Commit 56b146d3 authored by Tobias Klauser's avatar Tobias Klauser Committed by Linus Torvalds

[PATCH] Last DMA_xBIT_MASK cleanups

These are the last conversions of pci_set_dma_mask(),
pci_set_consistent_dma_mask() and pci_dma_supported() to use DMA_xBIT_MASK
constants from linux/dma-mapping.h
Signed-off-by: default avatarTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent 31cc48bf
......@@ -194,7 +194,7 @@ document for how to handle this case.
Finally, if your device can only drive the low 24-bits of
address during PCI bus mastering you might do something like:
if (pci_set_dma_mask(pdev, 0x00ffffff)) {
if (pci_set_dma_mask(pdev, DMA_24BIT_MASK)) {
printk(KERN_WARNING
"mydev: 24-bit DMA addressing not available.\n");
goto ignore_this_device;
......
......@@ -1123,8 +1123,8 @@
if ((err = pci_enable_device(pci)) < 0)
return err;
/* check PCI availability (28bit DMA) */
if (pci_set_dma_mask(pci, 0x0fffffff) < 0 ||
pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) {
if (pci_set_dma_mask(pci, DMA_28BIT_MASK) < 0 ||
pci_set_consistent_dma_mask(pci, DMA_28BIT_MASK) < 0) {
printk(KERN_ERR "error to set 28bit mask DMA\n");
pci_disable_device(pci);
return -ENXIO;
......@@ -1236,8 +1236,8 @@
<![CDATA[
if ((err = pci_enable_device(pci)) < 0)
return err;
if (pci_set_dma_mask(pci, 0x0fffffff) < 0 ||
pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) {
if (pci_set_dma_mask(pci, DMA_28BIT_MASK) < 0 ||
pci_set_consistent_dma_mask(pci, DMA_28BIT_MASK) < 0) {
printk(KERN_ERR "error to set 28bit mask DMA\n");
pci_disable_device(pci);
return -ENXIO;
......
......@@ -32,6 +32,7 @@
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/dma-mapping.h>
#include "saa7134-reg.h"
#include "saa7134.h"
......@@ -870,7 +871,7 @@ static int __devinit saa7134_initdev(struct pci_dev *pci_dev,
pci_name(pci_dev), dev->pci_rev, pci_dev->irq,
dev->pci_lat,pci_resource_start(pci_dev,0));
pci_set_master(pci_dev);
if (!pci_dma_supported(pci_dev,0xffffffff)) {
if (!pci_dma_supported(pci_dev, DMA_32BIT_MASK)) {
printk("%s: Oops: no 32bit PCI DMA ???\n",dev->name);
err = -EIO;
goto fail1;
......
......@@ -11,6 +11,7 @@
#include <linux/errno.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
#include <linux/interrupt.h>
#include <linux/spinlock.h>
#include <linux/delay.h>
......@@ -619,9 +620,9 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id)
pci_set_master(pdev);
#ifdef USE_64BIT_DMA
ret = pci_set_dma_mask(pdev, 0xffffffffffffffffULL);
ret = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
if (!ret) {
ret = pci_set_consistent_dma_mask(pdev, 0xffffffffffffffffULL);
ret = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
if (ret < 0) {
printk(KERN_WARNING "%s: Unable to obtain 64 bit DMA "
"for consistent allocations\n",
......
......@@ -94,6 +94,7 @@
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/proc_fs.h>
#include <linux/dma-mapping.h>
#include "hwaccess.h"
#include "8010.h"
......@@ -119,7 +120,7 @@
/* the emu10k1 _seems_ to only supports 29 bit (512MiB) bit bus master */
#define EMU10K1_DMA_MASK 0x1fffffff /* DMA buffer mask for pci_alloc_consist */
#define EMU10K1_DMA_MASK DMA_29BIT_MASK /* DMA buffer mask for pci_alloc_consist */
#ifndef PCI_VENDOR_ID_CREATIVE
#define PCI_VENDOR_ID_CREATIVE 0x1102
......
......@@ -35,6 +35,7 @@
#include <linux/init.h>
#include <linux/moduleparam.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
......@@ -691,8 +692,8 @@ static int __devinit snd_als300_create(snd_card_t *card,
if ((err = pci_enable_device(pci)) < 0)
return err;
if (pci_set_dma_mask(pci, 0x0fffffff) < 0 ||
pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) {
if (pci_set_dma_mask(pci, DMA_28BIT_MASK) < 0 ||
pci_set_consistent_dma_mask(pci, DMA_28BIT_MASK) < 0) {
printk(KERN_ERR "error setting 28bit DMA mask\n");
pci_disable_device(pci);
return -ENXIO;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment