Merge commit 'hwlat/for-linus'

Documentation/hwlat_detector.txt

+Introduction:
+-------------
+
+The module hwlat_detector is a special purpose kernel module that is used to
+detect large system latencies induced by the behavior of certain underlying
+hardware or firmware, independent of Linux itself. The code was developed
+originally to detect SMIs (System Management Interrupts) on x86 systems,
+however there is nothing x86 specific about this patchset. It was
+originally written for use by the "RT" patch since the Real Time
+kernel is highly latency sensitive.
+
+SMIs are usually not serviced by the Linux kernel, which typically does not
+even know that they are occuring. SMIs are instead are set up by BIOS code
+and are serviced by BIOS code, usually for "critical" events such as
+management of thermal sensors and fans. Sometimes though, SMIs are used for
+other tasks and those tasks can spend an inordinate amount of time in the
+handler (sometimes measured in milliseconds). Obviously this is a problem if
+you are trying to keep event service latencies down in the microsecond range.
+
+The hardware latency detector works by hogging all of the cpus for configurable
+amounts of time (by calling stop_machine()), polling the CPU Time Stamp Counter
+for some period, then looking for gaps in the TSC data. Any gap indicates a
+time when the polling was interrupted and since the machine is stopped and
+interrupts turned off the only thing that could do that would be an SMI.
+
+Note that the SMI detector should *NEVER* be used in a production environment.
+It is intended to be run manually to determine if the hardware platform has a
+problem with long system firmware service routines.
+
+Usage:
+------
+
+Loading the module hwlat_detector passing the parameter "enabled=1" (or by
+setting the "enable" entry in "hwlat_detector" debugfs toggled on) is the only
+step required to start the hwlat_detector. It is possible to redefine the
+threshold in microseconds (us) above which latency spikes will be taken
+into account (parameter "threshold=").
+
+Example:
+
+	# modprobe hwlat_detector enabled=1 threshold=100
+
+After the module is loaded, it creates a directory named "hwlat_detector" under
+the debugfs mountpoint, "/debug/hwlat_detector" for this text. It is necessary
+to have debugfs mounted, which might be on /sys/debug on your system.
+
+The /debug/hwlat_detector interface contains the following files:
+
+count			- number of latency spikes observed since last reset
+enable			- a global enable/disable toggle (0/1), resets count
+max			- maximum hardware latency actually observed (usecs)
+sample			- a pipe from which to read current raw sample data
+			  in the format <timestamp> <latency observed usecs>
+			  (can be opened O_NONBLOCK for a single sample)
+threshold		- minimum latency value to be considered (usecs)
+width			- time period to sample with CPUs held (usecs)
+			  must be less than the total window size (enforced)
+window			- total period of sampling, width being inside (usecs)
+
+By default we will set width to 500,000 and window to 1,000,000, meaning that
+we will sample every 1,000,000 usecs (1s) for 500,000 usecs (0.5s). If we
+observe any latencies that exceed the threshold (initially 100 usecs),
+then we write to a global sample ring buffer of 8K samples, which is
+consumed by reading from the "sample" (pipe) debugfs file interface.

MAINTAINERS

@@ -2263,6 +2263,15 @@ W:	http://www.kernel.org/pub/linux/kernel/people/fseidel/hdaps/
 S:	Maintained
 F:	drivers/hwmon/hdaps.c
 
+HARDWARE LATENCY DETECTOR
+P:	Jon Masters
+M:	jcm@jonmasters.org
+W:	http://www.kernel.org/pub/linux/kernel/people/jcm/hwlat_detector/
+S:	Supported
+L:	linux-kernel@vger.kernel.org
+F:	Documentation/hwlat_detector.txt
+F:	drivers/misc/hwlat_detector.c
+
 HYPERVISOR VIRTUAL CONSOLE DRIVER
 L:	linuxppc-dev@ozlabs.org
 S:	Odd Fixes

drivers/misc/Kconfig

@@ -76,6 +76,35 @@ config IBM_ASM
 	  information on the specific driver level and support statement
 	  for your IBM server.
 
+config HWLAT_DETECTOR
+	tristate "Testing module to detect hardware-induced latencies"
+	depends on DEBUG_FS
+	depends on RING_BUFFER
+	default m
+	---help---
+	  A simple hardware latency detector. Use this module to detect
+	  large latencies introduced by the behavior of the underlying
+	  system firmware external to Linux. We do this using periodic
+	  use of stop_machine to grab all available CPUs and measure
+	  for unexplainable gaps in the CPU timestamp counter(s). By
+	  default, the module is not enabled until the "enable" file
+	  within the "hwlat_detector" debugfs directory is toggled.
+
+	  This module is often used to detect SMI (System Management
+	  Interrupts) on x86 systems, though is not x86 specific. To
+	  this end, we default to using a sample window of 1 second,
+	  during which we will sample for 0.5 seconds. If an SMI or
+	  similar event occurs during that time, it is recorded
+	  into an 8K samples global ring buffer until retreived.
+
+	  WARNING: This software should never be enabled (it can be built
+	  but should not be turned on after it is loaded) in a production
+	  environment where high latencies are a concern since the
+	  sampling mechanism actually introduces latencies for
+	  regular tasks while the CPU(s) are being held.
+
+	  If unsure, say N
+
 config PHANTOM
 	tristate "Sensable PHANToM (PCI)"
 	depends on PCI

drivers/misc/Makefile

@@ -21,5 +21,6 @@ obj-$(CONFIG_HP_ILO)		+= hpilo.o
 obj-$(CONFIG_ISL29003)		+= isl29003.o
 obj-$(CONFIG_EP93XX_PWM)	+= ep93xx_pwm.o
 obj-$(CONFIG_C2PORT)		+= c2port/
+obj-$(CONFIG_HWLAT_DETECTOR)	+= hwlat_detector.o
 obj-y				+= eeprom/
 obj-y				+= cb710/