Merge branch 'e1000-fixes' of git://198.78.49.142/~jbrandeb/linux-2.6

Documentation/networking/e100.txt

 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
-November 17, 2004
-
+November 15, 2005
 
 Contents
 ========
 
 - In This Release
 - Identifying Your Adapter
+- Building and Installation
 - Driver Configuration Parameters
 - Additional Configurations
+- Known Issues
 - Support
 
 
@@ -18,7 +19,19 @@ In This Release
 ===============
 
 This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
-Adapters, version 3.3.x.  This driver supports 2.4.x and 2.6.x kernels. 
+Adapters. This driver includes support for Itanium(R)2-based systems.
+
+For questions related to hardware requirements, refer to the documentation
+supplied with your Intel PRO/100 adapter.
+
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
 
 Identifying Your Adapter
 ========================
@@ -43,18 +56,18 @@ unless otherwise noted.
 Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
    structure that describes a receive buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to write
-   data from the controller to host memory. In the 3.0.x driver the valid
-   range for this parameter is 64-256. The default value is 64. This parameter 
-   can be changed using the command 
+   data from the controller to host memory. In the 3.x.x driver the valid range
+   for this parameter is 64-256. The default value is 64. This parameter can be
+   changed using the command:
 
    ethtool -G eth? rx n, where n is the number of desired rx descriptors.
 
-Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a
-   data structure that describes a transmit buffer and its attributes to the
-   network controller. The data in the descriptor is used by the controller to 
-   read data from the host memory to the controller. In the 3.0.x driver the 
-   valid range for this parameter is 64-256. The default value is 64. This 
-   parameter can be changed using the command 
+Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
+   structure that describes a transmit buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to read
+   data from the host memory to the controller. In the 3.x.x driver the valid
+   range for this parameter is 64-256. The default value is 64. This parameter
+   can be changed using the command:
 
    ethtool -G eth? tx n, where n is the number of desired tx descriptors.
 
@@ -68,10 +81,11 @@ Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
 
 Event Log Message Level:  The driver uses the message level flag to log events
    to syslog. The message level can be set at driver load time. It can also be
-   set using the command
+   set using the command:
 
    ethtool -s eth? msglvl n
 
+
 Additional Configurations
 =========================
 
@@ -80,16 +94,16 @@ Additional Configurations
 
   Configuring a network driver to load properly when the system is started is
   distribution dependent. Typically, the configuration process involves adding
-  an alias line to /etc/modules.conf as well as editing other system startup 
-  scripts and/or configuration files.  Many popular Linux distributions ship 
-  with tools to make these changes for you. To learn the proper way to 
-  configure a network device for your system, refer to your distribution 
-  documentation. If during this process you are asked for the driver or module 
-  name, the name for the Linux Base Driver for the Intel PRO/100 Family of 
-  Adapters is e100.
+  an alias line to /etc/modules.conf or /etc/modprobe.conf as well as editing
+  other system startup scripts and/or configuration files.  Many popular Linux
+  distributions ship with tools to make these changes for you. To learn the
+  proper way to configure a network device for your system, refer to your
+  distribution documentation.  If during this process you are asked for the
+  driver or module name, the name for the Linux Base Driver for the Intel
+  PRO/100 Family of Adapters is e100.
 
   As an example, if you install the e100 driver for two PRO/100 adapters
-  (eth0 and eth1), add the following to modules.conf:
+  (eth0 and eth1), add the following to modules.conf or modprobe.conf:
 
        alias eth0 e100
        alias eth1 e100
@@ -107,6 +121,7 @@ Additional Configurations
 
   NOTE: This setting is not saved across reboots.
 
+
   Ethtool
   -------
 
@@ -114,29 +129,27 @@ Additional Configurations
   diagnostics, as well as displaying statistical information.  Ethtool
   version 1.6 or later is required for this functionality.
 
-  The latest release of ethtool can be found at:
-  http://sf.net/projects/gkernel.  
-
-  NOTE: This driver uses mii support from the kernel. As a result, when 
-  there is no link, ethtool will report speed/duplex to be 10/half.
+  The latest release of ethtool can be found from
+  http://sourceforge.net/projects/gkernel.
 
   NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
   for a more complete ethtool feature set can be enabled by upgrading
   ethtool to ethtool-1.8.1.
 
+
   Enabling Wake on LAN* (WoL)
   ---------------------------
   WoL is provided through the Ethtool* utility. Ethtool is included with Red
   Hat* 8.0. For other Linux distributions, download and install Ethtool from
   the following website: http://sourceforge.net/projects/gkernel.
 
-  For instructions on enabling WoL with Ethtool, refer to the Ethtool man
-  page.
+  For instructions on enabling WoL with Ethtool, refer to the Ethtool man page.
 
   WoL will be enabled on the system during the next shut down or reboot. For
   this driver version, in order to enable WoL, the e100 driver must be
   loaded when shutting down or rebooting the system.
 
+
   NAPI
   ----
 
@@ -144,6 +157,25 @@ Additional Configurations
 
   See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
 
+  Multiple Interfaces on Same Ethernet Broadcast Network
+  ------------------------------------------------------
+
+  Due to the default ARP behavior on Linux, it is not possible to have
+  one system on two IP networks in the same Ethernet broadcast domain
+  (non-partitioned switch) behave as expected. All Ethernet interfaces
+  will respond to IP traffic for any IP address assigned to the system.
+  This results in unbalanced receive traffic.
+
+  If you have multiple interfaces in a server, either turn on ARP
+  filtering by
+
+  (1) entering: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+      (this only works if your kernel's version is higher than 2.4.5), or
+
+  (2) installing the interfaces in separate broadcast domains (either
+      in different switches or in a switch partitioned to VLANs).
+
+
 Support
 =======
 
@@ -151,9 +183,13 @@ For general information, go to the Intel support website at:
 
     http://support.intel.com
 
+    or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
 If an issue is identified with the released source code on the supported
-kernel with a supported adapter, email the specific information related to 
-the issue to linux.nics@intel.com.
+kernel with a supported adapter, email the specific information related to the
+issue to e1000-devel@lists.sourceforge.net.
 
 
 License
@@ -162,9 +198,9 @@ License
 This software program is released under the terms of a license agreement
 between you ('Licensee') and Intel. Do not use or load this software or any
 associated materials (collectively, the 'Software') until you have carefully
-read the full terms and conditions of the LICENSE located in this software 
+read the full terms and conditions of the file COPYING located in this software
 package. By loading or using the Software, you agree to the terms of this
-Agreement. If you do not agree with the terms of this Agreement, do not 
-install or use the Software.
+Agreement. If you do not agree with the terms of this Agreement, do not install
+or use the Software.
 
 * Other names and brands may be claimed as the property of others.

Documentation/networking/e1000.txt

 Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
 ===============================================================
 
-November 17, 2004
+November 15, 2005
 
 
 Contents
@@ -20,13 +20,27 @@ In This Release
 ===============
 
 This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters, version 5.x.x.  
+of Adapters.  This driver includes support for Itanium(R)2-based systems.
 
 For questions related to hardware requirements, refer to the documentation
 supplied with your Intel PRO/1000 adapter. All hardware requirements listed
 apply to use with Linux.
 
-Native VLANs are now available with supported kernels.
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
+The driver information previously displayed in the /proc filesystem is not
+supported in this release.  Alternatively, you can use ethtool (version 1.6
+or later), lspci, and ifconfig to obtain the same information.
+
+Instructions on updating ethtool can be found in the section "Additional
+Configurations" later in this document.
+
 
 Identifying Your Adapter
 ========================
@@ -42,12 +56,12 @@ networking link on the left to search for your adapter:
 
     http://downloadfinder.intel.com/scripts-df/support_intel.asp
 
-Command Line Parameters
-=======================
 
-If the driver is built as a module, the  following optional parameters are 
-used by entering them on the command line with the modprobe or insmod command
-using this syntax:
+Command Line Parameters =======================
+
+If the driver is built as a module, the  following optional parameters
+are used by entering them on the command line with the modprobe or insmod
+command using this syntax:
 
      modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
 
@@ -57,217 +71,265 @@ For example, with two PRO/1000 PCI adapters, entering:
 
      insmod e1000 TxDescriptors=80,128
 
-loads the e1000 driver with 80 TX descriptors for the first adapter and 128 TX 
-descriptors for the second adapter.
+loads the e1000 driver with 80 TX descriptors for the first adapter and 128
+TX descriptors for the second adapter.
 
 The default value for each parameter is generally the recommended setting,
-unless otherwise noted. Also, if the driver is statically built into the
-kernel, the driver is loaded with the default values for all the parameters.
-Ethtool can be used to change some of the parameters at runtime.
+unless otherwise noted.
 
-    NOTES: For more information about the AutoNeg, Duplex, and Speed
+NOTES:  For more information about the AutoNeg, Duplex, and Speed
         parameters, see the "Speed and Duplex Configuration" section in
         this document.
 
-           For more information about the InterruptThrottleRate, RxIntDelay, 
-           TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay parameters, see the 
-           application note at:
+        For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
         http://www.intel.com/design/network/applnots/ap450.htm
 
-           A descriptor describes a data buffer and attributes related to the 
-           data buffer. This information is accessed by the hardware.
+        A descriptor describes a data buffer and attributes related to
+        the data buffer. This information is accessed by the hardware.
 
-AutoNeg (adapters using copper connections only)
+
+AutoNeg
+-------
+(Supported only on adapters with copper connections)
 Valid Range:   0x01-0x0F, 0x20-0x2F
 Default Value: 0x2F
-    This parameter is a bit mask that specifies which speed and duplex
-    settings the board advertises. When this parameter is used, the Speed and
-    Duplex parameters must not be specified.
-    NOTE: Refer to the Speed and Duplex section of this readme for more 
+
+This parameter is a bit mask that specifies which speed and duplex
+settings the board advertises. When this parameter is used, the Speed
+and Duplex parameters must not be specified.
+
+NOTE:  Refer to the Speed and Duplex section of this readme for more
        information on the AutoNeg parameter.
 
-Duplex (adapters using copper connections only)
+
+Duplex
+------
+(Supported only on adapters with copper connections)
 Valid Range:   0-2 (0=auto-negotiate, 1=half, 2=full)
 Default Value: 0
-    Defines the direction in which data is allowed to flow. Can be either one 
-    or two-directional. If both Duplex and the link partner are set to auto-
-    negotiate, the board auto-detects the correct duplex. If the link partner
-    is forced (either full or half), Duplex defaults to half-duplex.
+
+Defines the direction in which data is allowed to flow. Can be either
+one or two-directional. If both Duplex and the link partner are set to
+auto-negotiate, the board auto-detects the correct duplex. If the link
+partner is forced (either full or half), Duplex defaults to half-duplex.
+
 
 FlowControl
+----------
 Valid Range:   0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
-Default: Read flow control settings from the EEPROM
-    This parameter controls the automatic generation(Tx) and response(Rx) to 
-    Ethernet PAUSE frames.
+Default Value: Reads flow control settings from the EEPROM
+
+This parameter controls the automatic generation(Tx) and response(Rx)
+to Ethernet PAUSE frames.
+
 
 InterruptThrottleRate
+---------------------
+(not supported on Intel 82542, 82543 or 82544-based adapters)
 Valid Range:   100-100000 (0=off, 1=dynamic)
 Default Value: 8000
-    This value represents the maximum number of interrupts per second the 
-    controller generates. InterruptThrottleRate is another setting used in 
-    interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust 
-    InterruptThrottleRate based on the current traffic load.
-Un-supported Adapters: InterruptThrottleRate is NOT supported by 82542, 82543
-    or 82544-based adapters.
-
-    NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and 
+
+This value represents the maximum number of interrupts per second the
+controller generates. InterruptThrottleRate is another setting used in
+interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
+InterruptThrottleRate based on the current traffic load.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
        RxAbsIntDelay parameters. In other words, minimizing the receive
        and/or transmit absolute delays does not force the controller to
        generate more interrupts than what the Interrupt Throttle Rate
        allows.
-    CAUTION: If you are using the Intel PRO/1000 CT Network Connection 
+
+CAUTION:  If you are using the Intel PRO/1000 CT Network Connection
           (controller 82547), setting InterruptThrottleRate to a value
-             greater than 75,000, may hang (stop transmitting) adapters under 
-             certain network conditions. If this occurs a NETDEV WATCHDOG 
-             message is logged in the system event log. In addition, the 
-             controller is automatically reset, restoring the network 
-             connection. To eliminate the potential for the hang, ensure 
-             that InterruptThrottleRate is set no greater than 75,000 and is 
-             not set to 0.
-    NOTE: When e1000 is loaded with default settings and multiple adapters are 
-          in use simultaneously, the CPU utilization may increase non-linearly. 
-          In order to limit the CPU utilization without impacting the overall 
-          throughput, we recommend that you load the driver as follows:
+          greater than 75,000, may hang (stop transmitting) adapters
+          under certain network conditions. If this occurs a NETDEV
+          WATCHDOG message is logged in the system event log. In
+          addition, the controller is automatically reset, restoring
+          the network connection. To eliminate the potential for the
+          hang, ensure that InterruptThrottleRate is set no greater
+          than 75,000 and is not set to 0.
+
+NOTE:  When e1000 is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly. In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
 
            insmod e1000.o InterruptThrottleRate=3000,3000,3000
 
-          This sets the InterruptThrottleRate to 3000 interrupts/sec for the 
-          first, second, and third instances of the driver. The range of 2000 to 
-          3000 interrupts per second works on a majority of systems and is a 
-          good starting point, but the optimal value will be platform-specific. 
-          If CPU utilization is not a concern, use RX_POLLING (NAPI) and default 
-          driver settings.
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver. The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific. If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
 
 RxDescriptors
+-------------
 Valid Range:   80-256 for 82542 and 82543-based adapters
                80-4096 for all other supported adapters
 Default Value: 256
-    This value is the number of receive descriptors allocated by the driver. 
-    Increasing this value allows the driver to buffer more incoming packets. 
-    Each descriptor is 16 bytes.  A receive buffer is allocated for each
-    descriptor and can either be 2048 or 4096 bytes long, depending on the MTU 
-
-    setting. An incoming packet can span one or more receive descriptors. 
-    The maximum MTU size is 16110.
-
-    NOTE: MTU designates the frame size. It only needs to be set for Jumbo 
-          Frames.
-    NOTE: Depending on the available system resources, the request for a
-    higher number of receive descriptors may be denied.  In this case,
-    use a lower number.
+
+This value specifies the number of receive descriptors allocated by the
+driver. Increasing this value allows the driver to buffer more incoming
+packets.  Each descriptor is 16 bytes.  A receive buffer is also
+allocated for each descriptor and is 2048.
+
 
 RxIntDelay
+----------
 Valid Range:   0-65535 (0=off)
 Default Value: 0
-    This value delays the generation of receive interrupts in units of 1.024 
-    microseconds.  Receive interrupt reduction can improve CPU efficiency if 
-    properly tuned for specific network traffic. Increasing this value adds 
-    extra latency to frame reception and can end up decreasing the throughput 
-    of TCP traffic. If the system is reporting dropped receives, this value 
-    may be set too high, causing the driver to run out of available receive 
-    descriptors.
-
-    CAUTION: When setting RxIntDelay to a value other than 0, adapters may 
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic. Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic. If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
           hang (stop transmitting) under certain network conditions. If
           this occurs a NETDEV WATCHDOG message is logged in the system
           event log. In addition, the controller is automatically reset,
-             restoring the network connection. To eliminate the potential for
-             the hang ensure that RxIntDelay is set to 0.
+          restoring the network connection. To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
 
-RxAbsIntDelay (82540, 82545 and later adapters only)
+RxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
 Valid Range:   0-65535 (0=off)
 Default Value: 128
-    This value, in units of 1.024 microseconds, limits the delay in which a 
-    receive interrupt is generated. Useful only if RxIntDelay is non-zero, 
-    this value ensures that an interrupt is generated after the initial 
-    packet is received within the set amount of time.  Proper tuning,
-    along with RxIntDelay, may improve traffic throughput in specific network
-    conditions.
-
-Speed (adapters using copper connections only)
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated. Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+
+Speed
+-----
+(This parameter is supported only on adapters with copper connections.)
 Valid Settings: 0, 10, 100, 1000
 Default Value:  0 (auto-negotiate at all supported speeds)
-    Speed forces the line speed to the specified value in megabits per second
-    (Mbps). If this parameter is not specified or is set to 0 and the link 
-    partner is set to auto-negotiate, the board will auto-detect the correct 
-    speed. Duplex should also be set when Speed is set to either 10 or 100.
+
+Speed forces the line speed to the specified value in megabits per second
+(Mbps). If this parameter is not specified or is set to 0 and the link
+partner is set to auto-negotiate, the board will auto-detect the correct
+speed. Duplex should also be set when Speed is set to either 10 or 100.
+
 
 TxDescriptors
+-------------
 Valid Range:   80-256 for 82542 and 82543-based adapters
                80-4096 for all other supported adapters
 Default Value: 256
-    This value is the number of transmit descriptors allocated by the driver.
-    Increasing this value allows the driver to queue more transmits. Each 
-    descriptor is 16 bytes.
 
-    NOTE: Depending on the available system resources, the request for a
+This value is the number of transmit descriptors allocated by the driver.
+Increasing this value allows the driver to queue more transmits. Each
+descriptor is 16 bytes.
+
+NOTE:  Depending on the available system resources, the request for a
        higher number of transmit descriptors may be denied.  In this case,
        use a lower number.
 
+
 TxIntDelay
+----------
 Valid Range:   0-65535 (0=off)
 Default Value: 64
-    This value delays the generation of transmit interrupts in units of 
-    1.024 microseconds. Transmit interrupt reduction can improve CPU
-    efficiency if properly tuned for specific network traffic. If the
-    system is reporting dropped transmits, this value may be set too high
-    causing the driver to run out of available transmit descriptors.
 
-TxAbsIntDelay (82540, 82545 and later adapters only)
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds. Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic. If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+
+TxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
 Valid Range:   0-65535 (0=off)
 Default Value: 64
-    This value, in units of 1.024 microseconds, limits the delay in which a 
-    transmit interrupt is generated. Useful only if TxIntDelay is non-zero, 
-    this value ensures that an interrupt is generated after the initial 
-    packet is sent on the wire within the set amount of time.  Proper tuning,
-    along with TxIntDelay, may improve traffic throughput in specific 
-    network conditions.
-
-XsumRX (not available on the 82542-based adapter)
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+XsumRX
+------
+(This parameter is NOT supported on the 82542-based adapter.)
 Valid Range:   0-1
 Default Value: 1
-    A value of '1' indicates that the driver should enable IP checksum
-    offload for received packets (both UDP and TCP) to the adapter hardware.
+
+A value of '1' indicates that the driver should enable IP checksum
+offload for received packets (both UDP and TCP) to the adapter hardware.
+
 
 Speed and Duplex Configuration
 ==============================
 
-Three keywords are used to control the speed and duplex configuration. These 
-keywords are Speed, Duplex, and AutoNeg.
+Three keywords are used to control the speed and duplex configuration.
+These keywords are Speed, Duplex, and AutoNeg.
 
 If the board uses a fiber interface, these keywords are ignored, and the
 fiber interface board only links at 1000 Mbps full-duplex.
 
 For copper-based boards, the keywords interact as follows:
 
-  The default operation is auto-negotiate. The board advertises all supported
-  speed and duplex combinations, and it links at the highest common speed and
-  duplex mode IF the link partner is set to auto-negotiate.
+  The default operation is auto-negotiate. The board advertises all
+  supported speed and duplex combinations, and it links at the highest
+  common speed and duplex mode IF the link partner is set to auto-negotiate.
 
-  If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps is
-  advertised (The 1000BaseT spec requires auto-negotiation.)
+  If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
+  is advertised (The 1000BaseT spec requires auto-negotiation.)
 
   If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
-  negotiation is disabled, and the AutoNeg parameter is ignored. Partner SHOULD
-  also be forced.
+  negotiation is disabled, and the AutoNeg parameter is ignored. Partner
+  SHOULD also be forced.
 
-The AutoNeg parameter is used when more control is required over the auto-
-negotiation process. When this parameter is used, Speed and Duplex parameters 
-must not be specified. The following table describes supported values for the 
-AutoNeg parameter:
+The AutoNeg parameter is used when more control is required over the
+auto-negotiation process.  It should be used when you wish to control which
+speed and duplex combinations are advertised during the auto-negotiation
+process.
 
-Speed (Mbps)   		 1000      100    100    10     10
+The parameter may be specified as either a decimal or hexidecimal value as
+determined by the bitmap below.
+
+Bit position   7      6      5       4       3      2      1       0
+Decimal Value  128    64     32      16      8      4      2       1
+Hex value      80     40     20      10      8      4      2       1
+Speed (Mbps)   N/A    N/A    1000    N/A     100    100    10      10
 Duplex                       Full            Full   Half   Full    Half
-Value (in base 16)       0x20      0x08   0x04   0x02   0x01
 
-Example: insmod e1000 AutoNeg=0x03, loads e1000 and specifies (10 full duplex, 
-10 half duplex) for negotiation with the peer.
+Some examples of using AutoNeg:
+
+  modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
+  modprobe e1000 AutoNeg=1 (Same as above)
+  modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full)
+  modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full)
+  modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half)
+  modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100
+  Half)
+  modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full)
+  modprobe e1000 AutoNeg=32 (Same as above)
+
+Note that when this parameter is used, Speed and Duplex must not be specified.
 
-Note that setting AutoNeg does not guarantee that the board will link at the 
-highest specified speed or duplex mode, but the board will link at the 
-highest possible speed/duplex of the link partner IF the link partner is also
-set to auto-negotiate. If the link partner is forced speed/duplex, the 
-adapter MUST be forced to the same speed/duplex.
+If the link partner is forced to a specific speed and duplex, then this
+parameter should not be used.  Instead, use the Speed and Duplex parameters
+previously mentioned to force the adapter to the same speed and duplex.
 
 
 Additional Configurations
@@ -276,19 +338,19 @@ Additional Configurations
   Configuring the Driver on Different Distributions
   -------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is
-  distribution dependent. Typically, the configuration process involves adding
-  an alias line to /etc/modules.conf as well as editing other system startup 
-  scripts and/or configuration files. Many popular Linux distributions ship 
-  with tools to make these changes for you. To learn the proper way to 
-  configure a network device for your system, refer to your distribution 
-  documentation. If during this process you are asked for the driver or module 
-  name, the name for the Linux Base Driver for the Intel PRO/1000 Family of 
-  Adapters is e1000.
+  Configuring a network driver to load properly when the system is started
+  is distribution dependent. Typically, the configuration process involves
+  adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
+  as editing other system startup scripts and/or configuration files. Many
+  popular Linux distributions ship with tools to make these changes for you.
+  To learn the proper way to configure a network device for your system,
+  refer to your distribution documentation. If during this process you are
+  asked for the driver or module name, the name for the Linux Base Driver
+  for the Intel PRO/1000 Family of Adapters is e1000.
 
   As an example, if you install the e1000 driver for two PRO/1000 adapters
-  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add the 
-  following to modules.conf:
+  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
+  the following to modules.conf or or modprobe.conf:
 
        alias eth0 e1000
        alias eth1 e1000
@@ -298,8 +360,8 @@ Additional Configurations
   ---------------------
 
   Link messages will not be displayed to the console if the distribution is
-  restricting system messages. In order to see network driver link messages on 
-  your console, set dmesg to eight by entering the following:
+  restricting system messages. In order to see network driver link messages
+  on your console, set dmesg to eight by entering the following:
 
        dmesg -n 8
 
@@ -308,22 +370,42 @@ Additional Configurations
   Jumbo Frames
   ------------
 
-  The driver supports Jumbo Frames for all adapters except 82542-based 
-  adapters. Jumbo Frames support is enabled by changing the MTU to a value 
-  larger than the default of 1500. Use the ifconfig command to increase the 
-  MTU size. For example:
+  The driver supports Jumbo Frames for all adapters except 82542 and
+  82573-based adapters. Jumbo Frames support is enabled by changing the
+  MTU to a value larger than the default of 1500. Use the ifconfig command
+  to increase the MTU size. For example:
 
-        ifconfig ethx mtu 9000 up
+       ifconfig eth<x> mtu 9000 up
 
-  The maximum MTU setting for Jumbo Frames is 16110. This value coincides 
-  with the maximum Jumbo Frames size of 16128.
+  This setting is not saved across reboots.  It can be made permanent if
+  you add:
 
-  NOTE: Jumbo Frames are supported at 1000 Mbps only. Using Jumbo Frames at 
-  10 or 100 Mbps may result in poor performance or loss of link.
+       MTU=9000
 
+   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+   applies to the Red Hat distributions; other distributions may store this
+   setting in a different location.
+
+  Notes:
+
+  - To enable Jumbo Frames, increase the MTU size on the interface beyond
+    1500.
+  - The maximum MTU setting for Jumbo Frames is 16110. This value coincides
+    with the maximum Jumbo Frames size of 16128.
+  - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
+    loss of link.
+  - Some Intel gigabit adapters that support Jumbo Frames have a frame size
+    limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
+    The adapters with this limitation are based on the Intel 82571EB and
+    82572EI controllers, which correspond to these product names:
+     Intel® PRO/1000 PT Dual Port Server Adapter
+     Intel® PRO/1000 PF Dual Port Server Adapter
+     Intel® PRO/1000 PT Server Adapter
+     Intel® PRO/1000 PT Desktop Adapter
+     Intel® PRO/1000 PF Server Adapter
+
+  - The Intel PRO/1000 PM Network Connection does not support jumbo frames.
 
-  NOTE: MTU designates the frame size. To enable Jumbo Frames, increase the
-  MTU size on the interface beyond 1500.
 
   Ethtool
   -------
@@ -333,7 +415,7 @@ Additional Configurations
   version 1.6 or later is required for this functionality.
 
   The latest release of ethtool can be found from
-  http://sf.net/projects/gkernel.  
+  http://sourceforge.net/projects/gkernel.
 
   NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
   for a more complete ethtool feature set can be enabled by upgrading
@@ -358,7 +440,16 @@ Additional Configurations
   ----
 
   NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled
-  or disabled based on the configuration of the kernel. 
+  or disabled based on the configuration of the kernel. To override
+  the default, use the following compile-time flags.
+
+  To enable NAPI, compile the driver module, passing in a configuration option:
+
+       make CFLAGS_EXTRA=-DE1000_NAPI install
+
+  To disable NAPI, compile the driver module, passing in a configuration option:
+
+       make CFLAGS_EXTRA=-DE1000_NO_NAPI install
 
   See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
 
@@ -370,9 +461,84 @@ Known Issues
   -------------------------------
 
   Memory allocation failures have been observed on Linux systems with 64 MB
-  of RAM or less that are running Jumbo Frames. If you are using Jumbo Frames,
-  your system may require more than the advertised minimum requirement of 64 MB
-  of system memory.
+  of RAM or less that are running Jumbo Frames. If you are using Jumbo
+  Frames, your system may require more than the advertised minimum
+  requirement of 64 MB of system memory.
+
+  Performance Degradation with Jumbo Frames
+  -----------------------------------------
+
+  Degradation in throughput performance may be observed in some Jumbo frames
+  environments. If this is observed, increasing the application's socket
+  buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
+  may help. See the specific application manual and
+  /usr/src/linux*/Documentation/
+  networking/ip-sysctl.txt for more details.
+
+  Jumbo frames on Foundry BigIron 8000 switch
+  -------------------------------------------
+  There is a known issue using Jumbo frames when connected to a Foundry
+  BigIron 8000 switch. This is a 3rd party limitation. If you experience
+  loss of packets, lower the MTU size.
+
+  Multiple Interfaces on Same Ethernet Broadcast Network
+  ------------------------------------------------------
+
+  Due to the default ARP behavior on Linux, it is not possible to have
+  one system on two IP networks in the same Ethernet broadcast domain
+  (non-partitioned switch) behave as expected. All Ethernet interfaces
+  will respond to IP traffic for any IP address assigned to the system.
+  This results in unbalanced receive traffic.
+
+  If you have multiple interfaces in a server, either turn on ARP
+  filtering by entering:
+
+      echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+  (this only works if your kernel's version is higher than 2.4.5),
+
+  NOTE: This setting is not saved across reboots. The configuration
+  change can be made permanent by adding the line:
+      net.ipv4.conf.all.arp_filter = 1
+  to the file /etc/sysctl.conf
+
+        or,
+
+  install the interfaces in separate broadcast domains (either in
+  different switches or in a switch partitioned to VLANs).
+
+  82541/82547 can't link or are slow to link with some link partners
+  -----------------------------------------------------------------
+
+  There is a known compatibility issue with 82541/82547 and some
+  low-end switches where the link will not be established, or will
+  be slow to establish.  In particular, these switches are known to
+  be incompatible with 82541/82547:
+
+      Planex FXG-08TE
+      I-O Data ETG-SH8
+
+  To workaround this issue, the driver can be compiled with an override
+  of the PHY's master/slave setting.  Forcing master or forcing slave
+  mode will improve time-to-link.
+
+      # make EXTRA_CFLAGS=-DE1000_MASTER_SLAVE=<n>
+
+  Where <n> is:
+
+      0 = Hardware default
+      1 = Master mode
+      2 = Slave mode
+      3 = Auto master/slave
+
+  Disable rx flow control with ethtool
+  ------------------------------------
+
+  In order to disable receive flow control using ethtool, you must turn
+  off auto-negotiation on the same command line.
+
+  For example:
+
+     ethtool -A eth? autoneg off rx off
 
 
 Support
@@ -382,9 +548,13 @@ For general information, go to the Intel support website at:
 
     http://support.intel.com
 
+    or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
 If an issue is identified with the released source code on the supported
-kernel with a supported adapter, email the specific information related to 
-the issue to linux.nics@intel.com.
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sourceforge.net
 
 
 License
@@ -393,7 +563,7 @@ License
 This software program is released under the terms of a license agreement
 between you ('Licensee') and Intel. Do not use or load this software or any
 associated materials (collectively, the 'Software') until you have carefully
-read the full terms and conditions of the LICENSE located in this software 
+read the full terms and conditions of the file COPYING located in this software
 package. By loading or using the Software, you agree to the terms of this
 Agreement. If you do not agree with the terms of this Agreement, do not
 install or use the Software.

MAINTAINERS

@@ -1349,10 +1349,10 @@ S:	Maintained
 INTEL PRO/100 ETHERNET SUPPORT
 P:	John Ronciak
 M:	john.ronciak@intel.com
-P:	Ganesh Venkatesan
-M:	ganesh.venkatesan@intel.com
 P:	Jesse Brandeburg
 M:	jesse.brandeburg@intel.com
+P:	Jeff Kirsher
+M:	jeffrey.t.kirsher@intel.com
 W:	http://sourceforge.net/projects/e1000/
 S:	Supported
 
@@ -1361,18 +1361,22 @@ P:	Jeb Cramer
 M:	cramerj@intel.com
 P:	John Ronciak
 M:	john.ronciak@intel.com
-P:	Ganesh Venkatesan
-M:	ganesh.venkatesan@intel.com
+P:	Jesse Brandeburg
+M:	jesse.brandeburg@intel.com
+P:	Jeff Kirsher
+M:	jeffrey.t.kirsher@intel.com
 W:	http://sourceforge.net/projects/e1000/
 S:	Supported
 
 INTEL PRO/10GbE SUPPORT
+P:	Jeff Kirsher
+M:	jeffrey.t.kirsher@intel.com
 P:	Ayyappan Veeraiyan
 M:	ayyappan.veeraiyan@intel.com
-P:	Ganesh Venkatesan
-M:	ganesh.venkatesan@intel.com
 P:	John Ronciak
 M:	john.ronciak@intel.com
+P:	Jesse Brandeburg
+M:	jesse.brandeburg@intel.com
 W:	http://sourceforge.net/projects/e1000/
 S:	Supported