ARM: OMAP: USB peripheral support on H4

H4 has two peripheral ports, one for "download" and one for OTG.
The one to use is selected through Kconfig.

Also removes some bad whitespace from isp1301_omap.c

NOTE:  not yet working; I suspect there's a clock still turned off
or something like that, since neither port responds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

arch/arm/mach-omap2/Kconfig

@@ -49,6 +49,27 @@ config MACH_OMAP_H4_TUSB
 	  Be sure to select OTG mode operation, not host-only or
 	  peripheral-only.
 
+config MACH_OMAP_H4_OTG
+	bool "Use USB OTG connector, not device connector (S1.10)"
+	depends on MACH_OMAP_H4
+	help
+	  Set this if you've set S1.10 (on the mainboard) to use the
+	  Mini-AB (OTG) connector and OTG transceiver with the USB0
+	  port, instead of the Mini-B ("download") connector with its
+	  non-OTG transceiver.
+
+	  Note that the "download" connector can be used to bootstrap
+	  the system from the OMAP mask ROM.  Also, since this is a
+	  development platform, you can also force the OTG port into
+	  a non-OTG operational mode.
+
+config MACH_OMAP2_H4_USB1
+	bool "Use USB1 port, not UART2 (S3.3)"
+	depends on MACH_OMAP_H4
+	help
+	  Set this if you've set SW3.3 (on the CPU card) so that the
+	  expansion connectors receive USB1 signals instead of UART2.
+
 config MACH_OMAP_APOLLON
 	bool "OMAP 2420 Apollon board"
 	depends on ARCH_OMAP2 && ARCH_OMAP24XX

arch/arm/mach-omap2/board-h4.c

@@ -362,7 +362,11 @@ static void __init omap_h4_init_irq(void)
 }
 
 static struct omap_uart_config h4_uart_config __initdata = {
+#ifdef	CONFIG_MACH_OMAP2_H4_USB1
+	.enabled_uarts = ((1 << 0) | (1 << 1)),
+#else
 	.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+#endif
 };
 
 static struct omap_mmc_config h4_mmc_config __initdata = {
@@ -379,10 +383,44 @@ static struct omap_lcd_config h4_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
 
+static struct omap_usb_config h4_usb_config __initdata = {
+#ifdef	CONFIG_MACH_OMAP2_H4_USB1
+	/* NOTE:  usb1 could also be used with 3 wire signaling */
+	.pins[1]	= 4,
+#endif
+
+#ifdef	CONFIG_MACH_OMAP_H4_OTG
+	/* S1.10 ON -- USB OTG port
+	 * usb0 switched to Mini-AB port and isp1301 transceiver;
+	 * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging
+	 */
+	.otg		= 1,
+	.pins[0]	= 4,
+#ifdef	CONFIG_USB_GADGET_OMAP
+	/* use OTG cable, or standard A-to-MiniB */
+	.hmc_mode	= 0x14,	/* 0:dev/otg 1:host 2:disable */
+#elif	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	/* use OTG cable, or NONSTANDARD (B-to-MiniB) */
+	.hmc_mode	= 0x11,	/* 0:host 1:host 2:disable */
+#endif	/* XX */
+
+#else
+	/* S1.10 OFF -- usb "download port"
+	 * usb0 switched to Mini-B port and isp1105 transceiver;
+	 * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging
+	 */
+	.register_dev	= 1,
+	.pins[0]	= 3,
+//	.hmc_mode	= 0x14,	/* 0:dev 1:host 2:disable */
+	.hmc_mode	= 0x00,	/* 0:dev|otg 1:disable 2:disable */
+#endif
+};
+
 static struct omap_board_config_kernel h4_config[] = {
 	{ OMAP_TAG_UART,	&h4_uart_config },
 	{ OMAP_TAG_MMC,		&h4_mmc_config },
 	{ OMAP_TAG_LCD,		&h4_lcd_config },
+	{ OMAP_TAG_USB,		&h4_usb_config },
 };
 
 #ifdef	CONFIG_MACH_OMAP_H4_TUSB
@@ -471,6 +509,14 @@ static void __init omap_h4_init(void)
 	}
 #endif
 
+#ifdef	CONFIG_MACH_OMAP2_H4_USB1
+	/* S3.3 controls whether these pins are for UART2 or USB1 */
+	omap_cfg_reg(N14_24XX_USB1_SE0);
+	omap_cfg_reg(P15_24XX_USB1_DAT);
+	omap_cfg_reg(W20_24XX_USB1_TXEN);
+	omap_cfg_reg(V19_24XX_USB1_RCV);
+#endif
+
 	platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
 	omap_board_config = h4_config;
 	omap_board_config_size = ARRAY_SIZE(h4_config);

drivers/i2c/chips/isp1301_omap.c

@@ -1245,6 +1245,9 @@ static int isp1301_detach_client(struct i2c_client *i2c)
 	if (machine_is_omap_h3())
 		omap_free_gpio(14);
 
+	if (machine_is_omap_h4())
+		omap_free_gpio(125);
+
 	isp->timer.data = 0;
 	set_bit(WORK_STOP, &isp->todo);
 	del_timer_sync(&isp->timer);
@@ -1323,6 +1326,7 @@ isp1301_set_host(struct otg_transceiver *otg, struct usb_bus *host)
 
 	power_up(isp);
 
+// XXX h4 too?
 	if (machine_is_omap_h2() || machine_is_omap_h3())
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
 
@@ -1386,6 +1390,7 @@ isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget)
 	power_up(isp);
 	isp->otg.state = OTG_STATE_B_IDLE;
 
+// XXX h4 too?
 	if (machine_is_omap_h2() || machine_is_omap_h3())
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
 
@@ -1589,6 +1594,7 @@ fail1:
 	}
 #endif
 
+// XXX h4 too?
 	if (machine_is_omap_h2() || machine_is_omap_h3()) {
 		/* full speed signaling by default */
 		isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1,
@@ -1615,6 +1621,15 @@ fail1:
 		isp->irq_type = SA_TRIGGER_FALLING;
 	}
 
+	if (machine_is_omap_h4()) {
+		/* IRQ wired at P14 */
+		omap_cfg_reg(P14_24XX_GPIO125);
+		isp->irq = OMAP_GPIO_IRQ(125);
+		omap_request_gpio(125);
+		omap_set_gpio_direction(125, 1);
+		isp->irq_type = IRQF_TRIGGER_LOW;
+	}
+
 	status = request_irq(isp->irq, isp1301_irq,
 			isp->irq_type, DRIVER_NAME, isp);
 	if (status < 0) {

drivers/usb/gadget/Kconfig

@@ -168,7 +168,7 @@ config USB_GADGET_MUSB_HDRC
 config USB_GADGET_OMAP
 	boolean "OMAP USB Device Controller"
 	depends on ARCH_OMAP
-	select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
+	select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG
 	help
 	   Many Texas Instruments OMAP processors have flexible full
 	   speed USB device controllers, with support for up to 30