[PARISC] Move LBA and SBA register defines to the common ropes.h

header. This will allow the use of more constants in the
agpgart driver.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>

drivers/parisc/lba_pci.c

@@ -100,71 +100,6 @@
 
 #define MODULE_NAME "LBA"
 
-#define LBA_FUNC_ID	0x0000	/* function id */
-#define LBA_FCLASS	0x0008	/* function class, bist, header, rev... */
-#define LBA_CAPABLE	0x0030	/* capabilities register */
-
-#define LBA_PCI_CFG_ADDR	0x0040	/* poke CFG address here */
-#define LBA_PCI_CFG_DATA	0x0048	/* read or write data here */
-
-#define LBA_PMC_MTLT	0x0050	/* Firmware sets this - read only. */
-#define LBA_FW_SCRATCH	0x0058	/* Firmware writes the PCI bus number here. */
-#define LBA_ERROR_ADDR	0x0070	/* On error, address gets logged here */
-
-#define LBA_ARB_MASK	0x0080	/* bit 0 enable arbitration. PAT/PDC enables */
-#define LBA_ARB_PRI	0x0088	/* firmware sets this. */
-#define LBA_ARB_MODE	0x0090	/* firmware sets this. */
-#define LBA_ARB_MTLT	0x0098	/* firmware sets this. */
-
-#define LBA_MOD_ID	0x0100	/* Module ID. PDC_PAT_CELL reports 4 */
-
-#define LBA_STAT_CTL	0x0108	/* Status & Control */
-#define   LBA_BUS_RESET		0x01	/*  Deassert PCI Bus Reset Signal */
-#define   CLEAR_ERRLOG		0x10	/*  "Clear Error Log" cmd */
-#define   CLEAR_ERRLOG_ENABLE	0x20	/*  "Clear Error Log" Enable */
-#define   HF_ENABLE	0x40	/*    enable HF mode (default is -1 mode) */
-
-#define LBA_LMMIO_BASE	0x0200	/* < 4GB I/O address range */
-#define LBA_LMMIO_MASK	0x0208
-
-#define LBA_GMMIO_BASE	0x0210	/* > 4GB I/O address range */
-#define LBA_GMMIO_MASK	0x0218
-
-#define LBA_WLMMIO_BASE	0x0220	/* All < 4GB ranges under the same *SBA* */
-#define LBA_WLMMIO_MASK	0x0228
-
-#define LBA_WGMMIO_BASE	0x0230	/* All > 4GB ranges under the same *SBA* */
-#define LBA_WGMMIO_MASK	0x0238
-
-#define LBA_IOS_BASE	0x0240	/* I/O port space for this LBA */
-#define LBA_IOS_MASK	0x0248
-
-#define LBA_ELMMIO_BASE	0x0250	/* Extra LMMIO range */
-#define LBA_ELMMIO_MASK	0x0258
-
-#define LBA_EIOS_BASE	0x0260	/* Extra I/O port space */
-#define LBA_EIOS_MASK	0x0268
-
-#define LBA_GLOBAL_MASK	0x0270	/* Mercury only: Global Address Mask */
-#define LBA_DMA_CTL	0x0278	/* firmware sets this */
-
-#define LBA_IBASE	0x0300	/* SBA DMA support */
-#define LBA_IMASK	0x0308
-
-/* FIXME: ignore DMA Hint stuff until we can measure performance */
-#define LBA_HINT_CFG	0x0310
-#define LBA_HINT_BASE	0x0380	/* 14 registers at every 8 bytes. */
-
-#define LBA_BUS_MODE	0x0620
-
-/* ERROR regs are needed for config cycle kluges */
-#define LBA_ERROR_CONFIG 0x0680
-#define     LBA_SMART_MODE 0x20
-#define LBA_ERROR_STATUS 0x0688
-#define LBA_ROPE_CTL     0x06A0
-
-#define LBA_IOSAPIC_BASE	0x800 /* Offset of IRQ logic */
-
 /* non-postable I/O port space, densely packed */
 #define LBA_PORT_BASE	(PCI_F_EXTEND | 0xfee00000UL)
 static void __iomem *astro_iop_base __read_mostly;

drivers/parisc/sba_iommu.c

@@ -89,101 +89,6 @@
 
 #define DEFAULT_DMA_HINT_REG	0
 
-#define SBA_FUNC_ID	0x0000	/* function id */
-#define SBA_FCLASS	0x0008	/* function class, bist, header, rev... */
-
-#define SBA_FUNC_SIZE 4096   /* SBA configuration function reg set */
-
-#define ASTRO_IOC_OFFSET	(32 * SBA_FUNC_SIZE)
-#define PLUTO_IOC_OFFSET	(1 * SBA_FUNC_SIZE)
-/* Ike's IOC's occupy functions 2 and 3 */
-#define IKE_IOC_OFFSET(p)	((p+2) * SBA_FUNC_SIZE)
-
-#define IOC_CTRL          0x8	/* IOC_CTRL offset */
-#define IOC_CTRL_TC       (1 << 0) /* TOC Enable */
-#define IOC_CTRL_CE       (1 << 1) /* Coalesce Enable */
-#define IOC_CTRL_DE       (1 << 2) /* Dillon Enable */
-#define IOC_CTRL_RM       (1 << 8) /* Real Mode */
-#define IOC_CTRL_NC       (1 << 9) /* Non Coherent Mode */
-#define IOC_CTRL_D4       (1 << 11) /* Disable 4-byte coalescing */
-#define IOC_CTRL_DD       (1 << 13) /* Disable distr. LMMIO range coalescing */
-
-
-/*
-** Offsets into MBIB (Function 0 on Ike and hopefully Astro)
-** Firmware programs this stuff. Don't touch it.
-*/
-#define LMMIO_DIRECT0_BASE  0x300
-#define LMMIO_DIRECT0_MASK  0x308
-#define LMMIO_DIRECT0_ROUTE 0x310
-
-#define LMMIO_DIST_BASE  0x360
-#define LMMIO_DIST_MASK  0x368
-#define LMMIO_DIST_ROUTE 0x370
-
-#define IOS_DIST_BASE	0x390
-#define IOS_DIST_MASK	0x398
-#define IOS_DIST_ROUTE	0x3A0
-
-#define IOS_DIRECT_BASE	0x3C0
-#define IOS_DIRECT_MASK	0x3C8
-#define IOS_DIRECT_ROUTE 0x3D0
-
-/*
-** Offsets into I/O TLB (Function 2 and 3 on Ike)
-*/
-#define ROPE0_CTL	0x200  /* "regbus pci0" */
-#define ROPE1_CTL	0x208
-#define ROPE2_CTL	0x210
-#define ROPE3_CTL	0x218
-#define ROPE4_CTL	0x220
-#define ROPE5_CTL	0x228
-#define ROPE6_CTL	0x230
-#define ROPE7_CTL	0x238
-
-#define IOC_ROPE0_CFG	0x500	/* pluto only */
-#define   IOC_ROPE_AO	  0x10	/* Allow "Relaxed Ordering" */
-
-
-
-#define HF_ENABLE	0x40
-
-
-#define IOC_IBASE	0x300	/* IO TLB */
-#define IOC_IMASK	0x308
-#define IOC_PCOM	0x310
-#define IOC_TCNFG	0x318
-#define IOC_PDIR_BASE	0x320
-
-
-/*
-** IOC supports 4/8/16/64KB page sizes (see TCNFG register)
-** It's safer (avoid memory corruption) to keep DMA page mappings
-** equivalently sized to VM PAGE_SIZE.
-**
-** We really can't avoid generating a new mapping for each
-** page since the Virtual Coherence Index has to be generated
-** and updated for each page.
-**
-** PAGE_SIZE could be greater than IOVP_SIZE. But not the inverse.
-*/
-#define IOVP_SIZE	PAGE_SIZE
-#define IOVP_SHIFT	PAGE_SHIFT
-#define IOVP_MASK	PAGE_MASK
-
-#define SBA_PERF_CFG	0x708	/* Performance Counter stuff */
-#define SBA_PERF_MASK1	0x718
-#define SBA_PERF_MASK2	0x730
-
-
-/*
-** Offsets into PCI Performance Counters (functions 12 and 13)
-** Controlled by PERF registers in function 2 & 3 respectively.
-*/
-#define SBA_PERF_CNT1	0x200
-#define SBA_PERF_CNT2	0x208
-#define SBA_PERF_CNT3	0x210
-
 static struct sba_device *sba_list;
 
 static unsigned long ioc_needs_fdc = 0;
@@ -638,7 +543,7 @@ sba_io_pdir_entry(u64 *pdir_ptr, space_t sid, unsigned long vba,
 	asm("lci 0(%%sr1, %1), %0" : "=r" (ci) : "r" (vba));
 	pa |= (ci >> 12) & 0xff;  /* move CI (8 bits) into lowest byte */
 
-	pa |= 0x8000000000000000ULL;	/* set "valid" bit */
+	pa |= SBA_PDIR_VALID_BIT;	/* set "valid" bit */
 	*pdir_ptr = cpu_to_le64(pa);	/* swap and store into I/O Pdir */
 
 	/*

include/asm-parisc/ropes.h

@@ -101,7 +101,102 @@ static inline int IS_PLUTO(struct parisc_device *d) {
 	return d->id.hversion == PLUTO_MCKINLEY_PORT;
 }
 
-#define SBA_IOMMU_COOKIE	0x0000badbadc0ffeeUL
+#define PLUTO_IOVA_BASE	(1UL*1024*1024*1024)	/* 1GB */
+#define PLUTO_IOVA_SIZE	(1UL*1024*1024*1024)	/* 1GB */
+#define PLUTO_GART_SIZE	(PLUTO_IOVA_SIZE / 2)
+
+#define SBA_PDIR_VALID_BIT	0x8000000000000000ULL
+
+#define SBA_AGPGART_COOKIE	0x0000badbadc0ffeeULL
+
+#define SBA_FUNC_ID	0x0000	/* function id */
+#define SBA_FCLASS	0x0008	/* function class, bist, header, rev... */
+
+#define SBA_FUNC_SIZE 4096   /* SBA configuration function reg set */
+
+#define ASTRO_IOC_OFFSET	(32 * SBA_FUNC_SIZE)
+#define PLUTO_IOC_OFFSET	(1 * SBA_FUNC_SIZE)
+/* Ike's IOC's occupy functions 2 and 3 */
+#define IKE_IOC_OFFSET(p)	((p+2) * SBA_FUNC_SIZE)
+
+#define IOC_CTRL          0x8	/* IOC_CTRL offset */
+#define IOC_CTRL_TC       (1 << 0) /* TOC Enable */
+#define IOC_CTRL_CE       (1 << 1) /* Coalesce Enable */
+#define IOC_CTRL_DE       (1 << 2) /* Dillon Enable */
+#define IOC_CTRL_RM       (1 << 8) /* Real Mode */
+#define IOC_CTRL_NC       (1 << 9) /* Non Coherent Mode */
+#define IOC_CTRL_D4       (1 << 11) /* Disable 4-byte coalescing */
+#define IOC_CTRL_DD       (1 << 13) /* Disable distr. LMMIO range coalescing */
+
+/*
+** Offsets into MBIB (Function 0 on Ike and hopefully Astro)
+** Firmware programs this stuff. Don't touch it.
+*/
+#define LMMIO_DIRECT0_BASE  0x300
+#define LMMIO_DIRECT0_MASK  0x308
+#define LMMIO_DIRECT0_ROUTE 0x310
+
+#define LMMIO_DIST_BASE  0x360
+#define LMMIO_DIST_MASK  0x368
+#define LMMIO_DIST_ROUTE 0x370
+
+#define IOS_DIST_BASE	0x390
+#define IOS_DIST_MASK	0x398
+#define IOS_DIST_ROUTE	0x3A0
+
+#define IOS_DIRECT_BASE	0x3C0
+#define IOS_DIRECT_MASK	0x3C8
+#define IOS_DIRECT_ROUTE 0x3D0
+
+/*
+** Offsets into I/O TLB (Function 2 and 3 on Ike)
+*/
+#define ROPE0_CTL	0x200  /* "regbus pci0" */
+#define ROPE1_CTL	0x208
+#define ROPE2_CTL	0x210
+#define ROPE3_CTL	0x218
+#define ROPE4_CTL	0x220
+#define ROPE5_CTL	0x228
+#define ROPE6_CTL	0x230
+#define ROPE7_CTL	0x238
+
+#define IOC_ROPE0_CFG	0x500	/* pluto only */
+#define   IOC_ROPE_AO	  0x10	/* Allow "Relaxed Ordering" */
+
+#define HF_ENABLE	0x40
+
+#define IOC_IBASE	0x300	/* IO TLB */
+#define IOC_IMASK	0x308
+#define IOC_PCOM	0x310
+#define IOC_TCNFG	0x318
+#define IOC_PDIR_BASE	0x320
+
+/*
+** IOC supports 4/8/16/64KB page sizes (see TCNFG register)
+** It's safer (avoid memory corruption) to keep DMA page mappings
+** equivalently sized to VM PAGE_SIZE.
+**
+** We really can't avoid generating a new mapping for each
+** page since the Virtual Coherence Index has to be generated
+** and updated for each page.
+**
+** PAGE_SIZE could be greater than IOVP_SIZE. But not the inverse.
+*/
+#define IOVP_SIZE	PAGE_SIZE
+#define IOVP_SHIFT	PAGE_SHIFT
+#define IOVP_MASK	PAGE_MASK
+
+#define SBA_PERF_CFG	0x708	/* Performance Counter stuff */
+#define SBA_PERF_MASK1	0x718
+#define SBA_PERF_MASK2	0x730
+
+/*
+** Offsets into PCI Performance Counters (functions 12 and 13)
+** Controlled by PERF registers in function 2 & 3 respectively.
+*/
+#define SBA_PERF_CNT1	0x200
+#define SBA_PERF_CNT2	0x208
+#define SBA_PERF_CNT3	0x210
 
 /*
 ** lba_device: Per instance Elroy data structure
@@ -147,4 +242,69 @@ static inline int IS_QUICKSILVER(struct parisc_device *d) {
 extern void *iosapic_register(unsigned long hpa);
 extern int iosapic_fixup_irq(void *obj, struct pci_dev *pcidev);
 
+#define LBA_FUNC_ID	0x0000	/* function id */
+#define LBA_FCLASS	0x0008	/* function class, bist, header, rev... */
+#define LBA_CAPABLE	0x0030	/* capabilities register */
+
+#define LBA_PCI_CFG_ADDR	0x0040	/* poke CFG address here */
+#define LBA_PCI_CFG_DATA	0x0048	/* read or write data here */
+
+#define LBA_PMC_MTLT	0x0050	/* Firmware sets this - read only. */
+#define LBA_FW_SCRATCH	0x0058	/* Firmware writes the PCI bus number here. */
+#define LBA_ERROR_ADDR	0x0070	/* On error, address gets logged here */
+
+#define LBA_ARB_MASK	0x0080	/* bit 0 enable arbitration. PAT/PDC enables */
+#define LBA_ARB_PRI	0x0088	/* firmware sets this. */
+#define LBA_ARB_MODE	0x0090	/* firmware sets this. */
+#define LBA_ARB_MTLT	0x0098	/* firmware sets this. */
+
+#define LBA_MOD_ID	0x0100	/* Module ID. PDC_PAT_CELL reports 4 */
+
+#define LBA_STAT_CTL	0x0108	/* Status & Control */
+#define   LBA_BUS_RESET		0x01	/*  Deassert PCI Bus Reset Signal */
+#define   CLEAR_ERRLOG		0x10	/*  "Clear Error Log" cmd */
+#define   CLEAR_ERRLOG_ENABLE	0x20	/*  "Clear Error Log" Enable */
+#define   HF_ENABLE	0x40	/*    enable HF mode (default is -1 mode) */
+
+#define LBA_LMMIO_BASE	0x0200	/* < 4GB I/O address range */
+#define LBA_LMMIO_MASK	0x0208
+
+#define LBA_GMMIO_BASE	0x0210	/* > 4GB I/O address range */
+#define LBA_GMMIO_MASK	0x0218
+
+#define LBA_WLMMIO_BASE	0x0220	/* All < 4GB ranges under the same *SBA* */
+#define LBA_WLMMIO_MASK	0x0228
+
+#define LBA_WGMMIO_BASE	0x0230	/* All > 4GB ranges under the same *SBA* */
+#define LBA_WGMMIO_MASK	0x0238
+
+#define LBA_IOS_BASE	0x0240	/* I/O port space for this LBA */
+#define LBA_IOS_MASK	0x0248
+
+#define LBA_ELMMIO_BASE	0x0250	/* Extra LMMIO range */
+#define LBA_ELMMIO_MASK	0x0258
+
+#define LBA_EIOS_BASE	0x0260	/* Extra I/O port space */
+#define LBA_EIOS_MASK	0x0268
+
+#define LBA_GLOBAL_MASK	0x0270	/* Mercury only: Global Address Mask */
+#define LBA_DMA_CTL	0x0278	/* firmware sets this */
+
+#define LBA_IBASE	0x0300	/* SBA DMA support */
+#define LBA_IMASK	0x0308
+
+/* FIXME: ignore DMA Hint stuff until we can measure performance */
+#define LBA_HINT_CFG	0x0310
+#define LBA_HINT_BASE	0x0380	/* 14 registers at every 8 bytes. */
+
+#define LBA_BUS_MODE	0x0620
+
+/* ERROR regs are needed for config cycle kluges */
+#define LBA_ERROR_CONFIG 0x0680
+#define     LBA_SMART_MODE 0x20
+#define LBA_ERROR_STATUS 0x0688
+#define LBA_ROPE_CTL     0x06A0
+
+#define LBA_IOSAPIC_BASE	0x800 /* Offset of IRQ logic */
+
 #endif /*_ASM_PARISC_ROPES_H_*/