[PATCH] ide: fix the HPT366 driver layer

The highpoint driver is unreadable, buggy and crashes on some chipsets.  The
-ac one is more readable (but not ideal) and doesn't crash all over the place.
 Been in Fedora for some time.

Backported from the Fedora one to the old Bartlomiej IDE core.  No other
dependencies.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

drivers/ide/pci/hpt366.c

@@ -10,6 +10,11 @@
  * donation of an ABit BP6 mainboard, processor, and memory acellerated
  * development and support.
  *
+ *
+ * Highpoint have their own driver (source except for the raid part)
+ * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz
+ * This may be useful to anyone wanting to work on the mainstream hpt IDE.
+ *
  * Note that final HPT370 support was done by force extraction of GPL.
  *
  * - add function for getting/setting power status of drive
@@ -446,44 +451,29 @@ static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = {
 #define F_LOW_PCI_50	0x2d
 #define F_LOW_PCI_66	0x42
 
-/* FIXME: compare with driver's code before removing */
-#if 0
-		if (hpt_minimum_revision(dev, 3)) {
-			u8 cbl;
-			cbl = inb(iobase + 0x7b);
-			outb(cbl | 1, iobase + 0x7b);
-			outb(cbl & ~1, iobase + 0x7b);
-			cbl = inb(iobase + 0x7a);
-			p += sprintf(p, "Cable:          ATA-%d"
-					"                          ATA-%d\n",
-				(cbl & 0x02) ? 33 : 66,
-				(cbl & 0x01) ? 33 : 66);
-			p += sprintf(p, "\n");
-		}
-		{
-			u8 c2, c3;
-			/* older revs don't have these registers mapped 
-			 * into io space */
-			pci_read_config_byte(dev, 0x43, &c0);
-			pci_read_config_byte(dev, 0x47, &c1);
-			pci_read_config_byte(dev, 0x4b, &c2);
-			pci_read_config_byte(dev, 0x4f, &c3);
-
-			p += sprintf(p, "Mode:           %s             %s"
-					"           %s              %s\n",
-				(c0 & 0x10) ? "UDMA" : (c0 & 0x20) ? "DMA " : 
-					(c0 & 0x80) ? "PIO " : "off ",
-				(c1 & 0x10) ? "UDMA" : (c1 & 0x20) ? "DMA " :
-					(c1 & 0x80) ? "PIO " : "off ",
-				(c2 & 0x10) ? "UDMA" : (c2 & 0x20) ? "DMA " :
-					(c2 & 0x80) ? "PIO " : "off ",
-				(c3 & 0x10) ? "UDMA" : (c3 & 0x20) ? "DMA " :
-					(c3 & 0x80) ? "PIO " : "off ");
-		}
-	}
-#endif
+/*
+ *	Hold all the highpoint quirks and revision information in one
+ *	place.
+ */
 
-static u32 hpt_revision (struct pci_dev *dev)
+struct hpt_info
+{
+	u8 max_mode;		/* Speeds allowed */
+	int revision;		/* Chipset revision */
+	int flags;		/* Chipset properties */
+#define PLL_MODE	1
+#define IS_372N		2
+				/* Speed table */
+	struct chipset_bus_clock_list_entry *speed;
+};
+
+/*
+ *	This wants fixing so that we do everything not by classrev
+ *	(which breaks on the newest chips) but by creating an
+ *	enumeration of chip variants and using that
+ */
+
+static __devinit u32 hpt_revision (struct pci_dev *dev)
 {
 	u32 class_rev;
 	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
@@ -507,37 +497,33 @@ static u32 hpt_revision (struct pci_dev *dev)
 	return class_rev;
 }
 
-static u32 hpt_minimum_revision (struct pci_dev *dev, int revision)
-{
-	unsigned int class_rev = hpt_revision(dev);
-	revision--;
-	return ((int) (class_rev > revision) ? 1 : 0);
-}
-
 static int check_in_drive_lists(ide_drive_t *drive, const char **list);
 
 static u8 hpt3xx_ratemask (ide_drive_t *drive)
 {
-	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hpt_info *info	= ide_get_hwifdata(hwif);
 	u8 mode			= 0;
 
-	if (hpt_minimum_revision(dev, 8)) {		/* HPT374 */
+	/* FIXME: TODO - move this to set info->mode once at boot */
+
+	if (info->revision >= 8) {		/* HPT374 */
 		mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3;
-	} else if (hpt_minimum_revision(dev, 7)) {	/* HPT371 */
+	} else if (info->revision >= 7) {	/* HPT371 */
 		mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3;
-	} else if (hpt_minimum_revision(dev, 6)) {	/* HPT302 */
+	} else if (info->revision >= 6) {	/* HPT302 */
 		mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3;
-	} else if (hpt_minimum_revision(dev, 5)) {	/* HPT372 */
+	} else if (info->revision >= 5) {	/* HPT372 */
 		mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3;
-	} else if (hpt_minimum_revision(dev, 4)) {	/* HPT370A */
+	} else if (info->revision >= 4) {	/* HPT370A */
 		mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
-	} else if (hpt_minimum_revision(dev, 3)) {	/* HPT370 */
+	} else if (info->revision >= 3) {	/* HPT370 */
 		mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
 		mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode;
 	} else {				/* HPT366 and HPT368 */
 		mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2;
 	}
-	if (!eighty_ninty_three(drive) && (mode))
+	if (!eighty_ninty_three(drive) && mode)
 		mode = min(mode, (u8)1);
 	return mode;
 }
@@ -549,7 +535,8 @@ static u8 hpt3xx_ratemask (ide_drive_t *drive)
  
 static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
 {
-	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hpt_info *info	= ide_get_hwifdata(hwif);
 	u8 mode			= hpt3xx_ratemask(drive);
 
 	if (drive->media != ide_disk)
@@ -561,7 +548,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
 			break;
 		case 0x03:
 			speed = min(speed, (u8)XFER_UDMA_5);
-			if (hpt_minimum_revision(dev, 5))
+			if (info->revision >= 5)
 				break;
 			if (check_in_drive_lists(drive, bad_ata100_5))
 				speed = min(speed, (u8)XFER_UDMA_4);
@@ -571,7 +558,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
 	/*
 	 * CHECK ME, Does this need to be set to 5 ??
 	 */
-			if (hpt_minimum_revision(dev, 3))
+			if (info->revision >= 3)
 				break;
 			if ((check_in_drive_lists(drive, bad_ata66_4)) ||
 			    (!(HPT366_ALLOW_ATA66_4)))
@@ -585,7 +572,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
 	/*
 	 * CHECK ME, Does this need to be set to 5 ??
 	 */
-			if (hpt_minimum_revision(dev, 3))
+			if (info->revision >= 3)
 				break;
 			if (check_in_drive_lists(drive, bad_ata33))
 				speed = min(speed, (u8)XFER_MW_DMA_2);
@@ -624,11 +611,12 @@ static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_
 
 static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 {
-	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev	= hwif->pci_dev;
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 	u8 speed		= hpt3xx_ratefilter(drive, xferspeed);
-//	u8 speed		= ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
 	u8 regtime		= (drive->select.b.unit & 0x01) ? 0x44 : 0x40;
-	u8 regfast		= (HWIF(drive)->channel) ? 0x55 : 0x51;
+	u8 regfast		= (hwif->channel) ? 0x55 : 0x51;
 	u8 drive_fast		= 0;
 	u32 reg1 = 0, reg2	= 0;
 
@@ -636,16 +624,11 @@ static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 	 * Disable the "fast interrupt" prediction.
 	 */
 	pci_read_config_byte(dev, regfast, &drive_fast);
-#if 0
-	if (drive_fast & 0x02)
-		pci_write_config_byte(dev, regfast, drive_fast & ~0x20);
-#else
 	if (drive_fast & 0x80)
 		pci_write_config_byte(dev, regfast, drive_fast & ~0x80);
-#endif
 
-	reg2 = pci_bus_clock_list(speed,
-		(struct chipset_bus_clock_list_entry *) pci_get_drvdata(dev));
+	reg2 = pci_bus_clock_list(speed, info->speed);
+
 	/*
 	 * Disable on-chip PIO FIFO/buffer
 	 *  (to avoid problems handling I/O errors later)
@@ -665,10 +648,11 @@ static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 
 static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 {
-	struct pci_dev *dev = HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev = hwif->pci_dev;
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 	u8 speed	= hpt3xx_ratefilter(drive, xferspeed);
-//	u8 speed	= ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
-	u8 regfast	= (HWIF(drive)->channel) ? 0x55 : 0x51;
+	u8 regfast	= (drive->hwif->channel) ? 0x55 : 0x51;
 	u8 drive_pci	= 0x40 + (drive->dn * 4);
 	u8 new_fast	= 0, drive_fast = 0;
 	u32 list_conf	= 0, drive_conf = 0;
@@ -693,17 +677,13 @@ static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 	if (new_fast != drive_fast)
 		pci_write_config_byte(dev, regfast, new_fast);
 
-	list_conf = pci_bus_clock_list(speed, 
-				       (struct chipset_bus_clock_list_entry *)
-				       pci_get_drvdata(dev));
+	list_conf = pci_bus_clock_list(speed, info->speed);
 
 	pci_read_config_dword(dev, drive_pci, &drive_conf);
 	list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
 	
-	if (speed < XFER_MW_DMA_0) {
+	if (speed < XFER_MW_DMA_0)
 		list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
-	}
-
 	pci_write_config_dword(dev, drive_pci, list_conf);
 
 	return ide_config_drive_speed(drive, speed);
@@ -711,10 +691,11 @@ static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 
 static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 {
-	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev	= hwif->pci_dev;
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 	u8 speed	= hpt3xx_ratefilter(drive, xferspeed);
-//	u8 speed	= ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
-	u8 regfast	= (HWIF(drive)->channel) ? 0x55 : 0x51;
+	u8 regfast	= (drive->hwif->channel) ? 0x55 : 0x51;
 	u8 drive_fast	= 0, drive_pci = 0x40 + (drive->dn * 4);
 	u32 list_conf	= 0, drive_conf = 0;
 	u32 conf_mask	= (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
@@ -726,10 +707,8 @@ static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 	pci_read_config_byte(dev, regfast, &drive_fast);
 	drive_fast &= ~0x07;
 	pci_write_config_byte(dev, regfast, drive_fast);
-					
-	list_conf = pci_bus_clock_list(speed,
-			(struct chipset_bus_clock_list_entry *)
-					pci_get_drvdata(dev));
+
+	list_conf = pci_bus_clock_list(speed, info->speed);
 	pci_read_config_dword(dev, drive_pci, &drive_conf);
 	list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
 	if (speed < XFER_MW_DMA_0)
@@ -741,19 +720,14 @@ static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 
 static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed)
 {
-	struct pci_dev *dev	= HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 
-	if (hpt_minimum_revision(dev, 8))
+	if (info->revision >= 8)
 		return hpt372_tune_chipset(drive, speed); /* not a typo */
-#if 0
-	else if (hpt_minimum_revision(dev, 7))
-		hpt371_tune_chipset(drive, speed);
-	else if (hpt_minimum_revision(dev, 6))
-		hpt302_tune_chipset(drive, speed);
-#endif
-	else if (hpt_minimum_revision(dev, 5))
+	else if (info->revision >= 5)
 		return hpt372_tune_chipset(drive, speed);
-	else if (hpt_minimum_revision(dev, 3))
+	else if (info->revision >= 3)
 		return hpt370_tune_chipset(drive, speed);
 	else	/* hpt368: hpt_minimum_revision(dev, 2) */
 		return hpt36x_tune_chipset(drive, speed);
@@ -779,8 +753,14 @@ static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio)
 static int config_chipset_for_dma (ide_drive_t *drive)
 {
 	u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive));
+	ide_hwif_t *hwif = drive->hwif;
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 
-	if (!(speed))
+	if (!speed)
+		return 0;
+
+	/* If we don't have any timings we can't do a lot */
+	if (info->speed == NULL)
 		return 0;
 
 	(void) hpt3xx_tune_chipset(drive, speed);
@@ -794,7 +774,7 @@ static int hpt3xx_quirkproc (ide_drive_t *drive)
 
 static void hpt3xx_intrproc (ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = HWIF(drive);
+	ide_hwif_t *hwif = drive->hwif;
 
 	if (drive->quirk_list)
 		return;
@@ -804,24 +784,26 @@ static void hpt3xx_intrproc (ide_drive_t *drive)
 
 static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
 {
-	struct pci_dev *dev = HWIF(drive)->pci_dev;
+	ide_hwif_t *hwif = drive->hwif;
+	struct hpt_info *info = ide_get_hwifdata(hwif);
+	struct pci_dev *dev = hwif->pci_dev;
 
 	if (drive->quirk_list) {
-		if (hpt_minimum_revision(dev,3)) {
+		if (info->revision >= 3) {
 			u8 reg5a = 0;
 			pci_read_config_byte(dev, 0x5a, &reg5a);
 			if (((reg5a & 0x10) >> 4) != mask)
 				pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10));
 		} else {
 			if (mask) {
-				disable_irq(HWIF(drive)->irq);
+				disable_irq(hwif->irq);
 			} else {
-				enable_irq(HWIF(drive)->irq);
+				enable_irq(hwif->irq);
 			}
 		}
 	} else {
 		if (IDE_CONTROL_REG)
-			HWIF(drive)->OUTB(mask ? (drive->ctl | 2) :
+			hwif->OUTB(mask ? (drive->ctl | 2) :
 						 (drive->ctl & ~2),
 						 IDE_CONTROL_REG);
 	}
@@ -829,12 +811,12 @@ static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
 
 static int hpt366_config_drive_xfer_rate (ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= HWIF(drive);
+	ide_hwif_t *hwif	= drive->hwif;
 	struct hd_driveid *id	= drive->id;
 
 	drive->init_speed = 0;
 
-	if (id && (id->capability & 1) && drive->autodma) {
+	if ((id->capability & 1) && drive->autodma) {
 
 		if (ide_use_dma(drive)) {
 			if (config_chipset_for_dma(drive))
@@ -868,15 +850,6 @@ static int hpt366_ide_dma_lostirq (ide_drive_t *drive)
 		drive->name, __FUNCTION__, reg50h, reg52h, reg5ah);
 	if (reg5ah & 0x10)
 		pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
-#if 0
-	/* how about we flush and reset, mmmkay? */
-	pci_write_config_byte(dev, 0x51, 0x1F);
-	/* fall through to a reset */
-	case dma_start:
-	case ide_dma_end:
-	/* reset the chips state over and over.. */
-	pci_write_config_byte(dev, 0x51, 0x13);
-#endif
 	return __ide_dma_lostirq(drive);
 }
 
@@ -919,7 +892,7 @@ static void hpt370_lostirq_timeout (ide_drive_t *drive)
 	u8 dma_stat = 0, dma_cmd = 0;
 
 	pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo);
-	printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
+	printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo);
 	hpt370_clear_engine(drive);
 	/* get dma command mode */
 	dma_cmd = hwif->INB(hwif->dma_command);
@@ -1047,15 +1020,6 @@ static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq)
 
 static void hpt3xx_reset (ide_drive_t *drive)
 {
-#if 0
-	unsigned long high_16	= pci_resource_start(HWIF(drive)->pci_dev, 4);
-	u8 reset	= (HWIF(drive)->channel) ? 0x80 : 0x40;
-	u8 reg59h	= 0;
-
-	pci_read_config_byte(HWIF(drive)->pci_dev, 0x59, &reg59h);
-	pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h|reset);
-	pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h);
-#endif
 }
 
 static int hpt3xx_tristate (ide_drive_t * drive, int state)
@@ -1065,8 +1029,6 @@ static int hpt3xx_tristate (ide_drive_t * drive, int state)
 	u8 reg59h = 0, reset	= (hwif->channel) ? 0x80 : 0x40;
 	u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
 
-//	hwif->bus_state = state;
-
 	pci_read_config_byte(dev, 0x59, &reg59h);
 	pci_read_config_byte(dev, state_reg, &regXXh);
 
@@ -1093,7 +1055,7 @@ static int hpt3xx_tristate (ide_drive_t * drive, int state)
 #define TRISTATE_BIT  0x8000
 static int hpt370_busproc(ide_drive_t * drive, int state)
 {
-	ide_hwif_t *hwif	= HWIF(drive);
+	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= hwif->pci_dev;
 	u8 tristate = 0, resetmask = 0, bus_reg = 0;
 	u16 tri_reg;
@@ -1148,33 +1110,44 @@ static int hpt370_busproc(ide_drive_t * drive, int state)
 	return 0;
 }
 
-static int __devinit init_hpt37x(struct pci_dev *dev)
+static void __devinit hpt366_clocking(ide_hwif_t *hwif)
 {
+	u32 reg1	= 0;
+	struct hpt_info *info = ide_get_hwifdata(hwif);
+
+	pci_read_config_dword(hwif->pci_dev, 0x40, &reg1);
+
+	/* detect bus speed by looking at control reg timing: */
+	switch((reg1 >> 8) & 7) {
+		case 5:
+			info->speed = forty_base_hpt366;
+			break;
+		case 9:
+			info->speed = twenty_five_base_hpt366;
+			break;
+		case 7:
+		default:
+			info->speed = thirty_three_base_hpt366;
+			break;
+	}
+}
+
+static void __devinit hpt37x_clocking(ide_hwif_t *hwif)
+{
+	struct hpt_info *info = ide_get_hwifdata(hwif);
+	struct pci_dev *dev = hwif->pci_dev;
 	int adjust, i;
 	u16 freq;
 	u32 pll;
 	u8 reg5bh;
-	u8 reg5ah = 0;
-	unsigned long dmabase = pci_resource_start(dev, 4);
-	u8 did, rid;	
-	int is_372n = 0;
 	
-	pci_read_config_byte(dev, 0x5a, &reg5ah);
-	/* interrupt force enable */
-	pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
-
-	if(dmabase)
-	{
-		did = inb(dmabase + 0x22);
-		rid = inb(dmabase + 0x28);
-	
-		if((did == 4 && rid == 6) || (did == 5 && rid > 1))
-			is_372n = 1;
-	}
-
 	/*
 	 * default to pci clock. make sure MA15/16 are set to output
-	 * to prevent drives having problems with 40-pin cables.
+	 * to prevent drives having problems with 40-pin cables. Needed
+	 * for some drives such as IBM-DTLA which will not enter ready
+	 * state on reset when PDIAG is a input.
+	 *
+	 * ToDo: should we set 0x21 when using PLL mode ?
 	 */
 	pci_write_config_byte(dev, 0x5b, 0x23);
 
@@ -1197,9 +1170,7 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
 	 * Currently we always set up the PLL for the 372N
 	 */
 	 
-	pci_set_drvdata(dev, NULL);
-	
-	if(is_372n)
+	if(info->flags & IS_372N)
 	{
 		printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n");
 		if(freq < 0x55)
@@ -1227,39 +1198,38 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
 			pll = F_LOW_PCI_66;
 	
 		if (pll == F_LOW_PCI_33) {
-			if (hpt_minimum_revision(dev,8))
-				pci_set_drvdata(dev, (void *) thirty_three_base_hpt374);
-			else if (hpt_minimum_revision(dev,5))
-				pci_set_drvdata(dev, (void *) thirty_three_base_hpt372);
-			else if (hpt_minimum_revision(dev,4))
-				pci_set_drvdata(dev, (void *) thirty_three_base_hpt370a);
+			if (info->revision >= 8)
+				info->speed = thirty_three_base_hpt374;
+			else if (info->revision >= 5)
+				info->speed = thirty_three_base_hpt372;
+			else if (info->revision >= 4)
+				info->speed = thirty_three_base_hpt370a;
 			else
-				pci_set_drvdata(dev, (void *) thirty_three_base_hpt370);
-			printk("HPT37X: using 33MHz PCI clock\n");
+				info->speed = thirty_three_base_hpt370;
+			printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n");
 		} else if (pll == F_LOW_PCI_40) {
 			/* Unsupported */
 		} else if (pll == F_LOW_PCI_50) {
-			if (hpt_minimum_revision(dev,8))
-				pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
-			else if (hpt_minimum_revision(dev,5))
-				pci_set_drvdata(dev, (void *) fifty_base_hpt372);
-			else if (hpt_minimum_revision(dev,4))
-				pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+			if (info->revision >= 8)
+				info->speed = fifty_base_hpt370a;
+			else if (info->revision >= 5)
+				info->speed = fifty_base_hpt372;
+			else if (info->revision >= 4)
+				info->speed = fifty_base_hpt370a;
 			else
-				pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
-			printk("HPT37X: using 50MHz PCI clock\n");
+				info->speed = fifty_base_hpt370a;
+			printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n");
 		} else {
-			if (hpt_minimum_revision(dev,8))
-			{
+			if (info->revision >= 8) {
 				printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n");
 			}
-			else if (hpt_minimum_revision(dev,5))
-				pci_set_drvdata(dev, (void *) sixty_six_base_hpt372);
-			else if (hpt_minimum_revision(dev,4))
-				pci_set_drvdata(dev, (void *) sixty_six_base_hpt370a);
+			else if (info->revision >= 5)
+				info->speed = sixty_six_base_hpt372;
+			else if (info->revision >= 4)
+				info->speed = sixty_six_base_hpt370a;
 			else
-				pci_set_drvdata(dev, (void *) sixty_six_base_hpt370);
-			printk("HPT37X: using 66MHz PCI clock\n");
+				info->speed = sixty_six_base_hpt370;
+			printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n");
 		}
 	}
 	
@@ -1269,11 +1239,19 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
 	 * result in slow reads when using a 33MHz PCI clock. we also
 	 * don't like to use the PLL because it will cause glitches
 	 * on PRST/SRST when the HPT state engine gets reset.
+	 *
+	 * ToDo: Use 66MHz PLL when ATA133 devices are present on a
+	 * 372 device so we can get ATA133 support
 	 */
-	if (pci_get_drvdata(dev)) 
+	if (info->speed)
 		goto init_hpt37X_done;
+
+	info->flags |= PLL_MODE;
 	
 	/*
+	 * FIXME: make this work correctly, esp with 372N as per
+	 * reference driver code.
+	 *
 	 * adjust PLL based upon PCI clock, enable it, and wait for
 	 * stabilization.
 	 */
@@ -1298,14 +1276,14 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
 				pci_write_config_dword(dev, 0x5c, 
 						       pll & ~0x100);
 				pci_write_config_byte(dev, 0x5b, 0x21);
-				if (hpt_minimum_revision(dev,8))
-					pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
-				else if (hpt_minimum_revision(dev,5))
-					pci_set_drvdata(dev, (void *) fifty_base_hpt372);
-				else if (hpt_minimum_revision(dev,4))
-					pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+				if (info->revision >= 8)
+					info->speed = fifty_base_hpt370a;
+				else if (info->revision >= 5)
+					info->speed = fifty_base_hpt372;
+				else if (info->revision >= 4)
+					info->speed = fifty_base_hpt370a;
 				else
-					pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+					info->speed = fifty_base_hpt370a;
 				printk("HPT37X: using 50MHz internal PLL\n");
 				goto init_hpt37X_done;
 			}
@@ -1318,10 +1296,22 @@ pll_recal:
 	} 
 
 init_hpt37X_done:
+	if (!info->speed)
+		printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n",
+			(info->flags & IS_372N)?"N":"", pll, freq);
 	/* reset state engine */
 	pci_write_config_byte(dev, 0x50, 0x37); 
 	pci_write_config_byte(dev, 0x54, 0x37); 
 	udelay(100);
+}
+
+static int __devinit init_hpt37x(struct pci_dev *dev)
+{
+	u8 reg5ah;
+
+	pci_read_config_byte(dev, 0x5a, &reg5ah);
+	/* interrupt force enable */
+	pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
 	return 0;
 }
 
@@ -1338,59 +1328,27 @@ static int __devinit init_hpt366(struct pci_dev *dev)
 		pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
 	pci_read_config_dword(dev, 0x40, &reg1);
 									
-	/* detect bus speed by looking at control reg timing: */
-	switch((reg1 >> 8) & 7) {
-		case 5:
-			pci_set_drvdata(dev, (void *) forty_base_hpt366);
-			break;
-		case 9:
-			pci_set_drvdata(dev, (void *) twenty_five_base_hpt366);
-			break;
-		case 7:
-		default:
-			pci_set_drvdata(dev, (void *) thirty_three_base_hpt366);
-			break;
-	}
-
-	if (!pci_get_drvdata(dev))
-	{
-		printk(KERN_ERR "hpt366: unknown bus timing.\n");
-		pci_set_drvdata(dev, NULL);
-	}
 	return 0;
 }
 
 static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
 {
 	int ret = 0;
-	u8 test = 0;
-
+	/* FIXME: Not portable */
 	if (dev->resource[PCI_ROM_RESOURCE].start)
 		pci_write_config_byte(dev, PCI_ROM_ADDRESS,
 			dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
 
-	pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &test);
-	if (test != (L1_CACHE_BYTES / 4))
-		pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE,
-			(L1_CACHE_BYTES / 4));
-
-	pci_read_config_byte(dev, PCI_LATENCY_TIMER, &test);
-	if (test != 0x78)
-		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
 
-	pci_read_config_byte(dev, PCI_MIN_GNT, &test);
-	if (test != 0x08)
-		pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
-
-	pci_read_config_byte(dev, PCI_MAX_LAT, &test);
-	if (test != 0x08)
-		pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
-
-	if (hpt_minimum_revision(dev, 3)) {
+	if (hpt_revision(dev) >= 3)
 		ret = init_hpt37x(dev);
-	} else {
-		ret =init_hpt366(dev);
-	}
+	else
+		ret = init_hpt366(dev);
+
 	if (ret)
 		return ret;
 
@@ -1400,27 +1358,16 @@ static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const cha
 static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 {
 	struct pci_dev *dev		= hwif->pci_dev;
+	struct hpt_info *info		= ide_get_hwifdata(hwif);
 	u8 ata66 = 0, regmask		= (hwif->channel) ? 0x01 : 0x02;
-	u8 did, rid;
-	unsigned long dmabase		= hwif->dma_base;
-	int is_372n = 0;
 	
-	if(dmabase)
-	{
-		did = inb(dmabase + 0x22);
-		rid = inb(dmabase + 0x28);
-	
-		if((did == 4 && rid == 6) || (did == 5 && rid > 1))
-			is_372n = 1;
-	}
-		
 	hwif->tuneproc			= &hpt3xx_tune_drive;
 	hwif->speedproc			= &hpt3xx_tune_chipset;
 	hwif->quirkproc			= &hpt3xx_quirkproc;
 	hwif->intrproc			= &hpt3xx_intrproc;
 	hwif->maskproc			= &hpt3xx_maskproc;
 	
-	if(is_372n)
+	if(info->flags & IS_372N)
 		hwif->rw_disk = &hpt372n_rw_disk;
 
 	/*
@@ -1428,7 +1375,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 	 * address lines to access an external eeprom.  To read valid
 	 * cable detect state the pins must be enabled as inputs.
 	 */
-	if (hpt_minimum_revision(dev, 8) && PCI_FUNC(dev->devfn) & 1) {
+	if (info->revision >= 8 && (PCI_FUNC(dev->devfn) & 1)) {
 		/*
 		 * HPT374 PCI function 1
 		 * - set bit 15 of reg 0x52 to enable TCBLID as input
@@ -1443,7 +1390,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 		pci_read_config_byte(dev, 0x5a, &ata66);
 		pci_write_config_word(dev, 0x52, mcr3);
 		pci_write_config_word(dev, 0x56, mcr6);
-	} else if (hpt_minimum_revision(dev, 3)) {
+	} else if (info->revision >= 3) {
 		/*
 		 * HPT370/372 and 374 pcifn 0
 		 * - clear bit 0 of 0x5b to enable P/SCBLID as inputs
@@ -1470,7 +1417,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 		hwif->serialized = hwif->mate->serialized = 1;
 #endif
 
-	if (hpt_minimum_revision(dev,3)) {
+	if (info->revision >= 3) {
 		u8 reg5ah = 0;
 			pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
 		/*
@@ -1480,8 +1427,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 		 */
 		hwif->resetproc	= &hpt3xx_reset;
 		hwif->busproc	= &hpt370_busproc;
-//		hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
-	} else if (hpt_minimum_revision(dev,2)) {
+	} else if (info->revision >= 2) {
 		hwif->resetproc	= &hpt3xx_reset;
 		hwif->busproc	= &hpt3xx_tristate;
 	} else {
@@ -1502,18 +1448,18 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 		hwif->udma_four = ((ata66 & regmask) ? 0 : 1);
 	hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
 
-	if (hpt_minimum_revision(dev,8)) {
+	if (info->revision >= 8) {
 		hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
 		hwif->ide_dma_end = &hpt374_ide_dma_end;
-	} else if (hpt_minimum_revision(dev,5)) {
+	} else if (info->revision >= 5) {
 		hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
 		hwif->ide_dma_end = &hpt374_ide_dma_end;
-	} else if (hpt_minimum_revision(dev,3)) {
+	} else if (info->revision >= 3) {
 		hwif->dma_start = &hpt370_ide_dma_start;
 		hwif->ide_dma_end = &hpt370_ide_dma_end;
 		hwif->ide_dma_timeout = &hpt370_ide_dma_timeout;
 		hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq;
-	} else if (hpt_minimum_revision(dev,2))
+	} else if (info->revision >= 2)
 		hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
 	else
 		hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
@@ -1526,6 +1472,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
 
 static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
 {
+	struct hpt_info	*info	= ide_get_hwifdata(hwif);
 	u8 masterdma	= 0, slavedma = 0;
 	u8 dma_new	= 0, dma_old = 0;
 	u8 primary	= hwif->channel ? 0x4b : 0x43;
@@ -1535,8 +1482,7 @@ static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
 	if (!dmabase)
 		return;
 		
-	if(pci_get_drvdata(hwif->pci_dev) == NULL)
-	{
+	if(info->speed == NULL) {
 		printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n");
 		return;
 	}
@@ -1559,6 +1505,40 @@ static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
 	ide_setup_dma(hwif, dmabase, 8);
 }
 
+/*
+ *	We "borrow" this hook in order to set the data structures
+ *	up early enough before dma or init_hwif calls are made.
+ */
+
+static void __devinit init_iops_hpt366(ide_hwif_t *hwif)
+{
+	struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
+	unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4);
+	u8 did, rid;
+
+	if(info == NULL) {
+		printk(KERN_WARNING "hpt366: out of memory.\n");
+		return;
+	}
+	memset(info, 0, sizeof(struct hpt_info));
+	ide_set_hwifdata(hwif, info);
+
+	if(dmabase) {
+		did = inb(dmabase + 0x22);
+		rid = inb(dmabase + 0x28);
+
+		if((did == 4 && rid == 6) || (did == 5 && rid > 1))
+			info->flags |= IS_372N;
+	}
+
+	info->revision = hpt_revision(hwif->pci_dev);
+
+	if (info->revision >= 3)
+		hpt37x_clocking(hwif);
+	else
+		hpt366_clocking(hwif);
+}
+
 static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
 {
 	struct pci_dev *findev = NULL;
@@ -1646,6 +1626,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT366",
 		.init_setup	= init_setup_hpt366,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,
@@ -1656,6 +1637,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT372A",
 		.init_setup	= init_setup_hpt37x,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,
@@ -1665,6 +1647,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT302",
 		.init_setup	= init_setup_hpt37x,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,
@@ -1674,6 +1657,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT371",
 		.init_setup	= init_setup_hpt37x,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,
@@ -1683,6 +1667,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT374",
 		.init_setup	= init_setup_hpt374,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,	/* 4 */
@@ -1692,6 +1677,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
 		.name		= "HPT372N",
 		.init_setup	= init_setup_hpt37x,
 		.init_chipset	= init_chipset_hpt366,
+		.init_iops	= init_iops_hpt366,
 		.init_hwif	= init_hwif_hpt366,
 		.init_dma	= init_dma_hpt366,
 		.channels	= 2,	/* 4 */