avr32: Add support for Mediama RMTx add-on board for ATNGW100

Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

arch/avr32/boards/atngw100/Kconfig

@@ -21,6 +21,18 @@ config BOARD_ATNGW100_EVKLCD10X
 	  The MCI pins can be reenabled by editing the "add device function" but
 	  this may break the setup for other displays that use these pins.
 
+config BOARD_ATNGW100_MRMT
+	bool "Mediama RMT1/2 add-on board"
+	help
+	  This enables support for the Mediama RMT1 or RMT2 board.
+	  RMT provides LCD support, AC97 codec and other
+	  optional peripherals to the Atmel NGW100.
+
+	  This choice disables the detect pin and the write-protect pin for the
+	  MCI platform device, since it conflicts with the LCD platform device.
+	  The MCI pins can be reenabled by editing the "add device function" but
+	  this may break the setup for other displays that use these pins.
+
 endchoice
 
 choice
@@ -39,4 +51,8 @@ config BOARD_ATNGW100_EVKLCD10X_POW_QVGA
 
 endchoice
 
+if BOARD_ATNGW100_MRMT
+source	"arch/avr32/boards/atngw100/Kconfig_mrmt"
+endif
+
 endif	# BOARD_ATNGW100

arch/avr32/boards/atngw100/Kconfig_mrmt

+# RMT for NGW100 customization
+
+choice
+	prompt "RMT Version"
+	help
+	  Select the RMTx board version.
+
+config BOARD_MRMT_REV1
+	bool "RMT1"
+config BOARD_MRMT_REV2
+	bool "RMT2"
+
+endchoice
+
+config BOARD_MRMT_AC97
+	bool "Enable AC97 CODEC"
+	help
+	  Enable the UCB1400 AC97 CODEC driver.
+
+choice
+	prompt "Touchscreen Driver"
+	default BOARD_MRMT_ADS7846_TS
+
+config BOARD_MRMT_UCB1400_TS
+	bool "Use UCB1400 Touchscreen"
+
+config BOARD_MRMT_ADS7846_TS
+	bool "Use ADS7846 Touchscreen"
+
+endchoice
+
+choice
+	prompt "RMTx LCD Selection"
+	default BOARD_MRMT_LCD_DISABLE
+
+config BOARD_MRMT_LCD_DISABLE
+	bool "LCD Disabled"
+
+config BOARD_MRMT_LCD_LQ043T3DX0X
+	bool "Sharp LQ043T3DX0x or compatible"
+	help
+	  If using RMT2, be sure to load the resistor pack selectors accordingly
+
+if BOARD_MRMT_REV2
+config BOARD_MRMT_LCD_KWH043GM08
+	bool "Formike KWH043GM08 or compatible"
+	help
+	  Be sure to load the RMT2 resistor pack selectors accordingly
+endif
+
+endchoice
+
+if !BOARD_MRMT_LCD_DISABLE
+config BOARD_MRMT_BL_PWM
+	bool "Use PWM control for LCD Backlight"
+	help
+		Use PWM driver for controlling LCD Backlight.
+		Otherwise, LCD Backlight is always on.
+endif
+
+config BOARD_MRMT_RTC_I2C
+	bool "Use External RTC on I2C Bus"
+	help
+		RMT1 has an optional RTC device on the I2C bus.
+		It is a SII S35390A.  Be sure to select the
+		matching RTC driver.
+
+choice
+	prompt "Wireless Module on ttyS2"
+	default BOARD_MRMT_WIRELESS_ZB
+
+config BOARD_MRMT_WIRELESS_ZB
+	bool "Use ZigBee/802.15.4 Module"
+
+config BOARD_MRMT_WIRELESS_BT
+	bool "Use Bluetooth (HCI) Module"
+
+config BOARD_MRMT_WIRELESS_NONE
+	bool "Not Installed"
+endchoice

arch/avr32/boards/atngw100/Makefile

 obj-y					+= setup.o flash.o
 obj-$(CONFIG_BOARD_ATNGW100_EVKLCD10X)	+= evklcd10x.o
+obj-$(CONFIG_BOARD_ATNGW100_MRMT)	+= mrmt.o

arch/avr32/boards/atngw100/setup.c

@@ -56,8 +56,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
 static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+#if defined(CONFIG_BOARD_ATNGW100_EVKLCD10X) || defined(CONFIG_BOARD_ATNGW100_MRMT1)
+		.detect_pin     = GPIO_PIN_NONE,
+		.wp_pin         = GPIO_PIN_NONE,
+#else
 		.detect_pin	= GPIO_PIN_PC(25),
 		.wp_pin		= GPIO_PIN_PE(0),
+#endif
 	},
 };