Provide some output for debugging the driver.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The unified ioat1/ioat2 ioat_dma_unmap() implementation derives the
source and dest addresses from the unmap descriptor.  There is no longer
a need to track this information in struct ioat_desc_sw.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Replace the current linked list munged into a ring with a native ring
buffer implementation.  The benefit of this approach is reduced overhead
as many parameters can be derived from ring position with simple pointer
comparisons and descriptor allocation/freeing becomes just a
manipulation of head/tail pointers.

It requires a contiguous allocation for the software descriptor
information.

Since this arrangement is significantly different from the ioat1 chain,
move ioat2,3 support into its own file and header.  Common routines are
exported from driver/dma/ioat/dma.[ch].
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Prepare the code for the conversion of the ioat2 linked-list-ring into a
native ring buffer.  After this conversion ioat2 channels will share
less of the ioat1 infrastructure, but there will still be places where
sharing is possible.  struct ioat_chan_common is created to house the
channel attributes that will remain common between ioat1 and ioat2
channels.

For every routine that accesses both common and hardware specific fields
the old unified 'ioat_chan' pointer is split into an 'ioat' and  'chan'
pointer.  Where 'chan' references common fields and 'ioat' the
hardware/version specific.

[ Impact: pure structure member movement/variable renames, no logic changes ]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

If a callback is to be attached to a descriptor the channel needs to
know at ->prep time so it can set the interrupt enable bit.  This is in
preparation for moving descriptor ioat2 descriptor preparation from
->submit to ->prep.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The async_tx api assumes that after a successful ->prep a subsequent
->submit will not fail due to a lack of resources.

This also fixes a bug in the allocation failure case.  Previously the
descriptors allocated prior to the allocation failure would not be
returned to the free list.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

This cleans up a mess of and'ing and or'ing bit definitions, and allows
simple assignments from the specified dma_ctrl_flags parameter.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

->dmacount tracks the sequence number of active descriptors.  It is
written to the DMACOUNT register to update the channel's view of pending
descriptors in the chain.  The register is 16-bits so ->dmacount should
be unsigned and 16-bit as well.  Also modify ->desccount to maintain
alignment.

This was never a problem in practice because we never compared dmacount
values, but this is a bug waiting to happen.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Towards the removal of ioatdma_device.version split the initialization
path into distinct versions.  This conversion:
1/ moves version specific probe code to version specific routines
2/ removes the need for ioat_device
3/ turns off the ioat1 msi quirk if the device is reinitialized for intx
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The only .c files that utilize these protected prototypes depend on
CONFIG_INTEL_IOATDMA=y, so there is no value gained in providing empty
prototypes.

[ Impact: pure cleanup ]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

* reduce device->common. to dma-> in ioat_dma_{probe,remove,selftest}
* ioat_lookup_chan_by_index to ioat_chan_by_index
* multi-line function definitions
* ioat_desc_sw.async_tx to ioat_desc_sw.txd
* desc->txd. to tx-> in cleanup routine
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The driver currently duplicates much of what these routines offer, so
just use the common code.  For example ->irq_mode tracks what interrupt
mode was initialized, which duplicates the ->msix_enabled and
->msi_enabled handling in pcim_release.

This also adds a check to the return value of dma_async_device_register,
which can fail.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Some of these defines may be useful outside of dma.c and the header is
private so there are no namespace pollution concerns.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

When first created the ioat driver was the only inhabitant of
drivers/dma/.  Now, it is the only multi-file (more than a .c and a .h)
driver in the directory.  Moving it to an ioat/ subdirectory allows the
naming convention to be cleaned up, and allows for future splitting of
the source files by hardware version (v1, v2, and v3).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.

mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card.  I have tested this, and removing the !
fixes the problem.

Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit code, we scan buffers attached to a transaction.  During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
 But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head.  So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.

This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent ->lookup() deadlock correction required the directory inode
mutex to be dropped while waiting for expire completion.  We were
concerned about side effects from this change and one has been identified.

I saw several error messages.

They cause autofs to become quite confused and don't really point to the
actual problem.

Things like:

handle_packet_missing_direct:1376: can't find map entry for (43,1827932)

which is usually totally fatal (although in this case it wouldn't be
except that I treat is as such because it normally is).

do_mount_direct: direct trigger not valid or already mounted
/test/nested/g3c/s1/ss1

which is recoverable, however if this problem is at play it can cause
autofs to become quite confused as to the dependencies in the mount tree
because mount triggers end up mounted multiple times.  It's hard to
accurately check for this over mounting case and automount shouldn't need
to if the kernel module is doing its job.

There was one other message, similar in consequence of this last one but I
can't locate a log example just now.

When checking if a mount has already completed prior to adding a new mount
request to the wait queue we check if the dentry is hashed and, if so, if
it is a mount point.  But, if a mount successfully completed while we
slept on the wait queue mutex the dentry must exist for the mount to have
completed so the test is not really needed.

Mounts can also be done on top of a global root dentry, so for the above
case, where a mount request completes and the wait queue entry has already
been removed, the hashed test returning false can cause an incorrect
callback to the daemon.  Also, d_mountpoint() is not sufficient to check
if a mount has completed for the multi-mount case when we don't have a
real mount at the base of the tree.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The massive nommu update (8feae131) resulted in these warnings:
ipc/shm.c: In function `sys_shmdt':
ipc/shm.c:974: warning: unused variable `size'
ipc/shm.c:972: warning: unused variable `next'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  kvm: fix kvm reboot crash when MAXSMP is used
  cpumask: alloc zeroed cpumask for static cpumask_var_ts
  cpumask: introduce zalloc_cpumask_var

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  bsg: setting rq->bio to NULL

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  cls_cgroup: Fix oops when user send improperly 'tc filter add' request
  r8169: fix crash when large packets are received

* 'for-linus' of git://neil.brown.name/md:
  md/raid5: fix bug in reshape code when chunk_size decreases.
  md/raid5 - avoid deadlocks in get_active_stripe during reshape
  md/raid5: use conf->raid_disks in preference to mddev->raid_disk

Due to commit 1cd96c24 ("block: WARN
in __blk_put_request() for potential bio leak"), BSG SMP requests get
the false warnings:

WARNING: at block/blk-core.c:1068 __blk_put_request+0x52/0xc0()

This sets rq->bio to NULL to avoid that false warnings.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

one system was found there is crash during reboot then kvm/MAXSMP
Sending all processes the KILL signal...                              done
Please stand by while rebooting the system...
[ 1721.856538] md: stopping all md devices.
[ 1722.852139] kvm: exiting hardware virtualization
[ 1722.854601] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1722.872219] IP: [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1722.877955] PGD 0
[ 1722.880042] Oops: 0000 [#1] SMP
[ 1722.892548] last sysfs file: /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:2:0/0:2:0:0/vendor
[ 1722.900977] CPU 9
[ 1722.912606] Modules linked in:
[ 1722.914226] Pid: 0, comm: swapper Not tainted 2.6.30-rc7-tip-01843-g2305324-dirty #299 ...
[ 1722.932589] RIP: 0010:[<ffffffff8102c6b6>]  [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1722.942709] RSP: 0018:ffffc900010b6ed8  EFLAGS: 00010046
[ 1722.956121] RAX: 0000000000000000 RBX: ffffc9000e253140 RCX: 0000000000000009
[ 1722.972202] RDX: 000000000000b020 RSI: ffffc900010c3220 RDI: ffffffffffffd790
[ 1722.977399] RBP: ffffc900010b6f08 R08: 0000000000000000 R09: 0000000000000000
[ 1722.995149] R10: 00000000000004b8 R11: 966912b6c78fddbd R12: 0000000000000009
[ 1723.011551] R13: 000000000000b020 R14: 0000000000000009 R15: 0000000000000000
[ 1723.019898] FS:  0000000000000000(0000) GS:ffffc900010b3000(0000) knlGS:0000000000000000
[ 1723.034389] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[ 1723.041164] CR2: 0000000000000000 CR3: 0000000001001000 CR4: 00000000000006e0
[ 1723.056192] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1723.072546] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 1723.080562] Process swapper (pid: 0, threadinfo ffff88107e464000, task ffff88047e5a2550)
[ 1723.096144] Stack:
[ 1723.099071]  0000000000000046 ffffc9000e253168 966912b6c78fddbd ffffc9000e253140
[ 1723.115471]  ffff880c7d4304d0 ffffc9000e253168 ffffc900010b6f28 ffffffff81011022
[ 1723.132428]  ffffc900010b6f48 966912b6c78fddbd ffffc900010b6f48 ffffffff8100b83b
[ 1723.141973] Call Trace:
[ 1723.142981]  <IRQ> <0> [<ffffffff81011022>] kvm_arch_hardware_disable+0x26/0x3c
[ 1723.158153]  [<ffffffff8100b83b>] hardware_disable+0x3f/0x55
[ 1723.172168]  [<ffffffff810b95f6>] generic_smp_call_function_interrupt+0x76/0x13c
[ 1723.178836]  [<ffffffff8104cbea>] smp_call_function_interrupt+0x3a/0x5e
[ 1723.194689]  [<ffffffff81035bf3>] call_function_interrupt+0x13/0x20
[ 1723.199750]  <EOI> <0> [<ffffffff814ad3b4>] ? acpi_idle_enter_c1+0xd3/0xf4
[ 1723.217508]  [<ffffffff814ad3ae>] ? acpi_idle_enter_c1+0xcd/0xf4
[ 1723.232172]  [<ffffffff814ad4bc>] ? acpi_idle_enter_bm+0xe7/0x2ce
[ 1723.235141]  [<ffffffff81a8d93f>] ? __atomic_notifier_call_chain+0x0/0xac
[ 1723.253381]  [<ffffffff818c3dff>] ? menu_select+0x58/0xd2
[ 1723.258179]  [<ffffffff818c2c9d>] ? cpuidle_idle_call+0xa4/0xf3
[ 1723.272828]  [<ffffffff81034085>] ? cpu_idle+0xb8/0x101
[ 1723.277085]  [<ffffffff81a80163>] ? start_secondary+0x1bc/0x1d7
[ 1723.293708] Code: b0 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 e0 31 c0 48 8b 04 cd 30 ee 27 82 49 89 cc 49 89 d5 48 8b 04 10 48 8d b8 90 d7 ff ff <48> 8b 87 70 28 00 00 48 8d 98 90 d7 ff ff eb 16 e8 e9 fe ff ff
[ 1723.335524] RIP  [<ffffffff8102c6b6>] hardware_disable+0x4c/0xb4
[ 1723.342076]  RSP <ffffc900010b6ed8>
[ 1723.352021] CR2: 0000000000000000
[ 1723.354348] ---[ end trace e2aec53dae150aa1 ]---

it turns out that we need clear cpus_hardware_enabled in that case.
Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already.  Avoid surprises when MAXSMP is enabled.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

So can get cpumask_var with cpumask_clear
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

I found a bug in cls_cgroup_change() in cls_cgroup.c.
cls_cgroup_change() expected tca[TCA_OPTIONS] was set from user space properly,
but tc in iproute2-2.6.29-1 (which I used) didn't set it.

In the current source code of tc in git, it set tca[TCA_OPTIONS].

  git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/iproute2.git

If we always use a newest iproute2 in git when we use cls_cgroup, 
we don't face this oops probably.
But I think, kernel shouldn't panic regardless of use program's behaviour. 
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )

Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)

When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.

Fix is to tell to NIC what is the maximum size a frame can be.

This bug is very old, (before git introduction, linux-2.6.10), and 
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.
Signed-off-by: NeilBrown <neilb@suse.de>

md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts.  This is used to achieve a
stable state before making internal changes.

Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.

It is not necessary to inhibit reshape IO when a quiesce is
requested.  Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.

So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.

This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported.  So this patch is
not needed in earlier kernels.
Signed-off-by: NeilBrown <neilb@suse.de>

mddev->raid_disks can be changed and any time by a request from
user-space.  It is a suggestion as to what number of raid_disks is
desired.

conf->raid_disks can only be changed by the raid5 module with suitable
locks in place.  It is a statement as to the current number of
raid_disks.

There are two places where the latter should be used, but the former
is used.  This can lead to a crash when reshaping an array.

This patch changes to mddev-> to conf->
Signed-off-by: NeilBrown <neilb@suse.de>

Our async work synchronization was broken by "async: make sure
independent async domains can't accidentally entangle" (commit
d5a877e8), because it would report
the wrong lowest active async ID when there was both running and
pending async work.

This caused things like no being able to read the root filesystem,
resulting in missing console devices and inability to run 'init',
causing a boot-time panic.

This fixes it by properly returning the lowest pending async ID: if
there is any running async work, that will have a lower ID than any
pending work, and we should _not_ look at the pending work list.

There were alternative patches from Jaswinder and James, but this one
also cleans up the code by removing the pointless 'ret' variable and
the unnecesary testing for an empty list around 'for_each_entry()' (if
the list is empty, the for_each_entry() thing just won't execute).

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13474Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Outline udelay and fix a few issues.
  MIPS: ioctl.h: Fix headers_check warnings
  MIPS: Cobalt: PCI bus is always required to obtain the board ID
  MIPS: Kconfig: Remove "Support for" from Cavium system type
  MIPS: Sibyte: Honor CONFIG_CMDLINE
  SSB: BCM47xx: Export ssb_watchdog_timer_set

The previous patch submission had a I typo I didn't catch but Bartlomiej
noted. Guess this proves the point about any patch being risky late in an rc
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Explicity initialize cpus_hardware_enabled

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  pdc202xx_old: fix resetproc() method
  pdc202xx_old: fix 'pdc20246_dma_ops'

Outlining fixes the issue were on certain CPUs such as the R10000 family
the delay loop would need an extra cycle if it overlaps a cacheline
boundary.

The rewrite also fixes build errors with GCC 4.4 which was changed in
way incompatible with the kernel's inline assembly.

Relying on pure C for computation of the delay value removes the need for
explicit.  The price we pay is a slight slowdown of the computation - to
be fixed on another day.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Make ioctl.h compatible with asm-generic/ioctl.h and userspace

fix the following 'make headers_check' warning:

  usr/include/asm-mips/ioctl.h:64: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>