Commit b6e6d120 authored by Manuel Lauss's avatar Manuel Lauss Committed by Ralf Baechle

MIPS: Alchemy: get rid of superfluous UART definitions

Remove unused uart bit definitions and base macros.
Signed-off-by: default avatarManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 8402a158
......@@ -22,36 +22,34 @@
#define PORT(_base, _irq) \
{ \
.iobase = _base, \
.membase = (void __iomem *)_base,\
.mapbase = CPHYSADDR(_base), \
.mapbase = _base, \
.irq = _irq, \
.regshift = 2, \
.iotype = UPIO_AU, \
.flags = UPF_SKIP_TEST \
.flags = UPF_SKIP_TEST | UPF_IOREMAP \
}
static struct plat_serial8250_port au1x00_uart_data[] = {
#if defined(CONFIG_SERIAL_8250_AU1X00)
#if defined(CONFIG_SOC_AU1000)
PORT(UART0_ADDR, AU1000_UART0_INT),
PORT(UART1_ADDR, AU1000_UART1_INT),
PORT(UART2_ADDR, AU1000_UART2_INT),
PORT(UART3_ADDR, AU1000_UART3_INT),
PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
#elif defined(CONFIG_SOC_AU1500)
PORT(UART0_ADDR, AU1500_UART0_INT),
PORT(UART3_ADDR, AU1500_UART3_INT),
PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
#elif defined(CONFIG_SOC_AU1100)
PORT(UART0_ADDR, AU1100_UART0_INT),
PORT(UART1_ADDR, AU1100_UART1_INT),
PORT(UART3_ADDR, AU1100_UART3_INT),
PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
#elif defined(CONFIG_SOC_AU1550)
PORT(UART0_ADDR, AU1550_UART0_INT),
PORT(UART1_ADDR, AU1550_UART1_INT),
PORT(UART3_ADDR, AU1550_UART3_INT),
PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
#elif defined(CONFIG_SOC_AU1200)
PORT(UART0_ADDR, AU1200_UART0_INT),
PORT(UART1_ADDR, AU1200_UART1_INT),
PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
#endif
#endif /* CONFIG_SERIAL_8250_AU1X00 */
{ },
......
......@@ -916,8 +916,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1000
#define UART0_ADDR 0xB1100000
#define UART1_ADDR 0xB1200000
#define UART2_ADDR 0xB1300000
#define UART3_ADDR 0xB1400000
#define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */
......@@ -952,7 +950,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1100
#define UART0_ADDR 0xB1100000
#define UART1_ADDR 0xB1200000
#define UART3_ADDR 0xB1400000
#define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */
......@@ -966,8 +963,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1550
#define UART0_ADDR 0xB1100000
#define UART1_ADDR 0xB1200000
#define UART3_ADDR 0xB1400000
#define USB_OHCI_BASE 0x14020000 /* phys addr for ioremap */
#define USB_OHCI_LEN 0x00060000
......@@ -985,7 +980,6 @@ enum soc_au1200_ints {
#ifdef CONFIG_SOC_AU1200
#define UART0_ADDR 0xB1100000
#define UART1_ADDR 0xB1200000
#define USB_UOC_BASE 0x14020020
#define USB_UOC_LEN 0x20
......@@ -1262,14 +1256,6 @@ enum soc_au1200_ints {
#define MAC_RX_BUFF3_STATUS 0x30
#define MAC_RX_BUFF3_ADDR 0x34
/* UARTS 0-3 */
#define UART_BASE UART0_ADDR
#ifdef CONFIG_SOC_AU1200
#define UART_DEBUG_BASE UART1_ADDR
#else
#define UART_DEBUG_BASE UART3_ADDR
#endif
#define UART_RX 0 /* Receive buffer */
#define UART_TX 4 /* Transmit buffer */
#define UART_IER 8 /* Interrupt Enable Register */
......@@ -1282,84 +1268,6 @@ enum soc_au1200_ints {
#define UART_CLK 0x28 /* Baud Rate Clock Divider */
#define UART_MOD_CNTRL 0x100 /* Module Control */
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK 0xF0 /* Mask for the FIFO trigger range */
#define UART_FCR_R_TRIGGER_1 0x00 /* Mask for receive trigger set at 1 */
#define UART_FCR_R_TRIGGER_4 0x40 /* Mask for receive trigger set at 4 */
#define UART_FCR_R_TRIGGER_8 0x80 /* Mask for receive trigger set at 8 */
#define UART_FCR_R_TRIGGER_14 0xA0 /* Mask for receive trigger set at 14 */
#define UART_FCR_T_TRIGGER_0 0x00 /* Mask for transmit trigger set at 0 */
#define UART_FCR_T_TRIGGER_4 0x10 /* Mask for transmit trigger set at 4 */
#define UART_FCR_T_TRIGGER_8 0x20 /* Mask for transmit trigger set at 8 */
#define UART_FCR_T_TRIGGER_12 0x30 /* Mask for transmit trigger set at 12 */
/*
* These are the definitions for the Line Control Register
*/
#define UART_LCR_SBC 0x40 /* Set break control */
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
#define UART_LCR_EPAR 0x10 /* Even parity select */
#define UART_LCR_PARITY 0x08 /* Parity Enable */
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
/*
* These are the definitions for the Line Status Register
*/
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
#define UART_LSR_FE 0x08 /* Frame error indicator */
#define UART_LSR_PE 0x04 /* Parity error indicator */
#define UART_LSR_OE 0x02 /* Overrun error indicator */
#define UART_LSR_DR 0x01 /* Receiver data ready */
/*
* These are the definitions for the Interrupt Identification Register
*/
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
/*
* These are the definitions for the Interrupt Enable Register
*/
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
/*
* These are the definitions for the Modem Control Register
*/
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_MCR_OUT2 0x08 /* Out2 complement */
#define UART_MCR_OUT1 0x04 /* Out1 complement */
#define UART_MCR_RTS 0x02 /* RTS complement */
#define UART_MCR_DTR 0x01 /* DTR complement */
/*
* These are the definitions for the Modem Status Register
*/
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_RI 0x40 /* Ring Indicator */
#define UART_MSR_DSR 0x20 /* Data Set Ready */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR 0x02 /* Delta DSR */
#define UART_MSR_DCTS 0x01 /* Delta CTS */
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
/* SSIO */
#define SSI0_STATUS 0xB1600000
# define SSI_STATUS_BF (1 << 4)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment