck on them
- Random cleanups

Includes feedback from Jan Beulich and a UML build fix from Andrew
Morton.

Cc: jbeulich@novell.com
Cc: jdike@addtoit.com
Signed-off-by: Andi Kleen <ak@suse.de>

LOCK_PREFIX is replaced by nops on UP systems, so it has to be a special
macro.  Previously this was only possible from C. Allow it for pure
assembly files too. Similar to earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>

Previously it didn't align. Use the same one as the C compiler
in blended mode, which is good for K8 and Core2 and doesn't hurt
on P4.
Signed-off-by: Andi Kleen <ak@suse.de>