This tidies up the boot_cpu_data.flags probing on SH-4A. All of them have
a few things in common, which we can blindly set, rather than having each
subtype have to set the same flags. We can also make assumptions about
cache ways and the validity of PTEA, so this also kills off CPU_HAS_PTEA
as a config option. There was also a bug in the FPU probing, which is now
tidied up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This tidies up the L2 probing, as it may or may not be implemented on a
CPU, regardless of whether it is supported. This converts the cvr
validity checks from BUG_ON()'s to simply clearing the CPU_HAS_L2_CACHE
flag and moving on with life.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Hook up the shared 4-bit divisor clock code to sh7785.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add shared code for 4-bit divisor clocks.

Processor specific code can use SH_CLK_DIV4()
to initialize div4 clocks, and then use
sh_clk_div4_register() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Hook up the shared 32-bit module stop bit code to sh7785.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add shared 32-bit module stop bit clock support.

Processor specific code can use SH_CLK_MSTP32()
to initialize module stop bit clocks, and then
use sh_clk_mstp32() for registration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add the CPU_HAS_L2_CACHE flag to SH7724.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modifies the sh7785 clock code to use the MODE4
value to switch between 72x and 36x PLL multiplication.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds mode pin support to the sh7785lcr board.

The harware allows the user to control the mode pins using
dip switches S1 and S2, but from the software the pins are
fixed to the factory default since we have no way to reading
out this configuration from software.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds sh7785 mode pin definitions. Mode pins and
pin function controller comments are added as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add mode pin support for the SuperH architecture V2.

With this patch applied the board code can add their
own function to export the cpu mode pin configuration.
In most cases this will be a constant bitmap, but
boards that allow reading this from a register can
instead read out the pin state from hardware.

The code warns if a pin is tested but no board specific
mode pin function has been provided.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This fixes a build error where references to pci_cache_line_size are
undefined, as this ceases to be exported when PCI_DISABLE_MWI is enabled,
as is now the default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

None of the SH PCI controllers support MWI, it is always treated as a
direct memory write, so simply disable it outright. In the case of the
PCI cache line size, consult that for the pci_dma_burst_advice()
strategy, and switch over to PCI_DMA_BURST_MULTIPLE, as PPC64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

As there is only a single controller and remapping has no impact for the
address range in question, just initialize it directly in the controller
definition. This fixes up boot time warnings about not having the field
initialized.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch removes the ->build_rate_table() callback,
->recalc() may instead be used for this purpose.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch converts the sh7785 clock code to make use
of clk_rate_table_build() and clk_rate_table_round().
The ->build_rate_table() callback is removed, the
table building is instead handled in ->recalc().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add SuperH-specific clock framework helper functions:
- clk_rate_table_build() - build cpufreq table from divisors/multipliers
- clk_rate_table_round() - use cpufreq table to find matching frequency
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch converts the sh7785 pll implementation from the
all-in-one code in frqmr_recalc() and frqmr_build_rate_table()
to a separate struct clk. This allows us to remove the processor
specific multiplier and use generic rate table functions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds preliminary support for the ms7724se solution engine board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This kills off after_bootmem and switches to using slab_is_available()
instead. Presently the only place this is used is by the sh64 ioremap,
and there's not much point in keeping the reference around otherwise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds a new SH_CLK_CPG for parts that have CPG support.
SH_CLK_CPG_LEGACY is made to depend on this, and still needs to be set
for platforms that want clock-cpg to register the legacy clocks. With
this new config item in place, it is now possible to start layering more
generic CPG code in place while other platforms transition off of the
legacy clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds a NR_IRQS_LEGACY definition, which will be used by sparse irq.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

irq_to_desc_alloc_cpu() has been renamed to irq_to_desc_alloc_node() in
-next, but as we can not presently enable SPARSE_IRQ without the early
irq_desc alloc patch, protect it with an ifdef until the interface has
settled and we are ready to enable it system-wide.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.

Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.

Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Do not go beyond ARRAY_SIZE of onchip_ops
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix clkfwk branch compile error in clock-sh7722.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is just a simple arch_probe_nr_irqs() stub that wraps to the
platform defined number of IRQs. This can be made gradually more
intelligent based on what we can infer from the INTC tables and so on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This hooks in irq_to_desc_alloc_cpu() to the necessary code paths in the
intc and ipr controller registration paths. As these are the primary call
paths for all SH CPUs, this alone will make all CPUs sparse IRQ ready.

There is the added benefit now that each CPU contains specific IPR and
INTC tables, so only the vectors with interrupt sources backing them will
ever see an irq_desc instantiation. This effectively packs irq_desc
down to match the CPU, rather than padding NR_IRQS out to cover the valid
vector range.

Boards with extra sources will still have to fiddle with the nr_irqs
setting, but they can continue doing so through the machvec as before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This converts a few places that were using the old irq_desc[] array over
to the shiny new irq_to_desc() helper. Preperatory work for sparse irq
support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This tidies up how the SR.IMASK bitmap is managed, using the bitmap API
directly instead. At the same time, tidy up the irq_chip conversion a
bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
  drm: Copy back ioctl data to userspace regardless of return code.
  drm: Round size of SHM maps to PAGE_SIZE

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: 64-bit: Fix system lockup.
  MIPS: IP28: Change to build with -mr10k-cache-barrier=store
  MIPS: IP22: Fix hang in power button interrupt handler
  MIPS: IP32: Fix hang on shutdown in power button interrupt handler.

* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
  [ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
  [ARM] 5517/1: integrator: don't put clock lookups in __initdata
  [ARM] 5518/1: versatile: don't put clock lookups in __initdata
  [ARM] mach-l7200: fix spelling of SYS_CLOCK_OFF
  [ARM] Double check memmap is actually valid with a memmap has unexpected holes V2
  [ARM] realview: fix broadcast tick support
  [ARM] realview: remove useless smp_cross_call_done()
  [ARM] smp: fix cpumask usage in ARM SMP code
  [ARM] 5513/1: Eurotech VIPER SBC: fix compilation error
  [ARM] 5509/1: ep93xx: clkdev enable UARTS
  ARM: OMAP2/3: Change omapfb to use clkdev for dispc and rfbi, v2
  ARM: OMAP3: Fix HW SAVEANDRESTORE shift define
  ARM: OMAP3: Fix number of GPIO lines for 34xx
  [ARM] S3C: Do not set clk->owner field if unset
  [ARM] S3C2410: mach-bast.c registering i2c data too early
  [ARM] S3C24XX: Fix unused code warning in arch/arm/plat-s3c24xx/dma.c
  [ARM] S3C64XX: fix GPIO debug
  [ARM] S3C64XX: GPIO include cleanup
  [ARM] nwfpe: fix 'floatx80_is_nan' sparse warning
  [ARM] nwfpe: Add decleration for ExtendedCPDO
  ...

The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.

Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>