Commit bdab4e87 authored by Darrick J. Wong's avatar Darrick J. Wong Committed by James Bottomley

[SCSI] libsas: support NCQ for SATA disks

This patch adds SATAII NCQ support to libsas.  Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller.  The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash.  Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc.  Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.

I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller.  The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously.  A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: default avatarDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
parent 797f49de
...@@ -828,8 +828,14 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc) ...@@ -828,8 +828,14 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
task->ata_task.retry_count = 1; task->ata_task.retry_count = 1;
task->task_state_flags = SAS_TASK_STATE_PENDING; task->task_state_flags = SAS_TASK_STATE_PENDING;
if (qc->tf.protocol == ATA_PROT_DMA) switch (qc->tf.protocol) {
case ATA_PROT_NCQ:
task->ata_task.use_ncq = 1;
/* fall through */
case ATA_PROT_DMA:
task->ata_task.dma_xfer = 1; task->ata_task.dma_xfer = 1;
break;
}
if (sas_ha->lldd_max_execute_num < 2) if (sas_ha->lldd_max_execute_num < 2)
res = i->dft->lldd_execute_task(task, 1, GFP_ATOMIC); res = i->dft->lldd_execute_task(task, 1, GFP_ATOMIC);
...@@ -962,7 +968,7 @@ static struct ata_port_operations sas_sata_ops = { ...@@ -962,7 +968,7 @@ static struct ata_port_operations sas_sata_ops = {
static struct ata_port_info sata_port_info = { static struct ata_port_info sata_port_info = {
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_SATA_RESET | .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_SATA_RESET |
ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA, ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | ATA_FLAG_NCQ,
.pio_mask = 0x1f, /* PIO0-4 */ .pio_mask = 0x1f, /* PIO0-4 */
.mwdma_mask = 0x07, /* MWDMA0-2 */ .mwdma_mask = 0x07, /* MWDMA0-2 */
.udma_mask = ATA_UDMA6, .udma_mask = ATA_UDMA6,
...@@ -1031,6 +1037,7 @@ int sas_target_alloc(struct scsi_target *starget) ...@@ -1031,6 +1037,7 @@ int sas_target_alloc(struct scsi_target *starget)
ap->private_data = found_dev; ap->private_data = found_dev;
ap->cbl = ATA_CBL_SATA; ap->cbl = ATA_CBL_SATA;
ap->scsi_host = shost;
found_dev->sata_dev.ap = ap; found_dev->sata_dev.ap = ap;
} }
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment